Chris Did you skip over and plug in to port 3 with the slave, swap the cord, Jerry
On Thu, Jun 25, 2020, 12:54 PM Chris Schaefer <[email protected]> wrote: > The system is critical to a farm watering operation so I wasn't able to > shut it down to try and swap the port 1 inverter with the port 2 inverter. > As for changing the power save settings, that is what alerted me to the > issue. Under no circumstance can you see a port 2 via the Mate. That's what > had me looking at the hub itself and that's when I noticed that the LED on > port 2 wasn't lighting up as the hub scrolled/polled by. > > Christopher > > On Thu, Jun 25, 2020 at 3:37 PM William Miller <[email protected]> > wrote: > >> Christopher; >> >> >> >> Just spit-balling here: is the secondary inverter asleep (hate the >> master/slave terminology…)? Try changing power save settings to make sure >> the secondary is awake and see if that changes the situation. Seems >> unlikely this will solve the problem, but it may provide some kind of clue. >> >> >> >> Also, did you try swapping primary and secondary? Run with secondary >> alone as primary? >> >> >> >> William Miller >> >> >> >> *From:* RE-wrenches [mailto:[email protected]] *On >> Behalf Of *Chris Schaefer >> *Sent:* Thursday, June 25, 2020 10:35 AM >> *To:* RE-wrenches >> *Subject:* [RE-wrenches] Slave Radian not showing up on Hub10 or @ Mate3s >> >> >> >> G'Day All, >> >> >> >> So I started up a system recently with two Radian 8048A's. The master is >> connected to port 1 and the slave connected to port 2 with the FlexNet at >> port 3. There are no OB charge controllers in the system. When the hub is >> polling (led's scrolling) nothing shows up for the slave at port 2. It's >> like the slave inverter doesn't exist. So I moved the slave and flexnet >> down to port 3 and 4. No change in the polling. I swapped out comm (factory >> green) cables. Again no change. Looking at the control board of the slave >> there is only one green led on which is located at the upper right-hand >> side. Otherwise no led's are on. I have 57v at the buss bar terminals of >> the inverter. Of course since there is no polling at the hub there is no >> way to view port 2 to view the slave at the Mate. >> >> >> >> Now the only thing that I didn't do was to try and use the manual on/off >> switch-jumper to start the slave. But in the past regardless of the >> inverter being on or off it would still show up on the hub. This is a new >> one and I'm looking for some direction here. >> >> >> >> Thanks, >> >> Christopher- >> >> Chris Schaefer’s >> <http://www.solarandwindfx.com> >> >> *Tel/Fax 585-229-2083 or Cell 585-748-1870 * >> *5115 South Hill Road ~ Canandaigua New York 14424www.solarandwindfx.com >> <http://www.solarandwindfx.com> ~ E-mail: **[email protected] >> <[email protected]>* >> >> Thomas Jefferson, the author of our great Constitution, once said, >> "democracy" will cease to exist when you take away from those who are >> willing to work and give to those who would not." >> _______________________________________________ >> List sponsored by Redwood Alliance >> >> List Address: [email protected] >> >> Change listserver email address & settings: >> http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org >> >> List-Archive: >> http://www.mail-archive.com/[email protected]/maillist.html >> >> List rules & etiquette: >> www.re-wrenches.org/etiquette.htm >> >> Check out or update participant bios: >> www.members.re-wrenches.org >> >> > > -- > > Chris Schaefer’s > <http:www.solarandwindfx.com> > > *Tel/Fax 585-229-2083 or Cell 585-748-1870 * > *5115 South Hill Road ~ Canandaigua New York 14424**www.solarandwindfx.com > <http://www.solarandwindfx.com> ~ E-mail: [email protected] > <[email protected]>* > > > Thomas Jefferson, the author of our great Constitution, once said, > "democracy" will cease to exist when you take away from those who are > willing to work and give to those who would not." > _______________________________________________ > List sponsored by Redwood Alliance > > List Address: [email protected] > > Change listserver email address & settings: > http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org > > List-Archive: > http://www.mail-archive.com/[email protected]/maillist.html > > List rules & etiquette: > www.re-wrenches.org/etiquette.htm > > Check out or update participant bios: > www.members.re-wrenches.org > >
_______________________________________________ List sponsored by Redwood Alliance List Address: [email protected] Change listserver email address & settings: http://lists.re-wrenches.org/options.cgi/re-wrenches-re-wrenches.org List-Archive: http://www.mail-archive.com/[email protected]/maillist.html List rules & etiquette: www.re-wrenches.org/etiquette.htm Check out or update participant bios: www.members.re-wrenches.org
