Rod,

This is always a fascinating topic!  Although there is a lot of information
on the Internet about solar power (sometimes called alternative power), you
must be careful to read between the lines to separate the facts from "urban
legends."

I am running two solar-powered systems right now, one of which is a Motorola
R1225 UHF repeater on a mountain ridge just a few miles from the Pacific
coast.  It has been operating continuously in commercial service for more
than three years.  I am soon going to emplace a prefabricated concrete
building which will house an MTR2000 repeater along with the existing
equipment.  Both repeaters will have separate power systems.

First and foremost, the batteries need to be intended for solar service.
Batteries designed for UPS duty are not necessarily the best choice for a
solar system.  I picked the SunWize Concorde model PVX-1040T batteries,
which are rated 12 volts and 100 AH.  I used two of these batteries in
parallel, because they would just fit inside the Hoffman enclosure when
lined up end to end, and the 205 AH battery is too wide.   My selection of a
200 AH (total) battery supply was based upon my desire to have at least a
three-day survival with limited or no sun, due to heavy overcast or fog.  I
had already used a kWH meter to record the average power consumption of the
repeater in normal day-to-day operation, and a 200 AH battery seemed okay.
The batteries have fuses in both positive and negative leads so that a fault
in one battery will not bring down the repeater.

Next, I selected two Siemens 75 watt solar panels, because I wanted to be
able to recharge the batteries during sunlit days while also running the
repeater.  The 150 watts of solar power will do this, even after the output
has degraded over time.  The panels are carefully oriented for optimum solar
insolation, which means they are aimed at True south (not magnetic or
compass south!) in azimuth, and are tilted for optimum daily energy recovery
during winter months when the days are short.  The angle is not changed for
summer months, because the energy recovery is much greater then, anyway.  A
Schottky diode bridge is used to parallel the two panels into the charge
controller, so that a fault in one panel will not bring down the repeater.
Note that the diodes that are integral to the solar panels do not have the
same function as the Schottky diode bridge.

Finally, I chose a SunWize "Steca" 20 ampere charge controller, with the LCD
readout.  This model uses a "smart" charging algorithm to maintain the
battery at peak charge while protecting both the battery and the load from
over- or under-voltage.  This charge controller has been around for a while,
and is pretty much the "gold standard."  You must be careful to set the
jumpers for the battery chemistry and the charging profile you need.  Also,
you *must* be careful to ground your system at only one point.  Since the
radio chassis is normally grounded by the antenna connection, you must be
careful to float the negative leads at the solar panels, the battery, and
the controller.

I visit the repeater site about once every six months to check out the
equipment, and the SOC (State of Charge) display has always shown 100%.  I
swap out the R1225 radio with the spare at that time, and take the old R1225
back to the shop for a complete FCC checkout.  As you might imagine, a cold
and windy mountaintop is not a good place to perform the required power,
sensitivity, and deviation checks!  I also have a spare charge controller
with me, but I have yet to need it.

The connection of a wind generator to a solar system should be done after
consulting with the maker of the charge controller.  It may be a good idea
to increase the capacity of the charge controller to handle the additional
source current.

73, Eric Lemmon WB6FLY


-----Original Message-----
From: [email protected]
[mailto:[EMAIL PROTECTED] On Behalf Of [EMAIL PROTECTED]
Sent: Sunday, February 19, 2006 12:22 PM
To: [email protected]
Subject: [Repeater-Builder] Solar-Wind Powered Repeaters

The topic of batteries has come up several times lately. I know that I 
have questions like a few others do. What I would like to ask is if 
you have a repeater on solar and or wind power, would you let the 
rest of us know what you are using to charge the batteries, what 
type of charge controller, what type of batteries and how the 
batteries are working for you.

I am using two 100aH UPS batteries (ordering two more), a single 
110 watt solar panel (will order one more this summer) and will be 
adding a homebrew wind generator. The one panel does not keep 
the batteries charged, so I have turned off the repeater for the 
winter. The solar controller that I am using now is the MorningStar 
SS-10L (will be using a homebrew when I add the other panel and 
wind generator). This is my first repeater off the power grid. Have 
had a lot of advise given, both good and conflicting.

My first question: are UPS batteries good to use for this application 
or should I be using some other type and why? As it is time to buy 
more batteries to get ready for this spring to finnish the project.

Be patient with us beginners, we are still learning and making 
mistakes. I for one do not have deep pockets; but I have two 
repeaters and I am not a club. A thank you goes to each one of you 
for your advise.

Rod




 
Yahoo! Groups Links



 








 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/Repeater-Builder/

<*> To unsubscribe from this group, send an email to:
    [EMAIL PROTECTED]

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/
 


Reply via email to