Hi Jeff right I will put an earpiece on the nhrc a/f to the tx. No I bought it off a chap in the usa who had changed his nhrc gear to another make, and it was factory made. I can now init the unit and change the password. I tried entering pppp0000 and it switched off as a repeater, entered pppp0001 and it was back on, so maybe I need to see if there is a setting that affects tx a/f. Iam in the UK by the way
73 Steve ----- Original Message ----- From: "Jeff Otterson" <[EMAIL PROTECTED]> To: <Repeater-Builder@yahoogroups.com> Sent: Sunday, February 19, 2006 7:18 PM Subject: Re: [Repeater-Builder] Re: NHRC-4 Controler > Yes. You should hear a courtesy beep at the least. > > Was your NHRC-4 a kit? > > Jeff > > At 01:04 PM 2/19/2006, you wrote: > >Thanks Jeff > > > >I did think this but as the CAS is required to key the TX > >thought I would connect it. Works fine I put a signal into the rx from my > >signal generator, green led and red led come on and the tx is keyed, after > >the timeout the tx unkeys. > >Am I correct in assuming that I should hear the cw OK and id tones on the > >A/F output to the tx, and that the tx should key > >I don't hear any tones > > > >73 > > > >Steve > >----- Original Message ----- > >From: "Jeff Otterson" <[EMAIL PROTECTED]> > >To: <Repeater-Builder@yahoogroups.com> > >Sent: Sunday, February 19, 2006 3:57 PM > >Subject: Re: [Repeater-Builder] Re: NHRC-4 Controler > > > > > > > Actually, the NHRC-4 will receive and process DTMF tones without any valid > > > CAS input transitions. It is designed that way, so it can be commanded > > > even if there is a stuck mike or the CAS won't transition for some other > > > reason. > > > > > > The CAS transition just makes the DTMF processing happen a bit faster. > > > > > > Jeff > > > > > > > > > > > > At 07:22 AM 2/19/2006, you wrote: > > > >Hi > > > > > > > >no, I have not connected the cas. The nhrc needs CAS high > > > >so I will try connecting the Rangr RX CAS line pin 12 on the > > > >control plug which goes to around 9v when squelch opens > > > > > > > >73 > > > > > > > >Steve` > > > >----- Original Message ----- > > > >From: "Coy Hilton" <[EMAIL PROTECTED]> > > > >To: <Repeater-Builder@yahoogroups.com> > > > >Sent: Sunday, February 19, 2006 3:17 AM > > > >Subject: [Repeater-Builder] Re: NHRC-4 Controler > > > > > > > > > > > > > Do you have the CAS hooked up from your receiver on the radio thay > > > > > you are using for the receiver? If not that would be my guess as to > > > > > why the controller doesn't know that you are talking to it. > > > > > > > > > > 73 and good luck > > > > > AC0Y > > > > > > > > > > > > > > > --- In Repeater-Builder@yahoogroups.com, "Steve Bainbridge" > > > > > <[EMAIL PROTECTED]> wrote: > > > > > > > > > > > > Hi > > > > > > need a bit of help please. > > > > > > I am trying to setup an NHRC-4 to work with > > > > > > 2 Ge Rangrs as a 6mtr rptr. > > > > > > I have connected the Rangr loudspeaker O/P > > > > > > to the nhrc primary a/f input, and the nhrc > > > > > > primary tx a/f to a small amp, so I can hear > > > > > > the tones, cw id etc. I made JP3 and applied 12v > > > > > > for a few seconds, then removed JP3 and from > > > > > > another radio tx,ed into the rptr rx. I the tx,ed > > > > > > again and sent dtmf 1234 to set the password, but I never > > > > > > got the CW OK signal. > > > > > > On the nhrc there are 5 led,s a yellow, green and red, then > > > > > > another green and red. I take it the yellow is dtmf received > > > > > > this is lit when I send dtmf tones. The green is CAS and red > > > > > > is TX primary channel. The 2nd green and red are CAS and TX > > > > > > secondary channel. > > > > > > I take it the CAS is only needed to make the nhrc key the rptr > > > > > > tx and is not needed to program the controller. So any ideas as > > > > > > to why I can't hear the tones, id,s etc > > > > > > > > > > > > 73 > > > > > > > > > > > > Steve M1SWB > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > > > No virus found in this incoming message. > > > > > Checked by AVG Free Edition. > > > > > Version: 7.1.375 / Virus Database: 267.15.11/264 - Release Date: > >17/02/06 > > > > > > > > > > > > > > > > > > > > > > > > > > > > >Yahoo! Groups Links > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > > > > > > > > > > > > > > > > > > > -- > > > No virus found in this incoming message. > > > Checked by AVG Free Edition. > > > Version: 7.1.375 / Virus Database: 267.15.11/264 - Release Date: 17/02/06 > > > > > > > > > > > > > > >Yahoo! Groups Links > > > > > > > > > > > > > > > Yahoo! Groups Links > > > > > > > > > -- > No virus found in this incoming message. > Checked by AVG Free Edition. > Version: 7.1.375 / Virus Database: 267.15.11/264 - Release Date: 17/02/06 > Yahoo! Groups Links <*> To visit your group on the web, go to: http://groups.yahoo.com/group/Repeater-Builder/ <*> To unsubscribe from this group, send an email to: [EMAIL PROTECTED] <*> Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/