[RBASE-L] - RE: phantom field on a form

Patti Jakusz Fri, 27 Feb 2015 17:35:44 -0800

Yes, I will have to bite the bullet and start.  I have to select them 
individually, so I don't pick up the phantom field.  And then the field order 
gets screwed up when you copy them to a new form.  And all the radio buttons 
need fixing.  All the variables.  Just  a couple of hours I didn't need to 
waste.
Thank you for your suggestions though.

Patti
      From: Dan Goldberg <[email protected]>
 To: RBASE-L Mailing List <[email protected]> 
 Sent: Friday, February 27, 2015 6:22 PM
 Subject: [RBASE-L] - RE: phantom field on a form

Try to select them and copy them in a new 
form.    Dan Goldberg    From: [email protected] [mailto:[email protected]]On 
Behalf Of Patti Jakusz
Sent: Friday, February 27, 2015 2:50 PM
To: RBASE-L Mailing List
Subject: [RBASE-L] - RE: phantom field on a form    It took about 15 hours to 
create the report. I'm hoping there's another solution. Patti    From: jan 
johansen <[email protected]>
To: RBASE-L Mailing List <[email protected]>
Sent: Friday, February 27, 2015 5:13 PM
Subject: [RBASE-L] - RE: phantom field on a form    Patti,   Sometimes 
weirdness happens and the only way to fix is start over. Just re-create the 
form.   Jan       -----Original Message-----
From: Patti Jakusz <[email protected]>
To: [email protected] (RBASE-L Mailing List)
Date: Fri, 27 Feb 2015 22:06:45 +0000 (UTC)
Subject: [RBASE-L] - RE: phantom field on a form
   I could only find one of the fields that way.  The other one has coordinates 
that are nearby.  When I select it in object list, no field is highlighted by 
the dots on the form.  I'm looking right where the field should be.  When I 
click in object list and hit delete on the phantom field, nothing happens.   
Patti         From: "Richardson, Jeff" <[email protected]>
To: RBASE-L Mailing List <[email protected]>
Sent: Friday, February 27, 2015 4:57 PM
Subject: [RBASE-L] - RE: phantom field on a form   Regarding the removal of the 
unwanted field, I can select any form object from the object list with my mouse 
(blue dots appear around it when I do so, just like as if I clicked directly on 
the object) and then when I hit the delete key on the keyboard… poof, it’s 
gone.     From:[email protected] [mailto:[email protected]]On Behalf Of Patti 
Jakusz
Sent: Friday, February 27, 2015 4:41 PM
To: RBASE-L Mailing List
Subject: [RBASE-L] - phantom field on a form   Hello again,   I was tracing a 
form and noticed an eep was initiated 3 times on the same field.  I went into 
designer and only see one field  (a variable) that calls that eep.  I looked at 
Object List and it appears twice.  I can click on the Object List and find one 
of them, but not the other.  I looked in Tabbing order and it only appears 
once.    So I tried to use the left & top coordinates to find the phantom 
field.  The good variable is located Left: 159 and top: 292.  The bad one is 
Left: 161 and Top: 110.   I found a field that is near that location and moved 
it, but there's nothing underneath.  I tried to catch it by roping around that 
area and hitting delete, but it's still in my Object list.    I unloaded and 
loaded the form again, but it's still there.  Is there some other way I can 
delete that field?  I still don't know why the eep is executing 3 times either. 
  Thanks, Patti

[RBASE-L] - RE: phantom field on a form

Reply via email to