Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Thank you Anthony very much. I really appreciated your guidance. I was able to 
make work with the sip setup and incoming calls are now working fine but it 
doesn't have caller ID. I have attached the logs.


below is the config.


control-plane
!
!
voice-port 0/2/0
 trunk-group FXO_EM
 no battery-reversal
 input gain 1
 echo-cancel mode 1
 no vad
 no comfort-noise
 connection plar 12089588038
 impedance 900r
 description 208-343-0207
 caller-id enable
!
voice-port 0/2/1
 trunk-group FXO_EM
 connection plar 12089588038
 description 208-343-3497
 caller-id enable


dial-peer voice 2 voip
 preference 1
 destination-pattern 1208958
 session protocol sipv2
 session target ipv4:10.170.99.12
 voice-class codec 1
 voice-class sip options-keepalive up-interval 12 down-interval 65 retry 2
 dtmf-relay rtp-nte
 no vad



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Friday, March 2, 2018 9:52 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Nope.  It's SIP or die dude.

You already have a SIP dial-peer pointing at CUCM:

dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
!

You still have an issue with the number you're dialing and what's in your 
destination pattern.  But if you use the above dial peer config on dial-peer 5, 
then maybe you'll actually send a SIP INVITE to CUCM.

I just want to say, there are bigger issues here than just your POTS call to 
CIPC.  I work for a Cisco Partner in your city, and if you want, we can talk 
about having me come help you in person on this project. Let me know.

On Fri, Mar 2, 2018 at 9:12 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Hi Anthony,


do you think I should change the setting between CUCM and Gateway to H.323 
instead of SIP? do you think that makes it easy?


Thanks

Hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 1:16 PM
To: Hamu Ebiso

Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
debug voip ccapi inout, and if you're using SIP, then debug ccsip messages as 
well.  the debug vpm signal is not very helpful, though it does show the port 
selected.

On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Thank you Anthony very much for your help.

The 19529473283<tel:(952)%20947-3283> for  connection plar 
19529473283<tel:(952)%20947-3283> I was testing with. After changing of few 
things on the gateway, I'm now seeing different messages when I run debug. The 
calls used to ring only one time and then fast busy, now it rings twice and 
then fax busy for incoming. for outgoing, it's says calls connot be completed 
as dialed.


Attached the new logs again. I really appreciate your help.


thanks again.

Hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 11:05 AM

To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
According to the debug, you're calling 19529473283<tel:(952)%20947-3283>.  Is 
that correct?


Called Number=19529473283<tel:(952)%20947-3283>(TON=Unknown, NPI=Unknown),

If so, then this debug is not for this gateway, because you're hitting Outgoing 
Dial-peer=5


Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
IS NON ISDN(3)

And dial-peer 5, while it exists in your config you pasted, it doesn't match 
the called number.

dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5
!

Even if it did match the destination pattern, you're missing some config on 
this dial-peer to make a SIP capable dial-peer, which means it's sending H323 
setup to CUCM.  If you built the gateway as H323, then I can see how it rang 
your CIPC, otherwise, if you built it as SIP, which you said you did, then it 
would never ring your CIPC.

So, something is not adding up here.

Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too 
terrible, but it's also not good practice to be using dial-peer 0.  It's really 
VoIP DP 0 that is messy though.


Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
Calli

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Nope.  It's SIP or die dude.

You already have a SIP dial-peer pointing at CUCM:

dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038 <(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
!

You still have an issue with the number you're dialing and what's in your
destination pattern.  But if you use the above dial peer config on
dial-peer 5, then maybe you'll actually send a SIP INVITE to CUCM.

I just want to say, there are bigger issues here than just your POTS call
to CIPC.  I work for a Cisco Partner in your city, and if you want, we can
talk about having me come help you in person on this project. Let me know.

On Fri, Mar 2, 2018 at 9:12 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> Hi Anthony,
>
>
> do you think I should change the setting between CUCM and Gateway to H.323
> instead of SIP? do you think that makes it easy?
>
>
> Thanks
>
> Hamu
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 1:16 PM
> *To:* Hamu Ebiso
>
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> debug voip ccapi inout, and if you're using SIP, then debug ccsip messages
> as well.  the debug vpm signal is not very helpful, though it does show the
> port selected.
>
> On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Thank you Anthony very much for your help.
>
> The 19529473283 <(952)%20947-3283> for  connection plar 19529473283
> <(952)%20947-3283> I was testing with. After changing of few things on
> the gateway, I'm now seeing different messages when I run debug. The calls
> used to ring only one time and then fast busy, now it rings twice and then
> fax busy for incoming. for outgoing, it's says calls connot be completed as
> dialed.
>
>
> Attached the new logs again. I really appreciate your help.
>
>
> thanks again.
>
> Hamu
>
>
> ----------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 11:05 AM
>
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> According to the debug, you're calling 19529473283 <(952)%20947-3283>.
> Is that correct?
>
> Called Number=19529473283 <(952)%20947-3283>(TON=Unknown, NPI=Unknown),
>
>
> If so, then this debug is not for this gateway, because you're hitting
> Outgoing Dial-peer=5
>
> Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
> IS NON ISDN(3)
>
>
> And dial-peer 5, while it exists in your config you pasted, it doesn't
> match the called number.
>
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
> !
>
> Even if it did match the destination pattern, you're missing some config
> on this dial-peer to make a SIP capable dial-peer, which means it's sending
> H323 setup to CUCM.  If you built the gateway as H323, then I can see how
> it rang your CIPC, otherwise, if you built it as SIP, which you said you
> did, then it would never ring your CIPC.
>
> So, something is not adding up here.
>
> Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
> terrible, but it's also not good practice to be using dial-peer 0.  It's
> really VoIP DP 0 that is messy though.
>
> Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
> Calling IE Present=FALSE,
>
>
>
> On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> --
> *From:* avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely di

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

let me change the config setting in CUCM to H.323 and let you know.


thank you for your help again.


thanks

Hamu



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Friday, March 2, 2018 9:07 AM
To: Hamu Ebiso; Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Unfortunately, again, the number you're calling 4131, is not matching the 
dial-peers you posted; however, the debugs are still saying you're hitting DP 
5, which is an H323 DP not SIP.

On Thu, Mar 1, 2018 at 1:44 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:


Here is the debug output for debug voip ccapi inout, and debug ccsip messages.


Thank you again for your help.




From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 1:16 PM
To: Hamu Ebiso

Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
debug voip ccapi inout, and if you're using SIP, then debug ccsip messages as 
well.  the debug vpm signal is not very helpful, though it does show the port 
selected.

On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Thank you Anthony very much for your help.

The 19529473283<tel:(952)%20947-3283> for  connection plar 
19529473283<tel:(952)%20947-3283> I was testing with. After changing of few 
things on the gateway, I'm now seeing different messages when I run debug. The 
calls used to ring only one time and then fast busy, now it rings twice and 
then fax busy for incoming. for outgoing, it's says calls connot be completed 
as dialed.


Attached the new logs again. I really appreciate your help.


thanks again.

Hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 11:05 AM

To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
According to the debug, you're calling 19529473283<tel:(952)%20947-3283>.  Is 
that correct?


Called Number=19529473283<tel:(952)%20947-3283>(TON=Unknown, NPI=Unknown),

If so, then this debug is not for this gateway, because you're hitting Outgoing 
Dial-peer=5


Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
IS NON ISDN(3)

And dial-peer 5, while it exists in your config you pasted, it doesn't match 
the called number.

dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5
!

Even if it did match the destination pattern, you're missing some config on 
this dial-peer to make a SIP capable dial-peer, which means it's sending H323 
setup to CUCM.  If you built the gateway as H323, then I can see how it rang 
your CIPC, otherwise, if you built it as SIP, which you said you did, then it 
would never ring your CIPC.

So, something is not adding up here.

Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too 
terrible, but it's also not good practice to be using dial-peer 0.  It's really 
VoIP DP 0 that is messy though.


Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
Calling IE Present=FALSE,


On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Hi Anthony,


yes the call was hitting the gateway because I was seeing FXO port going 
Off-Hook. The problem was that Logging was not setup in the gateway. After I 
setup the Logging, I'm now seeing logs.


I have attached the log.

thanks

Hamu


From: avhollo...@gmail.com<mailto:avhollo...@gmail.com> 
<avhollo...@gmail.com<mailto:avhollo...@gmail.com>> on behalf of Anthony 
Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 8:45 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group

Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
Since you didn't see the call in your debugs, your call likely didn't hit your 
gateway.

Can you confirm how you made your test call, when you had your debug running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 dir

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Hi Anthony,


do you think I should change the setting between CUCM and Gateway to H.323 
instead of SIP? do you think that makes it easy?


Thanks

Hamu



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Thursday, March 1, 2018 1:16 PM
To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

debug voip ccapi inout, and if you're using SIP, then debug ccsip messages as 
well.  the debug vpm signal is not very helpful, though it does show the port 
selected.

On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Thank you Anthony very much for your help.

The 19529473283<tel:(952)%20947-3283> for  connection plar 
19529473283<tel:(952)%20947-3283> I was testing with. After changing of few 
things on the gateway, I'm now seeing different messages when I run debug. The 
calls used to ring only one time and then fast busy, now it rings twice and 
then fax busy for incoming. for outgoing, it's says calls connot be completed 
as dialed.


Attached the new logs again. I really appreciate your help.


thanks again.

Hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 11:05 AM

To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
According to the debug, you're calling 19529473283<tel:(952)%20947-3283>.  Is 
that correct?


Called Number=19529473283<tel:(952)%20947-3283>(TON=Unknown, NPI=Unknown),

If so, then this debug is not for this gateway, because you're hitting Outgoing 
Dial-peer=5


Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
IS NON ISDN(3)

And dial-peer 5, while it exists in your config you pasted, it doesn't match 
the called number.

dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5
!

Even if it did match the destination pattern, you're missing some config on 
this dial-peer to make a SIP capable dial-peer, which means it's sending H323 
setup to CUCM.  If you built the gateway as H323, then I can see how it rang 
your CIPC, otherwise, if you built it as SIP, which you said you did, then it 
would never ring your CIPC.

So, something is not adding up here.

Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too 
terrible, but it's also not good practice to be using dial-peer 0.  It's really 
VoIP DP 0 that is messy though.


Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
Calling IE Present=FALSE,


On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Hi Anthony,


yes the call was hitting the gateway because I was seeing FXO port going 
Off-Hook. The problem was that Logging was not setup in the gateway. After I 
setup the Logging, I'm now seeing logs.


I have attached the log.

thanks

Hamu


From: avhollo...@gmail.com<mailto:avhollo...@gmail.com> 
<avhollo...@gmail.com<mailto:avhollo...@gmail.com>> on behalf of Anthony 
Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 8:45 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group

Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
Since you didn't see the call in your debugs, your call likely didn't hit your 
gateway.

Can you confirm how you made your test call, when you had your debug running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 direct-inward-dial
dial-peer voice 911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 911
dial-peer voice 9911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 9911
dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
dial-peer voice 3 voip
 preference 2
 destination-pattern 12086858038<tel:(208)%20685-8038>
 

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Unfortunately, again, the number you're calling 4131, is not matching the
dial-peers you posted; however, the debugs are still saying you're hitting
DP 5, which is an H323 DP not SIP.

On Thu, Mar 1, 2018 at 1:44 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

>
> Here is the debug output for debug voip ccapi inout, and debug ccsip
> messages.
>
>
> Thank you again for your help.
>
>
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 1:16 PM
> *To:* Hamu Ebiso
>
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> debug voip ccapi inout, and if you're using SIP, then debug ccsip messages
> as well.  the debug vpm signal is not very helpful, though it does show the
> port selected.
>
> On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Thank you Anthony very much for your help.
>
> The 19529473283 <(952)%20947-3283> for  connection plar 19529473283
> <(952)%20947-3283> I was testing with. After changing of few things on
> the gateway, I'm now seeing different messages when I run debug. The calls
> used to ring only one time and then fast busy, now it rings twice and then
> fax busy for incoming. for outgoing, it's says calls connot be completed as
> dialed.
>
>
> Attached the new logs again. I really appreciate your help.
>
>
> thanks again.
>
> Hamu
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 11:05 AM
>
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> According to the debug, you're calling 19529473283 <(952)%20947-3283>.
> Is that correct?
>
> Called Number=19529473283 <(952)%20947-3283>(TON=Unknown, NPI=Unknown),
>
>
> If so, then this debug is not for this gateway, because you're hitting
> Outgoing Dial-peer=5
>
> Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
> IS NON ISDN(3)
>
>
> And dial-peer 5, while it exists in your config you pasted, it doesn't
> match the called number.
>
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
> !
>
> Even if it did match the destination pattern, you're missing some config
> on this dial-peer to make a SIP capable dial-peer, which means it's sending
> H323 setup to CUCM.  If you built the gateway as H323, then I can see how
> it rang your CIPC, otherwise, if you built it as SIP, which you said you
> did, then it would never ring your CIPC.
>
> So, something is not adding up here.
>
> Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
> terrible, but it's also not good practice to be using dial-peer 0.  It's
> really VoIP DP 0 that is messy though.
>
> Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
> Calling IE Present=FALSE,
>
>
>
> On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> --
> *From:* avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely didn't hit
> your gateway.
>
> Can you confirm how you made your test call, when you had your debug
> running?
>
> On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote:
>
> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
>  trunkgroup FXO_EM
>  translation-profile incoming Inbound
>  call-block translation-profile incoming block_profile
>  call-block disconnect-cause incoming call-reject
>  incoming called-number .
>  direct-inward-dial
> dial-peer voice 911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 911

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

debug voip ccapi inout, and if you're using SIP, then debug ccsip messages
as well.  the debug vpm signal is not very helpful, though it does show the
port selected.

On Thu, Mar 1, 2018 at 1:05 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> Thank you Anthony very much for your help.
>
> The 19529473283 <(952)%20947-3283> for  connection plar 19529473283
> <(952)%20947-3283> I was testing with. After changing of few things on
> the gateway, I'm now seeing different messages when I run debug. The calls
> used to ring only one time and then fast busy, now it rings twice and then
> fax busy for incoming. for outgoing, it's says calls connot be completed as
> dialed.
>
>
> Attached the new logs again. I really appreciate your help.
>
>
> thanks again.
>
> Hamu
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 11:05 AM
>
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> According to the debug, you're calling 19529473283 <(952)%20947-3283>.
> Is that correct?
>
> Called Number=19529473283 <(952)%20947-3283>(TON=Unknown, NPI=Unknown),
>
>
> If so, then this debug is not for this gateway, because you're hitting
> Outgoing Dial-peer=5
>
> Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
> IS NON ISDN(3)
>
>
> And dial-peer 5, while it exists in your config you pasted, it doesn't
> match the called number.
>
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
> !
>
> Even if it did match the destination pattern, you're missing some config
> on this dial-peer to make a SIP capable dial-peer, which means it's sending
> H323 setup to CUCM.  If you built the gateway as H323, then I can see how
> it rang your CIPC, otherwise, if you built it as SIP, which you said you
> did, then it would never ring your CIPC.
>
> So, something is not adding up here.
>
> Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
> terrible, but it's also not good practice to be using dial-peer 0.  It's
> really VoIP DP 0 that is messy though.
>
> Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
> Calling IE Present=FALSE,
>
>
>
> On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:
>
> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> ----------
> *From:* avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely didn't hit
> your gateway.
>
> Can you confirm how you made your test call, when you had your debug
> running?
>
> On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote:
>
> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
>  trunkgroup FXO_EM
>  translation-profile incoming Inbound
>  call-block translation-profile incoming block_profile
>  call-block disconnect-cause incoming call-reject
>  incoming called-number .
>  direct-inward-dial
> dial-peer voice 911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 911
> dial-peer voice 9911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 9911
> dial-peer voice 2 voip
>  description CUCM Dial-Peer - Inbound
>  preference 1
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session protocol sipv2
>  session target ipv4:10.0.2.6
>  incoming uri via 10
>  voice-class codec 1
>  dtmf-relay rtp-nte sip-kpml
>  fax-relay ecm disable
>  fax nsf 00
>  ip qos dscp cs3 signaling
>  no vad
> dial-peer voice 3 voip
>  preference 2
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session target ipv4:10.0.2.3
> dial-peer voice 650 pots
>  trunkgroup Local
>  description Local outbound
>  

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Thank you Anthony very much for your help.

The 19529473283 for  connection plar 19529473283 I was testing with. After 
changing of few things on the gateway, I'm now seeing different messages when I 
run debug. The calls used to ring only one time and then fast busy, now it 
rings twice and then fax busy for incoming. for outgoing, it's says calls 
connot be completed as dialed.


Attached the new logs again. I really appreciate your help.


thanks again.

Hamu



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Thursday, March 1, 2018 11:05 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

According to the debug, you're calling 19529473283.  Is that correct?


Called Number=19529473283(TON=Unknown, NPI=Unknown),

If so, then this debug is not for this gateway, because you're hitting Outgoing 
Dial-peer=5


Outgoing Dial-peer=5, Params=0x688FF3FC, Progress Indication=ORIGINATING SIDE 
IS NON ISDN(3)

And dial-peer 5, while it exists in your config you pasted, it doesn't match 
the called number.

dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020
 session target ipv4:10.0.2.5
!

Even if it did match the destination pattern, you're missing some config on 
this dial-peer to make a SIP capable dial-peer, which means it's sending H323 
setup to CUCM.  If you built the gateway as H323, then I can see how it rang 
your CIPC, otherwise, if you built it as SIP, which you said you did, then it 
would never ring your CIPC.

So, something is not adding up here.

Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too 
terrible, but it's also not good practice to be using dial-peer 0.  It's really 
VoIP DP 0 that is messy though.


Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON ISDN(3), 
Calling IE Present=FALSE,


On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Hi Anthony,


yes the call was hitting the gateway because I was seeing FXO port going 
Off-Hook. The problem was that Logging was not setup in the gateway. After I 
setup the Logging, I'm now seeing logs.


I have attached the log.

thanks

Hamu


From: avhollo...@gmail.com<mailto:avhollo...@gmail.com> 
<avhollo...@gmail.com<mailto:avhollo...@gmail.com>> on behalf of Anthony 
Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Thursday, March 1, 2018 8:45 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group

Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
Since you didn't see the call in your debugs, your call likely didn't hit your 
gateway.

Can you confirm how you made your test call, when you had your debug running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 direct-inward-dial
dial-peer voice 911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 911
dial-peer voice 9911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 9911
dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
dial-peer voice 3 voip
 preference 2
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session target ipv4:10.0.2.3
dial-peer voice 650 pots
 trunkgroup Local
 description Local outbound
 translation-profile outgoing Strip9
 destination-pattern 9208...
dial-peer voice 4 pots
 trunkgroup FXO_EM
 description ** 10-digit Local Call **
 translation-profile outgoing Strip9
 destination-pattern ^9[2-9]..[2-9]..$
 forward-digits 10
dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5


thank you very much!!


From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 1:29 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Maybe you're actually using MGCP then?  You still haven't shown the di

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

According to the debug, you're calling 19529473283.  Is that correct?

Called Number=19529473283(TON=Unknown, NPI=Unknown),


If so, then this debug is not for this gateway, because you're hitting
Outgoing Dial-peer=5

Outgoing Dial-peer=5, Params=0x688FF3FC, Progress
Indication=ORIGINATING SIDE IS NON ISDN(3)


And dial-peer 5, while it exists in your config you pasted, it doesn't
match the called number.

dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020
 session target ipv4:10.0.2.5
!

Even if it did match the destination pattern, you're missing some config on
this dial-peer to make a SIP capable dial-peer, which means it's sending
H323 setup to CUCM.  If you built the gateway as H323, then I can see how
it rang your CIPC, otherwise, if you built it as SIP, which you said you
did, then it would never ring your CIPC.

So, something is not adding up here.

Also, you're hitting Incoming Dial-peer=0, which on a POTS leg is not too
terrible, but it's also not good practice to be using dial-peer 0.  It's
really VoIP DP 0 that is messy though.

Incoming Dial-peer=0, Progress Indication=ORIGINATING SIDE IS NON
ISDN(3), Calling IE Present=FALSE,



On Thu, Mar 1, 2018 at 10:06 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> Hi Anthony,
>
>
> yes the call was hitting the gateway because I was seeing FXO port going
> Off-Hook. The problem was that Logging was not setup in the gateway. After
> I setup the Logging, I'm now seeing logs.
>
>
> I have attached the log.
>
>
> thanks
>
> Hamu
> --
> *From:* avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony
> Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Thursday, March 1, 2018 8:45 AM
> *To:* Hamu Ebiso
> *Cc:* Cisco VoIP Group
>
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> Since you didn't see the call in your debugs, your call likely didn't hit
> your gateway.
>
> Can you confirm how you made your test call, when you had your debug
> running?
>
> On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote:
>
> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
>  trunkgroup FXO_EM
>  translation-profile incoming Inbound
>  call-block translation-profile incoming block_profile
>  call-block disconnect-cause incoming call-reject
>  incoming called-number .
>  direct-inward-dial
> dial-peer voice 911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 911
> dial-peer voice 9911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 9911
> dial-peer voice 2 voip
>  description CUCM Dial-Peer - Inbound
>  preference 1
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session protocol sipv2
>  session target ipv4:10.0.2.6
>  incoming uri via 10
>  voice-class codec 1
>  dtmf-relay rtp-nte sip-kpml
>  fax-relay ecm disable
>  fax nsf 00
>  ip qos dscp cs3 signaling
>  no vad
> dial-peer voice 3 voip
>  preference 2
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session target ipv4:10.0.2.3
> dial-peer voice 650 pots
>  trunkgroup Local
>  description Local outbound
>  translation-profile outgoing Strip9
>  destination-pattern 9208...
> dial-peer voice 4 pots
>  trunkgroup FXO_EM
>  description ** 10-digit Local Call **
>  translation-profile outgoing Strip9
>  destination-pattern ^9[2-9]..[2-9]..$
>  forward-digits 10
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
>
>
> thank you very much!!
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 1:29 PM
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
>
> Maybe you're actually using MGCP then?  You still haven't shown the
> dial-peers on the gateway.  Is that because you don't have any?
>
> show run | section dial-peer
>
> On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, f

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Hi Anthony,


yes the call was hitting the gateway because I was seeing FXO port going 
Off-Hook. The problem was that Logging was not setup in the gateway. After I 
setup the Logging, I'm now seeing logs.


I have attached the log.

thanks

Hamu


From: avhollo...@gmail.com <avhollo...@gmail.com> on behalf of Anthony Holloway 
<avholloway+cisco-v...@gmail.com>
Sent: Thursday, March 1, 2018 8:45 AM
To: Hamu Ebiso
Cc: Cisco VoIP Group
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Since you didn't see the call in your debugs, your call likely didn't hit your 
gateway.

Can you confirm how you made your test call, when you had your debug running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 direct-inward-dial
dial-peer voice 911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 911
dial-peer voice 9911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 9911
dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
dial-peer voice 3 voip
 preference 2
 destination-pattern 12086858038<tel:(208)%20685-8038>
 session target ipv4:10.0.2.3
dial-peer voice 650 pots
 trunkgroup Local
 description Local outbound
 translation-profile outgoing Strip9
 destination-pattern 9208...
dial-peer voice 4 pots
 trunkgroup FXO_EM
 description ** 10-digit Local Call **
 translation-profile outgoing Strip9
 destination-pattern ^9[2-9]..[2-9]..$
 forward-digits 10
dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020<tel:(208)%20343-7020>
 session target ipv4:10.0.2.5


thank you very much!!


From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 1:29 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Maybe you're actually using MGCP then?  You still haven't shown the dial-peers 
on the gateway.  Is that because you don't have any?

show run | section dial-peer

On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

debug was turned on as shown below.


1#debug voice ccapi inout
voip ccapi inout debugging is on

made test calls and then show log, I see below output.

1#show log
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 
flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.


No Inactive Message Discriminator.

Console logging: level debugging, 517 messages logged, xml disabled,
 filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
 filtering disabled
Buffer logging:  level debugging, 550 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled

No active filter modules.

Trap logging: level debugging, 620 message lines logged
Logging to 10.0.7.139  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging to 10.0.8.12  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging Source-Interface:   VRF Name:
Loopback0


I don't see any calls activity.


thanks



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
But you

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Since you didn't see the call in your debugs, your call likely didn't hit
your gateway.

Can you confirm how you made your test call, when you had your debug
running?

On Feb 28, 2018 2:46 PM, "Hamu Ebiso" <hebiso2...@hotmail.com> wrote:

> Here is the dial-peer output
>
> 1#show run | sec dial-peer
> dial-peer voice 1 pots
>  trunkgroup FXO_EM
>  translation-profile incoming Inbound
>  call-block translation-profile incoming block_profile
>  call-block disconnect-cause incoming call-reject
>  incoming called-number .
>  direct-inward-dial
> dial-peer voice 911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 911
> dial-peer voice 9911 pots
>  trunkgroup FXO_EM
>  description Services
>  translation-profile outgoing Strip9
>  destination-pattern 9911
> dial-peer voice 2 voip
>  description CUCM Dial-Peer - Inbound
>  preference 1
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session protocol sipv2
>  session target ipv4:10.0.2.6
>  incoming uri via 10
>  voice-class codec 1
>  dtmf-relay rtp-nte sip-kpml
>  fax-relay ecm disable
>  fax nsf 00
>  ip qos dscp cs3 signaling
>  no vad
> dial-peer voice 3 voip
>  preference 2
>  destination-pattern 12086858038 <(208)%20685-8038>
>  session target ipv4:10.0.2.3
> dial-peer voice 650 pots
>  trunkgroup Local
>  description Local outbound
>  translation-profile outgoing Strip9
>  destination-pattern 9208...
> dial-peer voice 4 pots
>  trunkgroup FXO_EM
>  description ** 10-digit Local Call **
>  translation-profile outgoing Strip9
>  destination-pattern ^9[2-9]..[2-9]..$
>  forward-digits 10
> dial-peer voice 5 voip
>  description FXO test
>  destination-pattern 12083437020 <(208)%20343-7020>
>  session target ipv4:10.0.2.5
>
>
> thank you very much!!
>
> ------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 1:29 PM
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
>
> Maybe you're actually using MGCP then?  You still haven't shown the
> dial-peers on the gateway.  Is that because you don't have any?
>
> show run | section dial-peer
>
> On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, filtering disabled)
>
> No Active Message Discriminator.
>
>
> No Inactive Message Discriminator.
>
>
> Console logging: level debugging, 517 messages logged, xml disabled,
>  filtering disabled
> Monitor logging: level debugging, 0 messages logged, xml disabled,
>  filtering disabled
> Buffer logging:  level debugging, 550 messages logged, xml disabled,
> filtering disabled
> Exception Logging: size (4096 bytes)
> Count and timestamp logging messages: disabled
> Persistent logging: disabled
>
> No active filter modules.
>
> Trap logging: level debugging, 620 message lines logged
> Logging to 10.0.7.139  (udp port 514, audit disabled,
>   link up),
>   435 message lines logged,
>   0 message lines rate-limited,
>   0 message lines dropped-by-MD,
>   xml disabled, sequence number disabled
>   filtering disabled
> Logging to 10.0.8.12  (udp port 514, audit disabled,
>   link up),
>   435 message lines logged,
>   0 message lines rate-limited,
>   0 message lines dropped-by-MD,
>   xml disabled, sequence number disabled
>       filtering disabled
> Logging Source-Interface:   VRF Name:
> Loopback0
>
>
> I don't see any calls activity.
>
>
> thanks
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to captur

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

thank you very much for that info!! I checked under Preferences and optimize is 
not checked.



From: bmead...@gmail.com <bmead...@gmail.com> on behalf of Brian Meade 
<bmead...@vt.edu>
Sent: Wednesday, February 28, 2018 2:55 PM
To: Hamu Ebiso
Cc: Anthony Holloway; cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Didn't read the whole thread but make sure CIPC doesn't have "Optimize for low 
bandwidth" checked in the preferences.  This tries to force G.729.

On Wed, Feb 28, 2018 at 3:52 PM, Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Here is the region information.


[cid:8f436bad-8c75-481a-999e-8abf58c113af]


thank you very much for your help.


From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 1:31 PM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Regions are important for a working call flow, yes.  However, regions only 
exist on CUCM, not on gateways.

The way in which regions/codec selection could produce the issue your seeing is 
as follows:

Dial Peer has g711ulaw on it
CUCM SIP Trunk has Gateway-Region on it
CIPC has Phone-Region on it
Gateway-Region to Phone-Region is using 8kbps

On Wed, Feb 28, 2018 at 12:30 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Region is not define in the config but CUCM. Is that what you need? That is the 
only config I have. and don't see any region defined in the gateway.


thanks

hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
But you didn't send all the information, because your output doesn't show the 
dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for 
the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Brian Meade]

Didn't read the whole thread but make sure CIPC doesn't have "Optimize for
low bandwidth" checked in the preferences.  This tries to force G.729.

On Wed, Feb 28, 2018 at 3:52 PM, Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> Here is the region information.
>
>
>
> thank you very much for your help.
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 1:31 PM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
>
> Regions are important for a working call flow, yes.  However, regions only
> exist on CUCM, not on gateways.
>
> The way in which regions/codec selection could produce the issue your
> seeing is as follows:
>
> Dial Peer has g711ulaw on it
> CUCM SIP Trunk has Gateway-Region on it
> CIPC has Phone-Region on it
> Gateway-Region to Phone-Region is using 8kbps
>
> On Wed, Feb 28, 2018 at 12:30 PM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Region is not define in the config but CUCM. Is that what you need? That
> is the only config I have. and don't see any region defined in the gateway.
>
>
> thanks
>
> hamu
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either.  Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> ------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /9

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Here is the region information.


[cid:8f436bad-8c75-481a-999e-8abf58c113af]


thank you very much for your help.


From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Wednesday, February 28, 2018 1:31 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Regions are important for a working call flow, yes.  However, regions only 
exist on CUCM, not on gateways.

The way in which regions/codec selection could produce the issue your seeing is 
as follows:

Dial Peer has g711ulaw on it
CUCM SIP Trunk has Gateway-Region on it
CIPC has Phone-Region on it
Gateway-Region to Phone-Region is using 8kbps

On Wed, Feb 28, 2018 at 12:30 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Region is not define in the config but CUCM. Is that what you need? That is the 
only config I have. and don't see any region defined in the gateway.


thanks

hamu



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
But you didn't send all the information, because your output doesn't show the 
dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for 
the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice translation-profile Inbound
 translate called 1
!
voice translation-profile Strip9
 translate called 10
!
voice translation-profile block_profile
 translate calling 15
!
voice translation-profile outbound
 translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
 log config
  hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Here is the dial-peer output

1#show run | sec dial-peer
dial-peer voice 1 pots
 trunkgroup FXO_EM
 translation-profile incoming Inbound
 call-block translation-profile incoming block_profile
 call-block disconnect-cause incoming call-reject
 incoming called-number .
 direct-inward-dial
dial-peer voice 911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 911
dial-peer voice 9911 pots
 trunkgroup FXO_EM
 description Services
 translation-profile outgoing Strip9
 destination-pattern 9911
dial-peer voice 2 voip
 description CUCM Dial-Peer - Inbound
 preference 1
 destination-pattern 12086858038
 session protocol sipv2
 session target ipv4:10.0.2.6
 incoming uri via 10
 voice-class codec 1
 dtmf-relay rtp-nte sip-kpml
 fax-relay ecm disable
 fax nsf 00
 ip qos dscp cs3 signaling
 no vad
dial-peer voice 3 voip
 preference 2
 destination-pattern 12086858038
 session target ipv4:10.0.2.3
dial-peer voice 650 pots
 trunkgroup Local
 description Local outbound
 translation-profile outgoing Strip9
 destination-pattern 9208...
dial-peer voice 4 pots
 trunkgroup FXO_EM
 description ** 10-digit Local Call **
 translation-profile outgoing Strip9
 destination-pattern ^9[2-9]..[2-9]..$
 forward-digits 10
dial-peer voice 5 voip
 description FXO test
 destination-pattern 12083437020
 session target ipv4:10.0.2.5


thank you very much!!


From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Wednesday, February 28, 2018 1:29 PM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

Maybe you're actually using MGCP then?  You still haven't shown the dial-peers 
on the gateway.  Is that because you don't have any?

show run | section dial-peer

On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

debug was turned on as shown below.


1#debug voice ccapi inout
voip ccapi inout debugging is on

made test calls and then show log, I see below output.

1#show log
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 
flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.


No Inactive Message Discriminator.

Console logging: level debugging, 517 messages logged, xml disabled,
 filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
 filtering disabled
Buffer logging:  level debugging, 550 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled

No active filter modules.

Trap logging: level debugging, 620 message lines logged
Logging to 10.0.7.139  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging to 10.0.8.12  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging Source-Interface:   VRF Name:
Loopback0


I don't see any calls activity.


thanks



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 11:19 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
But you didn't send all the information, because your output doesn't show the 
dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for 
the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know 

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Regions are important for a working call flow, yes.  However, regions only
exist on CUCM, not on gateways.

The way in which regions/codec selection could produce the issue your
seeing is as follows:

Dial Peer has g711ulaw on it
CUCM SIP Trunk has Gateway-Region on it
CIPC has Phone-Region on it
Gateway-Region to Phone-Region is using 8kbps

On Wed, Feb 28, 2018 at 12:30 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> Region is not define in the config but CUCM. Is that what you need? That
> is the only config I have. and don't see any region defined in the gateway.
>
>
> thanks
>
> hamu
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either.  Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
>  rule 4 /^9\(011.*\)/ /\1/
>  rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
>  translate calling 91
>  translate called 1
> !
> voice translation-profile Inbound
>  translate called 1
> !
> voice translation-profile Strip9
>  translate called 10
> !
> voice translation-profile block_profile
>  translate calling 15
> !
> voice translation-profile outbound
>  translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> lic

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

Maybe you're actually using MGCP then?  You still haven't shown the
dial-peers on the gateway.  Is that because you don't have any?

show run | section dial-peer

On Wed, Feb 28, 2018 at 12:19 PM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> debug was turned on as shown below.
>
>
> 1#debug voice ccapi inout
> voip ccapi inout debugging is on
>
> made test calls and then show log, I see below output.
>
> 1#show log
> Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0
> flushes, 0 overruns, xml disabled, filtering disabled)
>
> No Active Message Discriminator.
>
>
> No Inactive Message Discriminator.
>
>
> Console logging: level debugging, 517 messages logged, xml disabled,
>  filtering disabled
> Monitor logging: level debugging, 0 messages logged, xml disabled,
>  filtering disabled
> Buffer logging:  level debugging, 550 messages logged, xml disabled,
> filtering disabled
> Exception Logging: size (4096 bytes)
> Count and timestamp logging messages: disabled
> Persistent logging: disabled
>
> No active filter modules.
>
> Trap logging: level debugging, 620 message lines logged
> Logging to 10.0.7.139  (udp port 514, audit disabled,
>   link up),
>   435 message lines logged,
>   0 message lines rate-limited,
>   0 message lines dropped-by-MD,
>   xml disabled, sequence number disabled
>   filtering disabled
> Logging to 10.0.8.12  (udp port 514, audit disabled,
>   link up),
>   435 message lines logged,
>   0 message lines rate-limited,
>   0 message lines dropped-by-MD,
>   xml disabled, sequence number disabled
>   filtering disabled
> Logging Source-Interface:   VRF Name:
> Loopback0
>
>
> I don't see any calls activity.
>
>
> thanks
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 11:19 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> But you didn't send all the information, because your output doesn't show
> the dial-peers.
>
> One method is to capture the output from "debug voip ccapi inout" and look
> for the following line "Outgoing Dial-peer="
>
> You also didn't address the regions either.  Can you send that too?
>
> On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> ------
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-s

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Region is not define in the config but CUCM. Is that what you need? That is the 
only config I have. and don't see any region defined in the gateway.


thanks

hamu



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Wednesday, February 28, 2018 11:19 AM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

But you didn't send all the information, because your output doesn't show the 
dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for 
the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice translation-profile Inbound
 translate called 1
!
voice translation-profile Strip9
 translate called 10
!
voice translation-profile block_profile
 translate calling 15
!
voice translation-profile outbound
 translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
 log config
  hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0
 shutdown
 cablelength long 0db
!
controller T1 0/1/0
 shutdown
 cablelength long 0db
!
!
!
!
!
!
interface Loopback0
 ip address 10.x.x.x 255.255.255.128
!
interface GigabitEthernet0/0
 description uplink to Lan1
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 description uplink to Lan2
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
router ospf 1
 auto-cost reference-bandwidth 1
 network 10.0.0.0 0.0.255.255 area 10.0.0.0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!


___
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

debug was turned on as shown below.


1#debug voice ccapi inout
voip ccapi inout debugging is on

made test calls and then show log, I see below output.

1#show log
Syslog logging: enabled (0 messages dropped, 37 messages rate-limited, 0 
flushes, 0 overruns, xml disabled, filtering disabled)

No Active Message Discriminator.


No Inactive Message Discriminator.

Console logging: level debugging, 517 messages logged, xml disabled,
 filtering disabled
Monitor logging: level debugging, 0 messages logged, xml disabled,
 filtering disabled
Buffer logging:  level debugging, 550 messages logged, xml disabled,
filtering disabled
Exception Logging: size (4096 bytes)
Count and timestamp logging messages: disabled
Persistent logging: disabled

No active filter modules.

Trap logging: level debugging, 620 message lines logged
Logging to 10.0.7.139  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging to 10.0.8.12  (udp port 514, audit disabled,
  link up),
  435 message lines logged,
  0 message lines rate-limited,
  0 message lines dropped-by-MD,
  xml disabled, sequence number disabled
  filtering disabled
Logging Source-Interface:   VRF Name:
Loopback0


I don't see any calls activity.


thanks



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Wednesday, February 28, 2018 11:19 AM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

But you didn't send all the information, because your output doesn't show the 
dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look for 
the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway 
<avholloway+cisco-v...@gmail.com<mailto:avholloway%2bcisco-v...@gmail.com>>
Sent: Wednesday, February 28, 2018 10:45 AM

To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router
That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice trans

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

But you didn't send all the information, because your output doesn't show
the dial-peers.

One method is to capture the output from "debug voip ccapi inout" and look
for the following line "Outgoing Dial-peer="

You also didn't address the regions either.  Can you send that too?

On Wed, Feb 28, 2018 at 11:13 AM Hamu Ebiso <hebiso2...@hotmail.com> wrote:

> I was just trying to give you all the information so that you will be able
> to see the whole picture.
>
> Regarding your questions, I don't know how to check that.
>
>
> --
> *From:* Anthony Holloway <avholloway+cisco-v...@gmail.com>
> *Sent:* Wednesday, February 28, 2018 10:45 AM
>
> *To:* Hamu Ebiso
> *Cc:* cisco-voip voyp list
> *Subject:* Re: [cisco-voip] Need help configuring router for 911 with
> POTS Lines connected to FXO port on the router
> That's interesting that I asked for the dial-peer config, and you sent
> everything but.
>
> Do you know how to confirm which dial-peer the gateway is using?
>
> On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso <hebiso2...@hotmail.com>
> wrote:
>
> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
>  rule 4 /^9\(011.*\)/ /\1/
>  rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
>  translate calling 91
>  translate called 1
> !
> voice translation-profile Inbound
>  translate called 1
> !
> voice translation-profile Strip9
>  translate called 10
> !
> voice translation-profile block_profile
>  translate calling 15
> !
> voice translation-profile outbound
>  translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> license accept end user agreement
> archive
>  log config
>   hidekeys
> username admin privilege 15 password 7 105D1F0C
> username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
> !
> !
> controller T1 0/0/0
>  shutdown
>  cablelength long 0db
> !
> controller T1 0/1/0
>  shutdown
>  cablelength long 0db
> !
> !
> !
> !
> !
> !
> interface Loopback0
>  ip address 10.x.x.x 255.255.255.128
> !
> interface GigabitEthernet0/0
>  description uplink to Lan1
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> interface GigabitEthernet0/1
>  description uplink to Lan2
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> router ospf 1
>  auto-cost reference-bandwidth 1
>  network 10.0.0.0 0.0.255.255 area 10.0.0.0
> !
> ip forward-protocol nd
> !
> !
> no ip http server
> no ip http secure-server
> !
>
>
>
___
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

I was just trying to give you all the information so that you will be able to 
see the whole picture.

Regarding your questions, I don't know how to check that.



From: Anthony Holloway <avholloway+cisco-v...@gmail.com>
Sent: Wednesday, February 28, 2018 10:45 AM
To: Hamu Ebiso
Cc: cisco-voip voyp list
Subject: Re: [cisco-voip] Need help configuring router for 911 with POTS Lines 
connected to FXO port on the router

That's interesting that I asked for the dial-peer config, and you sent 
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso 
<hebiso2...@hotmail.com<mailto:hebiso2...@hotmail.com>> wrote:

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice translation-profile Inbound
 translate called 1
!
voice translation-profile Strip9
 translate called 10
!
voice translation-profile block_profile
 translate calling 15
!
voice translation-profile outbound
 translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
 log config
  hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0
 shutdown
 cablelength long 0db
!
controller T1 0/1/0
 shutdown
 cablelength long 0db
!
!
!
!
!
!
interface Loopback0
 ip address 10.x.x.x 255.255.255.128
!
interface GigabitEthernet0/0
 description uplink to Lan1
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 description uplink to Lan2
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
router ospf 1
 auto-cost reference-bandwidth 1
 network 10.0.0.0 0.0.255.255 area 10.0.0.0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!


___
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Anthony Holloway]

That's interesting that I asked for the dial-peer config, and you sent
everything but.

Do you know how to confirm which dial-peer the gateway is using?

On Wed, Feb 28, 2018 at 10:38 AM Hamu Ebiso  wrote:

> Below is gateway configuration
>
>
>
>
> isdn switch-type primary-ni
> !
> !
> trunk group FXO_EM
>  hunt-scheme sequential
>  translation-profile incoming Incoming
> !
> !
> trunk group Local
>  hunt-scheme sequential
>  translation-profile outgoing outbound
> !
> !
> trunk group LD
>  translation-profile outgoing outbound
> !
> voice-card 0
>  dspfarm
>  dsp services dspfarm
> !
> !
> voice call send-alert
> voice rtp send-recv
> !
> voice service voip
>  ip address trusted list
>   ipv4 10.170.99.12
>   ipv4 10.44.50.14
>   ipv4 10.44.50.39
>  no ip address trusted authenticate
>  clid substitute name
>  clid network-provided
>  allow-connections h323 to h323
>  allow-connections h323 to sip
>  allow-connections sip to h323
>  allow-connections sip to sip
>  redirect ip2ip
>  signaling forward unconditional
>  fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0
> fallback pass-through g711ulaw
>  no fax-relay sg3-to-g3
>  modem passthrough nse codec g711ulaw
>  sip
>   bind control source-interface Loopback0
>   bind media source-interface Loopback0
>   session transport tcp
>   min-se 360 session-expires 360
>   ds0-num
>   header-passing
>   error-passthru
>   registrar server expires max 600 min 60
>   early-offer forced
>   midcall-signaling passthru
>   no call service stop
> !
> !
> voice class uri 10 sip
>  host ipv4:10.x.x.x
>  host ipv4:10..x.x.x
>  host ipv4:10..x.x.x
> voice class codec 1
>  codec preference 1 g711ulaw
>  codec preference 2 g729r8
> !
> voice class codec 2
>  codec preference 1 g711ulaw
> !
> !
> !
> !
> voice translation-rule 1
>  rule 1 /^208343\(\)$/ /1208343\1/
> !
> voice translation-rule 9
>  rule 1 /5.../ /1208343\0/
> !
> voice translation-rule 10
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
> !
> voice translation-rule 15
> !
> voice translation-rule 30
>  rule 1 /^911/ /911/
>  rule 2 /^9911/ /911/
>  rule 4 /^9\(011.*\)/ /\1/
>  rule 9 /^9\(.*\)/ /\1/
> !
> !
> voice translation-profile Add1
>  translate calling 91
>  translate called 1
> !
> voice translation-profile Inbound
>  translate called 1
> !
> voice translation-profile Strip9
>  translate called 10
> !
> voice translation-profile block_profile
>  translate calling 15
> !
> voice translation-profile outbound
>  translate calling 10
> !
> !
> crypto pki token default removal timeout 0
> !
> !
> !
> !
> license udi pid CISCO3845-MB sn FOC123128X5
> license accept end user agreement
> archive
>  log config
>   hidekeys
> username admin privilege 15 password 7 105D1F0C
> username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
> !
> !
> controller T1 0/0/0
>  shutdown
>  cablelength long 0db
> !
> controller T1 0/1/0
>  shutdown
>  cablelength long 0db
> !
> !
> !
> !
> !
> !
> interface Loopback0
>  ip address 10.x.x.x 255.255.255.128
> !
> interface GigabitEthernet0/0
>  description uplink to Lan1
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> interface GigabitEthernet0/1
>  description uplink to Lan2
>  ip address 10.x.x.x 255.255.255.252
>  duplex auto
>  speed auto
>  media-type rj45
> !
> router ospf 1
>  auto-cost reference-bandwidth 1
>  network 10.0.0.0 0.0.255.255 area 10.0.0.0
> !
> ip forward-protocol nd
> !
> !
> no ip http server
> no ip http secure-server
> !
>
>
>
___
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip

Re: [cisco-voip] Need help configuring router for 911 with POTS Lines connected to FXO port on the router

[Hamu Ebiso]

Below is gateway configuration




isdn switch-type primary-ni
!
!
trunk group FXO_EM
 hunt-scheme sequential
 translation-profile incoming Incoming
!
!
trunk group Local
 hunt-scheme sequential
 translation-profile outgoing outbound
!
!
trunk group LD
 translation-profile outgoing outbound
!
voice-card 0
 dspfarm
 dsp services dspfarm
!
!
voice call send-alert
voice rtp send-recv
!
voice service voip
 ip address trusted list
  ipv4 10.170.99.12
  ipv4 10.44.50.14
  ipv4 10.44.50.39
 no ip address trusted authenticate
 clid substitute name
 clid network-provided
 allow-connections h323 to h323
 allow-connections h323 to sip
 allow-connections sip to h323
 allow-connections sip to sip
 redirect ip2ip
 signaling forward unconditional
 fax protocol t38 nse force version 0 ls-redundancy 0 hs-redundancy 0 fallback 
pass-through g711ulaw
 no fax-relay sg3-to-g3
 modem passthrough nse codec g711ulaw
 sip
  bind control source-interface Loopback0
  bind media source-interface Loopback0
  session transport tcp
  min-se 360 session-expires 360
  ds0-num
  header-passing
  error-passthru
  registrar server expires max 600 min 60
  early-offer forced
  midcall-signaling passthru
  no call service stop
!
!
voice class uri 10 sip
 host ipv4:10.x.x.x
 host ipv4:10..x.x.x
 host ipv4:10..x.x.x
voice class codec 1
 codec preference 1 g711ulaw
 codec preference 2 g729r8
!
voice class codec 2
 codec preference 1 g711ulaw
!
!
!
!
voice translation-rule 1
 rule 1 /^208343\(\)$/ /1208343\1/
!
voice translation-rule 9
 rule 1 /5.../ /1208343\0/
!
voice translation-rule 10
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
!
voice translation-rule 15
!
voice translation-rule 30
 rule 1 /^911/ /911/
 rule 2 /^9911/ /911/
 rule 4 /^9\(011.*\)/ /\1/
 rule 9 /^9\(.*\)/ /\1/
!
!
voice translation-profile Add1
 translate calling 91
 translate called 1
!
voice translation-profile Inbound
 translate called 1
!
voice translation-profile Strip9
 translate called 10
!
voice translation-profile block_profile
 translate calling 15
!
voice translation-profile outbound
 translate calling 10
!
!
crypto pki token default removal timeout 0
!
!
!
!
license udi pid CISCO3845-MB sn FOC123128X5
license accept end user agreement
archive
 log config
  hidekeys
username admin privilege 15 password 7 105D1F0C
username svuntbd privilege 15 secret 5 $1$vRxN$nu4JPZttcuPskPHoSdQZx.
!
!
controller T1 0/0/0
 shutdown
 cablelength long 0db
!
controller T1 0/1/0
 shutdown
 cablelength long 0db
!
!
!
!
!
!
interface Loopback0
 ip address 10.x.x.x 255.255.255.128
!
interface GigabitEthernet0/0
 description uplink to Lan1
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
interface GigabitEthernet0/1
 description uplink to Lan2
 ip address 10.x.x.x 255.255.255.252
 duplex auto
 speed auto
 media-type rj45
!
router ospf 1
 auto-cost reference-bandwidth 1
 network 10.0.0.0 0.0.255.255 area 10.0.0.0
!
ip forward-protocol nd
!
!
no ip http server
no ip http secure-server
!


___
cisco-voip mailing list
cisco-voip@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-voip