Re: [SOLVED] auto module loading with udev ?
On Wed, 22 Dec 2010 22:01:07 -0800 bri...@aracnet.com wrote: This will give you the /dev/pilot symlink which is very handy. I already had this, in fact it may eve be in the /lib/udev/rules.d/ SUBSYSTEMS==usb, KERNEL==ttyUSB*, \ ATTRS{product}==Palm Handheld*|Handspring Visor|palmOne Handheld, \ SYMLINK+=pilot The following provides, and removes, the module automagically. The key is to match the add udev action (?): SUBSYSTEMS==usb, ACTION==add, \ ATTRS{product}==Palm Handheld*|Handspring Visor|palmOne Handheld, \ RUN+=/sbin/modprobe visor SUBSYSTEMS==usb, ACTION==remove, \ ATTRS{product}==Palm Handheld*|Handspring Visor|palmOne Handheld, \ RUN+=/sbin/modprobe -r visor Got all that useful info courtesy of the following web-page, and I used it verbatim. http://math.umh.ac.be/an/D830/ Bonus! the page talks about using Debian :-) All of this would be a whole lot easier if there was some sort of trace that tells you what udev is doing, verbosely. udevadm monitor isn't that useful. Brian -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of unsubscribe. Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/20101223141955.1a0f2...@windy.deldotd.com
auto module loading with udev ?
Hi, Palm TX support is busted in that the visor module is never loaded automagically, and it takes more googling than you would think to find out that you need the visor module. so I'd like to set up udev to do the right thing, which I have done for other devices. However I have not had to load modules as part of the set-up. Looks as though I need to maybe brute force it with PROGRAM to do a modprobe ? That seems way to klunky for a problem that had to be solved at the time udev was invented. The other possibilty is using RUN, which what the rules in /lib/udev seem to do. suggestions ? Thanks, Brian -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of unsubscribe. Trouble? Contact listmas...@lists.debian.org Archive: http://lists.debian.org/2010120107.2b8d6...@windy.deldotd.com
problem with module loading in etch
I have a bttv card etch loads driver for it during booting but etch does not use correct options so I have to use commands below: rmmod bttv modprobe bttv card=8 I add bttv card=8 to /etc/modules but it does not help. My question is how to help etch use correct options so that I needn't enter the 2 commands every time I boot etch. -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of unsubscribe. Trouble? Contact listmas...@lists.debian.org
problem with module loading in etch
I have a bttv card etch loads driver for it during booting but etch does not use correct options so I have to use commands below: rmmod bttv modprobe bttv card=8 I add bttv card=8 to /etc/modules but it does not help. My question is how to help etch use correct options so that I needn't enter the 2 commands every time I boot etch. -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of unsubscribe. Trouble? Contact listmas...@lists.debian.org
Re: problem with module loading in etch
On Fri, Mar 27, 2009 at 04:25:40PM -0400, Long Wind wrote: I have a bttv card etch loads driver for it during booting but etch does not use correct options so I have to use commands below: rmmod bttv modprobe bttv card=8 I add bttv card=8 to /etc/modules but it does not help. My question is how to help etch use correct options so that I needn't enter the 2 commands every time I boot etch. I would put something into /etc/modprobe.d/bttv like options bttv card=8 then do a update-initramfs -- It's unacceptable to think that there's any kind of comparison between the behavior of the United States of America and the action of Islamic extremists who kill innocent women and children to achieve an objective. - George W. Bush 09/15/2006 Washington, DC White House Press Conference signature.asc Description: Digital signature
Re: problem with module loading in etch
On Fri,27.Mar.09, 05:42:32, Long Wind wrote: I have a bttv card etch loads driver for it during booting but etch does not use correct options so I have to use commands below: rmmod bttv modprobe bttv card=8 I add bttv card=8 to /etc/modules but it does not help. My question is how to help etch use correct options so that I needn't enter the 2 commands every time I boot etch. Create a file (for example 00local.conf) in /etc/modprobe.d/ and put options bttv card=8 in it. Regards, Andrei -- If you can't explain it simply, you don't understand it well enough. (Albert Einstein) signature.asc Description: Digital signature
Re: problem with module loading in etch
Thanks! I'll try your solutions later on. On Fri, Mar 27, 2009 at 4:53 PM, Alex Samad a...@samad.com.au wrote: On Fri, Mar 27, 2009 at 04:25:40PM -0400, Long Wind wrote: I have a bttv card etch loads driver for it during booting but etch does not use correct options so I have to use commands below: rmmod bttv modprobe bttv card=8 I add bttv card=8 to /etc/modules but it does not help. My question is how to help etch use correct options so that I needn't enter the 2 commands every time I boot etch. I would put something into /etc/modprobe.d/bttv like options bttv card=8 then do a update-initramfs -- It's unacceptable to think that there's any kind of comparison between the behavior of the United States of America and the action of Islamic extremists who kill innocent women and children to achieve an objective. - George W. Bush 09/15/2006 Washington, DC White House Press Conference -BEGIN PGP SIGNATURE- Version: GnuPG v1.4.9 (GNU/Linux) iEYEARECAAYFAknNPMAACgkQkZz88chpJ2ODiwCfYqCey05AEVj+vrcNDDC5LlfV evYAoLuyfJOJ8jXwly054sD8g0lgOzdZ =tPyr -END PGP SIGNATURE- -- To UNSUBSCRIBE, email to debian-user-requ...@lists.debian.org with a subject of unsubscribe. Trouble? Contact listmas...@lists.debian.org
Module loading at boot (was re: setting up an encrypted filesystem..)
On Thu, Apr 27, 2006 at 08:02:48AM -0400, Roberto C. Sanchez wrote: Digby Tarvin wrote: ... But I have no idea why the '.load' suffixes - and it would appear that the system doesn't know either, because all it does is produce a series of 'FATAL' messages on the console during boot... Does anyone know of a reason for this? Or is this something that should go into a bug report to the install people? Check the current bug reports against the installer (I think it is a pseudo-package). If it is not already reported, consider filing a detailed bug report. What they likely want to know is: - How exactly you installed (e.g., what options you chose, etc) - What config changes you made after install - What version of the d-i (e.g., release number or dailiy build) - Exact error messages you receive on boot I did submit an installation report which described all the things which didn't work during or immediately after the install. But that was before I had worried about any of the benign problems that don't seem to do any harm, but are redundent or innefective. I'll send in another report. There are a couple of other ugly error message during boot which it would be nice to get cleaned up, like a bunch of: skipping already loaded module messages, and other things which flash by to fast to see. Does anyone know if there is a way to capture all of the console messages that are displayed during boot? Dmesg is only a subset, and I can't see anything else in /var/log. I don't really want to compile a kernel with a serial console because then it would no longer be the unmodified results of the install that I would be looking at. And more importantly, the only serial port that I have is a USB serial adapter, and I am not sure that a serial console could use that Regards, DigbyT -- Digby R. S. Tarvin digbyt(at)digbyt.com http://www.digbyt.com -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Module loading at boot (was re: setting up an encrypted filesystem..)
Digby Tarvin wrote: [...] Does anyone know if there is a way to capture all of the console messages that are displayed during boot? [...] Enable boot logging in /etc/default/bootlogd -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Module loading at boot (was re: setting up an encrypted filesystem..)
On Thu, Apr 27, 2006 at 09:24:52PM -0500, Mumia W wrote: Digby Tarvin wrote: [...] Does anyone know if there is a way to capture all of the console messages that are displayed during boot? [...] Enable boot logging in /etc/default/bootlogd That seems to do the trick - thanks. Regards, DigbyT -- Digby R. S. Tarvin digbyt(at)digbyt.com http://www.digbyt.com -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Question about module loading from floppy
Hello, I have to start a machine with rescue CD because lilo is broken. (I probably just have to run /sbin/lilo as root to correct this) The problem is that booting with rescue root=/dev/sda1 won't work because my drive is a RAID-5 and I need to load an extra-module to make it work. I have this module on floppy, however. How can I tell Debian to load the module from /dev/fd0 before trying to mount root FS ? Thanks for any help ! -- Marc
Re: Question about module loading from floppy
On Fri, Dec 23, 2005 at 12:08:30PM +0100, Marc Demlenne wrote: Your Debian CD 1, for instance, is a rescue CD as well... Juste take a look at the help, and try with rescue as boot image. That was the case with woody. But I hadn't found it to be true with the sarge netinstall -- perhaps I just have too old a copy of sarge? I'll try download a new one. -- hendrik On 23/12/05, [EMAIL PROTECTED] [EMAIL PROTECTED] wrote: On Fri, Dec 23, 2005 at 01:02:50AM +0100, Marc Demlenne wrote: Hello, I have to start a machine with rescue CD because lilo is broken. (I probably just have to run /sbin/lilo as root to correct this) The problem is that booting with rescue root=/dev/sda1 won't work because my drive is a RAID-5 and I need to load an extra-module to make it work. In the last few days I've heard about the so-called rescue CD. Where do I get one? My installation disks don't seem to have one. Have I got the wrong version or something? -- hendrik -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Question about module loading from floppy
On Friday, 23 December 2005 at 14:13:19 +0100, Marc Demlenne wrote: Hello, I have to start a machine with rescue CD because lilo is broken. (I probably just have to run /sbin/lilo as root to correct this) The problem is that booting with rescue root=/dev/sda1 won't work because my drive is a RAID-5 and I need to load an extra-module to make it work. I have this module on floppy, however. How can I tell Debian to load the module from /dev/fd0 before trying to mount root FS ? IMHO nobody should be without a live CD such as Knoppix or Mepis or DSL or... See http://www.frozentech.com/content/livecd.php for a more complete list. Download one and boot from that. Then mount the partition on which your root filesystem is located and copy what you need, do any necessary configuration (chroot into the mount if necessary). -- richard -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Question about module loading from floppy
Hello, I have to start a machine with rescue CD because lilo is broken. (I probably just have to run /sbin/lilo as root to correct this) The problem is that booting with rescue root=/dev/sda1 won't work because my drive is a RAID-5 and I need to load an extra-module to make it work. I have this module on floppy, however. How can I tell Debian to load the module from /dev/fd0 before trying to mount root FS ? Thanks for any help ! -- Marc
Re: Question about module loading from floppy
On Fri, Dec 23, 2005 at 01:02:50AM +0100, Marc Demlenne wrote: Hello, I have to start a machine with rescue CD because lilo is broken. (I probably just have to run /sbin/lilo as root to correct this) The problem is that booting with rescue root=/dev/sda1 won't work because my drive is a RAID-5 and I need to load an extra-module to make it work. In the last few days I've heard about the so-called rescue CD. Where do I get one? My installation disks don't seem to have one. Have I got the wrong version or something? -- hendrik -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
How to disable module loading during bootup
Hi guys, I'm new to Debian, I've just installed Debian using sarge debian-installer rc2 cd and upgrade to Sid. I need to disable my TV Tuner card (bttv) during bootup but don't know how to, I've already tried from /etc/modutils/actions by putting # in front of the post-install and post-remove : # Special actions that are needed for some modules # The BTTV module does not load the tuner module automatically, # so do that in here #post-install bttv insmod tuner #post-remove bttv rmmod tuner and /etc/discover.conf and put skip bttv but it doesn't work, the bttv modules keep loading during bootup. Please advise. Regards, Han Lin -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: How to disable module loading during bootup
Hello Han Lin ([EMAIL PROTECTED]) wrote: I'm new to Debian, I've just installed Debian using sarge debian-installer rc2 cd and upgrade to Sid. I need to disable my TV Tuner card (bttv) during bootup but don't know how to, I've already tried from /etc/modutils/actions by putting # in front of the post-install and post-remove : If you use kernel 2.6, you need to make the changes in /etc/modprobe.d/. Try something like this: alias bttv off # Special actions that are needed for some modules # The BTTV module does not load the tuner module automatically, # so do that in here #post-install bttv insmod tuner #post-remove bttv rmmod tuner This only prevents the commands from being run when bttv is loaded, it does not prevent bttv from being loaded itself. and /etc/discover.conf and put skip bttv but it doesn't work, the bttv modules keep loading during bootup. Also tell hotplug to load it (etc/hotplug/blacklist.d/). best regards Andreas Janssen -- Andreas Janssen [EMAIL PROTECTED] PGP-Key-ID: 0xDC801674 ICQ #17079270 Registered Linux User #267976 http://www.andreas-janssen.de/debian-tipps-sarge.html -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: How to disable module loading during bootup
Hi Andreas, Thanks for the hints. Now no more bttv modules appeared in my screen but I still can see the bttv: modules loaded successfully, it's funny but nevermind, I thought it's caused my soundcard not working but actually it's not, it's the OSS driver loaded before ALSA driver. Btw, I also see a lot of pciehp, shpchp thingy with failed or error, any way to prevent them to load? Regards, Han Lin On Sat, 2005-01-01 at 14:23 +0100, Andreas Janssen wrote: Hello Han Lin ([EMAIL PROTECTED]) wrote: I'm new to Debian, I've just installed Debian using sarge debian-installer rc2 cd and upgrade to Sid. I need to disable my TV Tuner card (bttv) during bootup but don't know how to, I've already tried from /etc/modutils/actions by putting # in front of the post-install and post-remove : If you use kernel 2.6, you need to make the changes in /etc/modprobe.d/. Try something like this: alias bttv off # Special actions that are needed for some modules # The BTTV module does not load the tuner module automatically, # so do that in here #post-install bttv insmod tuner #post-remove bttv rmmod tuner This only prevents the commands from being run when bttv is loaded, it does not prevent bttv from being loaded itself. and /etc/discover.conf and put skip bttv but it doesn't work, the bttv modules keep loading during bootup. Also tell hotplug to load it (etc/hotplug/blacklist.d/). best regards Andreas Janssen -- Andreas Janssen [EMAIL PROTECTED] PGP-Key-ID: 0xDC801674 ICQ #17079270 Registered Linux User #267976 http://www.andreas-janssen.de/debian-tipps-sarge.html -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: How to disable module loading during bootup
Hello Han Lin ([EMAIL PROTECTED]) wrote: Thanks for the hints. Now no more bttv modules appeared in my screen but I still can see the bttv: modules loaded successfully, it's funny but nevermind, I thought it's caused my soundcard not working but actually it's not, it's the OSS driver loaded before ALSA driver. Make sure the latest versions of discover1, hotplug and alsa-base are installed, that should solve the problem. Btw, I also see a lot of pciehp, shpchp thingy with failed or error, any way to prevent them to load? Blacklist the modules in the hotplug configuration. best regards Andreas Janssen -- Andreas Janssen [EMAIL PROTECTED] PGP-Key-ID: 0xDC801674 ICQ #17079270 Registered Linux User #267976 http://www.andreas-janssen.de/debian-tipps-sarge.html -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Documentation about module loading in sarge/kernel2.6?
Hi there, I just got a new laptop, an Acer Aspire 1522WLMi. After installing Sarge (kernel 2.6) with the rc of the debian installer, essentials parts of the system work flawlessly and I can get my work done. However, looking at /etc/modules, I findthat it's nearly empty. But modules like r8169 (Realtek nic) are loaded and working fine. Grepping /etc, I can't find any traces of aforementioned module. So conclusion is, I've been a dumb-ass thinking that I know how modules work in sarge/kernel 2.6 Anyone care to help me out or at least point me at proper documentation? Regards, Iwan -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Documentation about module loading in sarge/kernel2.6?
Hello Iwan van der Kleyn ([EMAIL PROTECTED]) wrote: I just got a new laptop, an Acer Aspire 1522WLMi. After installing Sarge (kernel 2.6) with the rc of the debian installer, essentials parts of the system work flawlessly and I can get my work done. However, looking at /etc/modules, I findthat it's nearly empty. But modules like r8169 (Realtek nic) are loaded and working fine. Grepping /etc, I can't find any traces of aforementioned module. Most modules are loaded by discover1 or hotplug (if you use kernel 2.6). See the documentation of these packages for more information. best regards Andreas Janssen -- Andreas Janssen [EMAIL PROTECTED] PGP-Key-ID: 0xDC801674 ICQ #17079270 Registered Linux User #267976 http://www.andreas-janssen.de/debian-tipps-sarge.html -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: udev, autofs module loading
Michael wrote: Hi Michael, Hi Michael :) normally if you insert a CD a corresponding pci hotplug event should be generated and hotplug should load the right module. Check out the logfiles when inserting a CD. I've rebuilt my kernel with the pci hotplugging support and loaded the pci_hotplug, shpchp, and pciehp. But I'm still not seeing any hotplug events when I insert a cd. I'm going to recompile with all of the pci hotplugging modules -- ibm, compact, and acpi -- but I'm not optimistic as I don't have ibm, or compact hardware it's sis. On a side note: Forget about autofs and install gnome-volume-manager. It does all what you want and a lot more. Despite its name it also works flawlessly under KDE and every other DE. Just try it. Check project utopia for more information about this. I've had a little look at it but I'm not too impressed. It's doesn't unmount when things are not in use, meaning I have to unmount them manually. Also I use autofs to mount NFS shares and g-v-m doesn't does this. But saying that I do like the way that it mounts things as the user not as root meaning I can umount manually without becoming root. Maybe I need to have a look at supermount but I'm not keen on doing that (yet!) -- OoberMick Marge, you're as beautiful as Princess Leia and as smart as Yoda. -- Homer Simpson pgp0.pgp Description: PGP signature
Re: udev, autofs module loading
Michael Graham [EMAIL PROTECTED] writes: cd /mnt/cdrom works as expected and the cdrom is mounted. But if the module hasn't been loaded then this fails bash: cd: /mnt/cdrom: No such file or directory because the device /dev/hdc does not exist yet and neither hotplug nor udev creates it. Is there away around this without adding the modules to /etc/modules? From what I've read on the hotplug mailing lists, Linux is going from 'load-module-at-first-use' to 'load-module-at-first-hw-detection'. Basically, you have to load the modules for your hardware when it is first inserted (or for built in hardware, like cdrom, at bootup), because udev won't load the modules when you try to access the nodes (unlike devfs). -- John L. Fjellstad web: http://www.fjellstad.org/ Quis custodiet ipsos custodes -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
udev, autofs module loading
Does anyone use udev and autofs? If so how did you get it to work? I have the following in /etc/auto.misc cdrom-fstype=iso9660,ro,sync,nodev,nosuid :/dev/hdc udfcdrom -fstype=udf,ro,sync,nodev,nosuid :/dev/hdc floppy -fstype=vfat,sync,nodev,nosuid :/dev/fd0 usbpen -fstype=vfat,sync,nodev,nosuid :/dev/sda1 If I load the modules for say my cdrom (ide-cd) then cd /mnt/cdrom works as expected and the cdrom is mounted. But if the module hasn't been loaded then this fails bash: cd: /mnt/cdrom: No such file or directory because the device /dev/hdc does not exist yet and neither hotplug nor udev creates it. Is there away around this without adding the modules to /etc/modules? -- OoberMick Don't go around saying the world owes you a living. The world owes you nothing. It was here first. -- Mark Twain pgp0.pgp Description: PGP signature
Re: udev, autofs module loading
Michael Graham wrote: Does anyone use udev and autofs? If so how did you get it to work? I have the following in /etc/auto.misc cdrom-fstype=iso9660,ro,sync,nodev,nosuid :/dev/hdc udfcdrom -fstype=udf,ro,sync,nodev,nosuid :/dev/hdc floppy -fstype=vfat,sync,nodev,nosuid :/dev/fd0 usbpen -fstype=vfat,sync,nodev,nosuid :/dev/sda1 If I load the modules for say my cdrom (ide-cd) then cd /mnt/cdrom works as expected and the cdrom is mounted. But if the module hasn't been loaded then this fails bash: cd: /mnt/cdrom: No such file or directory because the device /dev/hdc does not exist yet and neither hotplug nor udev creates it. Is there away around this without adding the modules to /etc/modules? Hi Michael, normally if you insert a CD a corresponding pci hotplug event should be generated and hotplug should load the right module. Check out the logfiles when inserting a CD. On a side note: Forget about autofs and install gnome-volume-manager. It does all what you want and a lot more. Despite its name it also works flawlessly under KDE and every other DE. Just try it. Check project utopia for more information about this. Cheers, Michael -- E-Mail: [EMAIL PROTECTED] WWW: http://www.teco.edu/ TecO (Telecooperation Office) Vincenz-Priessnitz-Str.1 University of Karlsruhe 76131 Karlsruhe, Germany -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Module loading problem
Hello list, I use Debian woody and try to get a module working ... without success :-( I've compiled DRBD (does RAID-1 over IP network) and this gone fine and smoothly. The module drbd.o was installed, however I can't use modprobe drbd but insmod drbd works, output: Using /lib/modules/block/drbd.o (I have copied the module to this place, because I watched insmod's behaviour with strace. Before that insmod did not found the module, too). I've created a file drbd in /etc/modutils, then update-modules and then again modprobe drbd. Result: modprobe hangs and did never return ... Can anybody help how to say modprobe to load the module properly? Thanks a lot! -- Best regards, Andreas Semt -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Module loading problem
Andreas Semt wrote: Hello list, I use Debian woody and try to get a module working ... without success :-( I've compiled DRBD (does RAID-1 over IP network) and this gone fine and smoothly. The module drbd.o was installed, however I can't use modprobe drbd but insmod drbd works, output: Using /lib/modules/block/drbd.o (I have copied the module to this place, because I watched insmod's behaviour with strace. Before that insmod did not found the module, too). I've created a file drbd in /etc/modutils, then update-modules and then again modprobe drbd. Result: modprobe hangs and did never return ... Can anybody help how to say modprobe to load the module properly? Thanks a lot! Did you run `depmod -a` after copying it to /lib/modules ? -Roberto signature.asc Description: OpenPGP digital signature
Module loading
Hi, how do we load modules at boot-time on debian? when i look at modules.conf, it says that I shouldnt edit it, and to use modconf and look at update-modules. also there are some files in /etc/modutils and is this where I should add the module specific lines? I'm trying to have 'snd-intel8x0' up after boot, and right now I modprobe snd-intel8x0. how can i get this done while the other modules are brought up? There is an alsa file in /etc/modutils which has a line alias snd-card-0 snd-intel8x0. thanks. -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: Module loading
Rajesh Menon wrote: Hi, how do we load modules at boot-time on debian? when i look at modules.conf, it says that I shouldnt edit it, and to use modconf and look at update-modules. also there are some files in /etc/modutils and is this where I should add the module specific lines? I'm trying to have 'snd-intel8x0' up after boot, and right now I modprobe snd-intel8x0. how can i get this done while the other modules are brought up? There is an alsa file in /etc/modutils which has a line alias snd-card-0 snd-intel8x0. thanks. echo snd-intel8x0 /etc/modules -Roberto signature.asc Description: OpenPGP digital signature
Re: Module loading
On Sat, 2004-01-24 at 17:24, Rajesh Menon wrote: Hi, how do we load modules at boot-time on debian? when i look at modules.conf, it says that I shouldnt edit it, and to use modconf and look at update-modules. also there are some files in /etc/modutils and is this where I should add the module specific lines? I'm trying to have 'snd-intel8x0' up after boot, and right now I modprobe snd-intel8x0. how can i get this done while the other modules are brought up? There is an alsa file in /etc/modutils which has a line alias snd-card-0 snd-intel8x0. the way i did it was by installing the following packages alsa-base alsa-utils (i am not sure which one did the job). during configuration of the package it asks me what my sound card is, (and then presumably sets up the correct module(s) in /etc/modutils) anyhow it seems very clean and straight-forward. i recommend it. :) -matt zagrabelny -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Module loading problem with 2.6.0 kernel
Hi! I've installed a 2.6.0 kernel image on my notebook which runs Debian GNU/Linux unstable. I configured the kernel in a very modular way, i.e. everything not necessary for booting is built as a module and not statically compiled into the kernel. I have installed the new modules-init-tools as well and I have added aliases to the /etc/modprobe.d/ directory and run update-modules afterwards, so that /etc/modprobe.conf reflects my setup (I think). Now, quite some modules get automatically loaded, but some don't. E.g. the sound modules got automatically loaded with the 2.4 kernel when I loaded xmms or xine. With the 2.6 kernel it doesn't. However, if I do # modprobe sound-slot-0 then it works as well. So, this proves that the alias is correctly set up. The same applies to the ethernet card module: If I load it by hand, it works, but it doesn't get automatically loaded though the alias to eth0 is correctly set up. What am I missing? TIA. -- Stefan Bellon -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
module loading errors
Hello, I recently compiled my own 2.4.18 kernel and all goes well; However, I get module errors because some modules were not compiled (instead functionality was compiled in the kernel) Which log file do I have to check for the module names which can't load? Thanks, Joris -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Re: module loading errors
On Sat, Dec 06, 2003 at 05:49:38PM +0100, Joris Huizer wrote: Hello, I recently compiled my own 2.4.18 kernel and all goes well; However, I get module errors because some modules were not compiled (instead functionality was compiled in the kernel) Which log file do I have to check for the module names which can't load? You should probably see the output in /var/log/syslog and/or /var/log/messages. See if the modules appear in /etc/modules, thats where modules you want to start on startup appear. Thanks, Joris -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED] -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Kernel versions and module loading
Hi, I have a woody laptop and upgraded the kernel to 2.4.18. The new kernel uses the yenta_socket and tulip for the ethernet card whereas with the 2.2.x kernel used the tulip_cb driver. Now if I try to boot the old kernel the network stuff won't work right. Here is what I found. The following kernel related things all have version numbers: /boot/vmlinuz-version /boot/System.map-version /boot/initrd.img-version I gather for pre file system mounted module loading e.g. ext3 /lib/modules/version It seems to me that there should be seperate /etc/modules-version files as well as that seems to be the only thing stopping seemless booting from version to version. At least at first blush. The /etc/init.d/modutils script is what loads the modules and prints the 'Calculating module dependencies' line in the boot sequence. It calls depmod -a which creates the /lib/modules/version/modules.dep file AFAIK so it understands the kernel version. Later in the script it loops through the entries in /etc/modules and calls modprobe. Couldn't this script use uname -r and then load /etc/modules-version where version comes from the uname -r output? This I think would make everything work better you could have different kernel versions and custom versions etc. work together better. Comments and suggestions welcome. Eric -- To UNSUBSCRIBE, email to [EMAIL PROTECTED] with a subject of unsubscribe. Trouble? Contact [EMAIL PROTECTED]
Module Loading at Boot
All, I have a new Sony Vaio Z505LS, which I have gotten Debian installed on. Everything works, except one thing: when I boot, the system loads the sound card modules before the Ethernet card modules, and the sound card steals the Ethernet's IRQ. This does not happen if I load the Ethernet card first. I can easily frankenstein into the init scripts the functionality that the Ethernet card gets loaded first, but I would rather know the Debian way of doing this correctly. I'm guessing it has something to do with the /etc/modules.conf setup? Btw, if anyone is interested in how I got Debian installed on this laptop, I'd be happy to write it up. The USB floppy drive makes for an interesting install, given that Debian likes a Rescue and a Root floppy, and the kernel on the Rescue floppy doesn't speak USB... Sean -- If at first the idea is not absurd, then there is no hope for it. -- Albert Einstein Sean C. Rhea | Please do not accept any email from me [EMAIL PROTECTED] | which is not digitally signed. Also, http://www.srhea.net | please sign any email you send to me. pgpm1jeya3Obw.pgp Description: PGP signature
Re: Module Loading at Boot
On Mon, Jan 08, 2001 at 10:39:25AM -0800, Sean Rhea wrote: I have a new Sony Vaio Z505LS, which I have gotten Debian installed on. Everything works, except one thing: when I boot, the system loads the sound card modules before the Ethernet card modules, and the sound card steals the Ethernet's IRQ. This does not happen if I load the Ethernet card first. I can easily frankenstein into the init scripts the functionality that the Ethernet card gets loaded first, but I would rather know the Debian way of doing this correctly. I'm guessing it has something to do with the /etc/modules.conf setup? You can define modules, which should be loaded at boot time in /etc/modules On my system the modules named there are loaded in the specified order. Btw, if anyone is interested in how I got Debian installed on this laptop, I'd be happy to write it up. The USB floppy drive makes for an interesting install, given that Debian likes a Rescue and a Root floppy, and the kernel on the Rescue floppy doesn't speak USB... Then write a report for http://www.cs.utexas.edu/users/kharker/linux-laptop/ Phil
8139too.o module loading problem
Hi, I get the following error message when trying to load the 8139too.o module. /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: symbol for parameter debug not found /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: insmod /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o failed /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: insmod 8139too failed I'm using woody, generic pentium2 based machine. I compiled the kernel the debian way cos I'm lazy. I did an upgrade on all the debs before i compiled this kernel. The network card is fine because I can still use it in mswindows. I don't know what the error mean or how to fix the problem. Can someone help me? M.
Re: 8139too.o module loading problem
On Tue, 19 Dec 2000 02:05:08 +1100, M. V. Nguyen said: Hi, I get the following error message when trying to load the 8139too.o module. /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: symbol for parameter debug not found /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: insmod /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o failed /lib/modules/2.4.0-test12/kernel/drivers/net/8139too.o: insmod 8139too failed I'm using woody, generic pentium2 based machine. I compiled the kernel the debian way cos I'm lazy. I did an upgrade on all the debs before i compiled this kernel. The network card is fine because I can still use it in mswindows. I don't know what the error mean or how to fix the problem. Can someone help me? I am using 2.2.18pre21 and was unable to to load 8139too as a module even though it was installed. So i compiled it directly into the kernel and it has been working fine since then.
Re: module loading problems
Quoting [EMAIL PROTECTED] ([EMAIL PROTECTED]): He downloaded kernel version 2.2.9. It was my first time installing a kernel and we read from various sources before he became impatient. We then did the following: tar xzf /usr/src/kernel...tar.gz . . . make menuconfig make-kpkg clean make-kpkg --revision=custom.1.0 kernel_image dpkg -i ../kernel-image..deb With the new kernel installed we get the following messages: . . . calculating module dependencies ...done loading modules: cdrom can't locate module cdrom snbfs can't locate module snbfs nfs can't locate module nfs ip_alias can't locate module ip_alias rarp can't locate module rarp cyclades can't locate module cyclades serial can't locate module serial 3c509 can't locate module 3c509 ppp /lib/modules/2.2.9/net/slhc.o unresolved symbol kmalloc_R93d4cfe6 /lib/modules/2.2.9/net/slhc.o unresolved symbol print_Rdd172261 /lib/modules/2.2.9/net/slhc.o unresolved symbol kfree_R037a0cba slhc:No such file or directory The usual reason is that you need to edit /etc/modules. When you installed, you probably loaded some modules at the appropriate stage, and this writes these module names into /etc/modules. Now you've installed a new kernel, and it has different things built in and different things compiled as modules. But when you boot up, the init.d scripts will try to modprobe or insmod all the modules listed in /etc/modules. Some may now be built in, some you may not have built, etc. It a little irrating booting and rebooting just so as to be able to read boot messages. Just press Shift-PageUp/PageDown (and don't switch VCs) to read the boot up stuff. Cheers, -- Email: [EMAIL PROTECTED] Tel: +44 1908 653 739 Fax: +44 1908 655 151 Snail: David Wright, Earth Science Dept., Milton Keynes, England, MK7 6AA Disclaimer: These addresses are only for reaching me, and do not signify official stationery. Views expressed here are either my own or plagiarised.
RE: module loading problems
if everything necessary was compiled in, could you just delete everything from /etc/modules? -Original Message- From: David Wright [mailto:[EMAIL PROTECTED] Sent: 22 May 2000 16:35 To: [EMAIL PROTECTED] Cc: debian-user@lists.debian.org Subject: Re: module loading problems Quoting [EMAIL PROTECTED] ([EMAIL PROTECTED]): He downloaded kernel version 2.2.9. It was my first time installing a kernel and we read from various sources before he became impatient. We then did the following: tar xzf /usr/src/kernel...tar.gz . . . make menuconfig make-kpkg clean make-kpkg --revision=custom.1.0 kernel_image dpkg -i ../kernel-image..deb With the new kernel installed we get the following messages: . . . calculating module dependencies ...done loading modules: cdrom can't locate module cdrom snbfs can't locate module snbfs nfs can't locate module nfs ip_alias can't locate module ip_alias rarp can't locate module rarp cyclades can't locate module cyclades serial can't locate module serial 3c509 can't locate module 3c509 ppp /lib/modules/2.2.9/net/slhc.o unresolved symbol kmalloc_R93d4cfe6 /lib/modules/2.2.9/net/slhc.o unresolved symbol print_Rdd172261 /lib/modules/2.2.9/net/slhc.o unresolved symbol kfree_R037a0cba slhc:No such file or directory The usual reason is that you need to edit /etc/modules. When you installed, you probably loaded some modules at the appropriate stage, and this writes these module names into /etc/modules. Now you've installed a new kernel, and it has different things built in and different things compiled as modules. But when you boot up, the init.d scripts will try to modprobe or insmod all the modules listed in /etc/modules. Some may now be built in, some you may not have built, etc. It a little irrating booting and rebooting just so as to be able to read boot messages. Just press Shift-PageUp/PageDown (and don't switch VCs) to read the boot up stuff. Cheers, -- Email: [EMAIL PROTECTED] Tel: +44 1908 653 739 Fax: +44 1908 655 151 Snail: David Wright, Earth Science Dept., Milton Keynes, England, MK7 6AA Disclaimer: These addresses are only for reaching me, and do not signify official stationery. Views expressed here are either my own or plagiarised. -- Unsubscribe? mail -s unsubscribe [EMAIL PROTECTED] /dev/null
Re: module loading problems
Quoting Dominic Blythe ([EMAIL PROTECTED]): if everything necessary was compiled in, could you just delete everything from /etc/modules? Yes, though the comments there might indicate some advantage in putting noauto. But I much prefer not compiling everything in. (In fact, you can't if you want certain drivers which have to be compiled as modules.) Cheers, -- Email: [EMAIL PROTECTED] Tel: +44 1908 653 739 Fax: +44 1908 655 151 Snail: David Wright, Earth Science Dept., Milton Keynes, England, MK7 6AA Disclaimer: These addresses are only for reaching me, and do not signify official stationery. Views expressed here are either my own or plagiarised.
module loading problems
I was asked by a friend to help him install debian onto one of his computers.He downloaded the programs allowing him to install the base system, which we did. We used a cdrom I Got from the book Debian GNU/linux 2.1 unleased, and installed the packages that would allow us to compile a new kernel. He downloaded kernel version 2.2.9. It was my first time installing a kernel and we read from various sources before he became impatient. We then did the following: tar xzf /usr/src/kernel...tar.gz . . . make menuconfig make-kpkg clean make-kpkg --revision=custom.1.0 kernel_image dpkg -i ../kernel-image..deb With the new kernel installed we get the following messages: . . . calculating module dependencies ...done loading modules: cdrom can't locate module cdrom snbfs can't locate module snbfs nfs can't locate module nfs ip_alias can't locate module ip_alias rarp can't locate module rarp cyclades can't locate module cyclades serial can't locate module serial 3c509 can't locate module 3c509 ppp /lib/modules/2.2.9/net/slhc.o unresolved symbol kmalloc_R93d4cfe6 /lib/modules/2.2.9/net/slhc.o unresolved symbol print_Rdd172261 /lib/modules/2.2.9/net/slhc.o unresolved symbol kfree_R037a0cba slhc:No such file or directory . . . Has any one got any idea what the problem might be ? Two questions: 1) Obviously it is to do with the loading of modules but I can't why they are being loaded they are in /lib/modules/2.2.9. It seems however that ppp has been loaded but requires slhc which has also not been located (it is also in /lib/mod..). Can anyone help. It would be nice to find out why this problem is occuring and not just reinstall everthing. I have already learnt alot searching through various archives on linux in search of a solution. 2) How can I get dmesg or some log file to save a complete list of all the messages that the kernel prints when it is booting. It a little irrating booting and rebooting just so as to be able to read boot messages. Tia T:Irvine
Re: module loading problems
Thus spake [EMAIL PROTECTED] on Sun, May 21, 2000 at 02:00:11AM CDT . . make menuconfig make-kpkg clean make-kpkg --revision=custom.1.0 kernel_image dpkg -i ../kernel-image..deb With the new kernel installed we get the following messages: Simple is best. I've never had any problems under Debian building and installing Linux kernels the 'old fashioned' way. cd /usr/src/linux make menuconfig make dep make clean make bzImage make modules make modules_install Copy the compressed kernel image from /usr/src/linux/arch/i386/boot to /boot using an appropriate name of your choice such as vmlinuz-2.2.9 (don't overwrite your old one!) Edit /etc/lilo.conf to reference your new kernel (see the man page for lilo.conf) lilo shutdown -r now After the system comes back up, as root, run depmod -a. It's probably already being run by the /etc/init.d/modutils boot script but running it again won't hurt anything, and will make sure it's done. 2) How can I get dmesg or some log file to save a complete list of all the messages that the kernel prints when it is booting. It a little irrating booting and rebooting just so as to be able to read boot messages. Ctrl-S will stop the load process and freeze your display. Ctrl-Q will restart it. This may help. I believe the scroll-lock key works as a toggle on this on current kernels. -- Lindsay Haisley | Everything works| PGP public key FMP Computer Services | if you let it | available at [EMAIL PROTECTED]|(The Roadie) | http://www.fmp.com/pubkeys http://www.fmp.com| |
Re: module loading problems
I tried depmod -a and got /lib/modules/2.2.9/fs/vfat.o:unresolved symbols /lib/modules/2.2.9/fs/msdos.o /lib/modules/2.2.9/fs/fat.o /lib/modules/2.2.9/net/eepro100.o /lib/modules/2.2.9/net/3c59x.o /lib/modules/2.2.9/net/dummy /lib/modules/2.2.9/net/bsd_comp.o /lib/modules/2.2.9/net/ibmtr.o etc etc... Maybe my friend and I will just have to try again (to recompile that is).I try to investigate this problem further b4 that though. It would be nice to know what went wrong and his computer is so sl! It takes forever to compile the kernel. Thanks for the tip viz ^s and ^q. T:Irvine At 02:37 21.5.2000 -0500, you wrote: Thus spake [EMAIL PROTECTED] on Sun, May 21, 2000 at 02:00:11AM CDT . . make menuconfig make-kpkg clean make-kpkg --revision=custom.1.0 kernel_image dpkg -i ../kernel-image..deb With the new kernel installed we get the following messages: Simple is best. I've never had any problems under Debian building and installing Linux kernels the 'old fashioned' way. cd /usr/src/linux make menuconfig make dep make clean make bzImage make modules make modules_install Copy the compressed kernel image from /usr/src/linux/arch/i386/boot to /boot using an appropriate name of your choice such as vmlinuz-2.2.9 (don't overwrite your old one!) Edit /etc/lilo.conf to reference your new kernel (see the man page for lilo.conf) lilo shutdown -r now After the system comes back up, as root, run depmod -a. It's probably already being run by the /etc/init.d/modutils boot script but running it again won't hurt anything, and will make sure it's done. 2) How can I get dmesg or some log file to save a complete list of all the messages that the kernel prints when it is booting. It a little irrating booting and rebooting just so as to be able to read boot messages. Ctrl-S will stop the load process and freeze your display. Ctrl-Q will restart it. This may help. I believe the scroll-lock key works as a toggle on this on current kernels. -- Lindsay Haisley | Everything works| PGP public key FMP Computer Services | if you let it | available at [EMAIL PROTECTED]|(The Roadie) | http://www.fmp.com/pubkeys http://www.fmp.com| |
Re: Module loading
Istvan == Kovacs Istvan [EMAIL PROTECTED] writes: Istvan Also, where is it documented how module names and devices Istvan correspond to each-other? Please point me to T relevant FM, Istvan so I can R it. In most cases (all that I care and know about), this is controlled by alias settings in modules.conf(5). For example, alias block-major-2 fd alias char-major-6lp -- Ian Zimmerman, Oakland, California, U.S.A. In his own soul a man bears the source from which he draws all his sorrows and his joys. Sophocles.
Module loading
Hello! As some of my modules still won't load on demand, yesterday evening (CET) I visited the IRC channel #debianhelp. There, someone told me that not all modules are supposed to load on demand. Sure enough, the drivers for my SCSI card, NIC, SB AWE32 won't load on demand, but work fine with modprobe. How can I tell which modules are supposed to auto-load and which are not? Also, where is it documented how module names and devices correspond to each-other? Please point me to T relevant FM, so I can R it. TIA, Kofa Homepage at http://www.math.bme.hu/~kofa - For PGP public key: send mail with the subject PGP Public Key Request or finger [EMAIL PROTECTED]
Re: After ftp upgrade of slink, module loading fails
After allowing an upgrade of slink packages without watching too closely, I then discovered that the auto loading of modules (ppp,sound,vfat) fails for all modules. I can use insmod to *manually* load these modules (in dependency order) and everything works. The modules.dep file is correct (depmod -a doesn't help), it has the right dependencies and locations. I have done nothing to the kernel; no new kernel. I booted up this morning with everything working, connected to an ftp site with dselect, allowed it to upgrade about a dozen packages, and afterword all module loading is broken. Anybody seen this? i got hit with this one too, but good, yesterday. I noticed something going to slink about modules being handled differently, but the message and the instructions flew by. Having caught that it had something to do with modules, i reinstalled modconf modutils from hamm, and seems to work again. also, it didn't merely stop at not autoloading, they didn't seem to stay properly loaded once inserted. in particular, i'd log in, insert the ppp module, log out, connect and try to start a ppp session, and the host where i was doing this would report to syslog that the kernel didn't support ppp. anyway, downgrade the two modules, and it seems to work. For that matter, putting ppp in /etc/modules still gave me the not supported problem. rick
Re: After ftp upgrade of slink, module loading fails
Richard E. Hawkins Esq. wrote: After allowing an upgrade of slink packages without watching too closely, I then discovered that the auto loading of modules (ppp,sound,vfat) fails for all modules. I can use insmod to *manually* load these modules (in dependency order) and everything works. The modules.dep file is correct (depmod -a doesn't help), it has the right dependencies and locations. I have done nothing to the kernel; no new kernel. I booted up this morning with everything working, connected to an ftp site with dselect, allowed it to upgrade about a dozen packages, and afterword all module loading is broken. Anybody seen this? i got hit with this one too, but good, yesterday. I noticed something going to slink about modules being handled differently, but the message and the instructions flew by. Having caught that it had something to do with modules, i reinstalled modconf modutils from hamm, and seems to work again. This did it; I didn't have modconf installed, but downgrading modutils solved the problem. THANK YOU. PS: The problem must have something to do with the /etc/modutils/ config files in the slink package. The /etc/modutils/ dir is a recent development isn't it? rick -- Ed C.
After ftp upgrade of slink, module loading fails
After allowing an upgrade of slink packages without watching too closely, I then discovered that the auto loading of modules (ppp,sound,vfat) fails for all modules. I can use insmod to *manually* load these modules (in dependency order) and everything works. The modules.dep file is correct (depmod -a doesn't help), it has the right dependencies and locations. I have done nothing to the kernel; no new kernel. I booted up this morning with everything working, connected to an ftp site with dselect, allowed it to upgrade about a dozen packages, and afterword all module loading is broken. Anybody seen this? -- Ed C.
Kernel and auto module loading.
I originally installed debian 1.3 stable version and enabled smbfs and rarp on install. I have recompiled the kernel to 2.0.32 and disabled these modules as they were not needed. I did the usual make dep, make clean, make zImage, make modules, make modules_install, and copied the zImage file to /boot and created a symbolic pointer /vmlinuz /boot/zImage, and reran LILO So far so good...and this works fine except... On bootup I still get loading modules smbfs, rarp plus /lib/modules/2.0.32/ivp4/rarp.0: unresolved symbol kfree_skb_R2cfc2375 /lib/modules/2.0.32/ipv4/rarp.o: unresolved symbol arp etc How do I stop the kernel from loading these modules at startup ? What haven't I done ? Thanks in advance Ian [EMAIL PROTECTED] -- E-mail the word unsubscribe to [EMAIL PROTECTED] TO UNSUBSCRIBE FROM THIS MAILING LIST. Trouble? E-mail to [EMAIL PROTECTED] .
Re: Kernel and auto module loading.
On Sun, 8 Mar 1998, Ian Perry wrote: I have recompiled the kernel to 2.0.32 and disabled these modules as they were not needed. I did the usual make dep, make clean, make zImage, make modules, make modules_install, and copied the zImage file to /boot and created a symbolic pointer /vmlinuz /boot/zImage, and reran LILO So far so good...and this works fine except... On bootup I still get loading modules smbfs, rarp plus /lib/modules/2.0.32/ivp4/rarp.0: unresolved symbol kfree_skb_R2cfc2375 /lib/modules/2.0.32/ipv4/rarp.o: unresolved symbol arp etc How do I stop the kernel from loading these modules at startup ? Just before doing the install, try moving /lib/modules/2.0.3? aside. Then do the install. Run depmod -a both before and after rebooting. You may also want to check your /etc/modules and /etc/modules.conf files to see whats being preloaded. -- Jean Pierre -- E-mail the word unsubscribe to [EMAIL PROTECTED] TO UNSUBSCRIBE FROM THIS MAILING LIST. Trouble? E-mail to [EMAIL PROTECTED] .
Re: Kernel and auto module loading.
Thanks, It was in the modules file. I had not noticed that file, and I just checked, it is nowhwere in the docs I have. There was also a lot of unused stuff in the /lib/modules/2.0.3? directory. I am beginning to realise that debian linux is not nearly as 'user unfriendly' as people make out. Ian -- From: Jean Pierre LeJacq [EMAIL PROTECTED] To: debian-user@lists.debian.org Cc: debian-user@lists.debian.org Subject: Re: Kernel and auto module loading. Date: Sunday, 8 March 1998 12:26 On Sun, 8 Mar 1998, Ian Perry wrote: I have recompiled the kernel to 2.0.32 and disabled these modules as they were not needed. I did the usual make dep, make clean, make zImage, make modules, make modules_install, and copied the zImage file to /boot and created a symbolic pointer /vmlinuz /boot/zImage, and reran LILO So far so good...and this works fine except... On bootup I still get loading modules smbfs, rarp plus /lib/modules/2.0.32/ivp4/rarp.0: unresolved symbol kfree_skb_R2cfc2375 /lib/modules/2.0.32/ipv4/rarp.o: unresolved symbol arp etc How do I stop the kernel from loading these modules at startup ? Just before doing the install, try moving /lib/modules/2.0.3? aside. Then do the install. Run depmod -a both before and after rebooting. You may also want to check your /etc/modules and /etc/modules.conf files to see whats being preloaded. -- Jean Pierre -- E-mail the word unsubscribe to [EMAIL PROTECTED] TO UNSUBSCRIBE FROM THIS MAILING LIST. Trouble? E-mail to [EMAIL PROTECTED] . -- E-mail the word unsubscribe to [EMAIL PROTECTED] TO UNSUBSCRIBE FROM THIS MAILING LIST. Trouble? E-mail to [EMAIL PROTECTED] .
Re: Kernel and auto module loading.
On Sun, 8 Mar 1998, Ian Perry wrote: Thanks, It was in the modules file. I had not noticed that file, and I just checked, it is nowhwere in the docs I have. There was also a lot of unused stuff in the /lib/modules/2.0.3? directory. I am beginning to realise that debian linux is not nearly as 'user unfriendly' as people make out. Debian does still require quite a bit of knowledge to get everything to work correctly. One thing that should make your life much simplier when recompiling the kernel is the kernel-package package. I use it exclusively since it takes care of many of these cross-dependencies. -- Jean Pierre -- E-mail the word unsubscribe to [EMAIL PROTECTED] TO UNSUBSCRIBE FROM THIS MAILING LIST. Trouble? E-mail to [EMAIL PROTECTED] .