Frank, jack is not that bad once you get to know him.
I suggest getting him working without rivendell in the mix and then either adding in rivendell or starting over once you have a working knowledge of jack. "Yes Jack is still my jack, but I still need a Jill" http://packet-in.org/repo/RPM09/_final_mixes/Jack_and_jill.ogg all the best, drew On Thu, Jul 13, 2017 at 10:44 PM, Frank White < [email protected]> wrote: > Adding the rate to the asound does not work. We have had to do that with > these sound adapters to make them work. With the new version of Rivendell > that does not work anymore. And to be honest it may be something else that > was updated. I think Jack is my solution. But I have tried to understand > Jack. But it seems pretty complicated. > > > On Thursday, July 13, 2017, Lorne Tyndale <[email protected]> wrote: > > You can always try running it through Jack. > > > > The other option is to add the rate line into your /etc/asound.conf file > > to try and force the card to 44100 > > > > I've had situations where either / both of the above have worked for me. > > > > Lorne Tyndale > > > > > > > >> > >> I would like to try but not sure I can identify what needs rolled back. > >> Sounds like I need to wipe the drive and start over. > >> > >> On Thursday, July 13, 2017, Steve Varholy <[email protected]> wrote: > >> > I had a similar issue with my appliance. The upgrade of the appliance > >> caused an update to the driver for the built-in soundcard. The updated > >> driver no longer supported 44.1. The only way to get it to work was run > 48k > >> sample rate and everything ran fast/not at all. > >> > > >> > Ended up getting another soundcard. > >> > > >> > Can you roll back just the driver? > >> > > >> > Steve Varholy > >> > President and General Manager > >> > > >> > </mail/u/2/s/?view=att&th=15d3c6d34539a56f&attid=0.3& > disp=emb&zw&atsh=1> > >> > > >> > The Historic Barringer Building > >> > > >> > 1338 Main Street - Suite 202 > >> > > >> > Columbia, South Carolina 29201 > >> > > >> > Office: (803) 753-7260 x 251 > >> > > >> > Direct: (803) 404-5535 > >> > > >> > Cell: (703) 585-2101 > >> > > >> > A Service of the Independent Media Foundation > >> > > >> > ________________________________ > >> > From: [email protected] < > >> [email protected]> on behalf of Frank > White < > >> [email protected]> > >> > Sent: Thursday, July 13, 2017 10:45:57 AM > >> > To: [email protected] > >> > Subject: [RDD] Audio Adapter Issue > >> > > >> > I am hoping someone on the list can point me in the right direction > with > >> an audio adapter issue. While trying to make the GPIO system work I > needed > >> to update to the latest version of Rivendell. I was on 2.5.5. Along > with > >> the Rivendell update I updated the other software. Now on version > 2.16.0. > >> Originally loaded the software using the Paravel Appliance Software. I > >> have always had to add "rate 44100" to the asound.conf file. But after > the > >> update the sound adapter would not be recognized by Rivendell. Changed > >> System Settings in RDADMIN to 44100 and the adapter shows up again. But > >> now the audio will play for about 2 seconds and then sound like white > >> noise. Anyone have any ideas? > >> > > >> > -- > >> > Frank White > >> > Frank White Technology > >> > > >> > >> -- > >> Frank White > >> Frank White Technology<hr>________________ > _______________________________ > >> Rivendell-dev mailing list > >> [email protected] > >> http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev > > > > -- > Frank White > Frank White Technology > > _______________________________________________ > Rivendell-dev mailing list > [email protected] > http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev > > -- Enjoy great *Bahamian Music* at: Bahamain Or Nuttin - http://www.bahamianornuttin.com <http://www.bahamianornuttin.com/>
_______________________________________________ Rivendell-dev mailing list [email protected] http://caspian.paravelsystems.com/mailman/listinfo/rivendell-dev
