I just did a fresh pull and compiled from source. There are no hm2_eth
drivers anywhere that I can find. The firmware for 7i80 is not under the
lib/firmware directory either.
How do I go about to get the complete source to build from?
-
Regards / Groete
Marius D. L
I am using the Hostmot 2 drivers but are not at the right computer now, I
could check within a few hurs.
> I just did a fresh pull and compiled from source. There are no hm2_eth
> drivers anywhere that I can find. The firmware for 7i80 is not under the
> lib/firmware directory either.
> How do I g
the 7i80 is similar to the 5i25 cards in that the firmware isn't loaded
each time - you have to load the using the mesa-flash utility.
(although it comes with a firmware installed - so you should be able to
test)
As far as the driver not being there - are you running rt-preemt
kernel? My gue
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
> Date: Thu, 26 Feb 2015 11:44:07 +
> From: Marius Liebenberg
> To: "Enhanced Machine Controller (EMC)"
> Subject: [Emc-users] hm2_eth driver missing
>
> I just did a fresh pull and compiled from source. There are no hm2_eth
> drivers anywhere t
Thanks Peter, the shebang does it nicely :)
I was not aware that I had to have a different flavour to run the
ethernet stuff. If I had done it right from the word go, where would I
have found the information? Or maybe I should ask where would one read
to find out about the different configurat
Having built multizone ovens and oven controls over the yearsYes, you can
control it with a general purpose machine control program, but the dedicated
temperature controllers you can buy on EBAY or occasionally from www.mpja.com
are very inexpensive and will give you much better control of t
You also want to read up on the configuration of the interface\
http://linuxcnc.org/docs/2.7/html/man/man9/hm2_eth.9.html
some more info..
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Uspace
sam
On 2/26/2015 8:26 AM, Marius Liebenberg wrote:
>Thanks Peter, the shebang does it nicely :)
> I wa
Am I right to say that I cannot run this implementation on Ubuntu 10.04?
I have to move to Debian?
-- Original Message --
From: "sam sokolik"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2015-02-26 16:36:34
Subject: Re: [Emc-users] hm2_eth driver missing
>You al
On Thu, Feb 26, 2015, at 09:30 AM, richsh...@comcast.net wrote:
> Also keep the safety stuff completely separate from the control stuff. By
> that I mean the overtemp limiter controls a mechanical contactor, not just
> turns the SSR signal off.
Yep. True story from work a few years ago: W
-- Original Message --
From: "Peter C. Wallace"
To: "Marius Liebenberg" ; "Enhanced Machine
Controller (EMC)"
Sent: 2015-02-26 17:13:54
Subject: Re: [Emc-users] hm2_eth driver missing
>On Thu, 26 Feb 2015, Marius Liebenberg wrote:
>
>>Date: Thu, 26 Feb 2015 15:04:32 +
>>From: Mari
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
> Date: Thu, 26 Feb 2015 15:04:32 +
> From: Marius Liebenberg
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] hm2_eth driver missing
>
> Am I right to say that I cannot run this implementation on Ubuntu 10.04?
> I have to mo
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
> Date: Thu, 26 Feb 2015 14:26:06 +
> From: Marius Liebenberg
> To: "Enhanced Machine Controller (EMC)"
> Subject: Re: [Emc-users] hm2_eth driver missing
>
> Thanks Peter, the shebang does it nicely :)
> I was not aware that I had to have a diff
Do anybody know where it might be possible to find the scaling constants for a
Agiecut AT 200 EDM machine?
I could count and measure myself but lack the correct intruments for accurate
measurements.
Nicklas Karlsson
-
On 02/26/2015 11:59 PM, Karlsson & Wang wrote:
> Do anybody know where it might be possible to find the scaling constants for
> a Agiecut AT 200 EDM machine?
>
> I could count and measure myself but lack the correct intruments for accurate
> measurements.
>
>
> Nicklas Karlsson
>
> --
14 matches
Mail list logo