Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
Apparently I forgot to quote the original message I was replying to. It happens in Data mode only on 6 meters. It does it with both VFOs on the same frequency (i.e. 50.276) or with one VFO a few kHz away, both VFOs in Data mode. I probably would have never noticed it had it not been for JT65 since WSJT-X always turns SPLIT on automatically and moves VFO B around depending on where you are on the waterfall. Mike, KI0HA On 11/16/2017 14:58, Nr4c wrote: What mode and frequency on VFO B AND VFO A when this occurs? Sent from my iPhone ...nr4c. bill On Nov 16, 2017, at 3:50 AM, Michael Eberlewrote: Was this issue ever resolved? I have noticed the same thing with mine although the issue does not appear to be the tuner itself, but the K3 is not transmitting any power so the tuner has nothing to work with. I am running FW version 5.60 an have this issue but only on 6 Meters. I can power up the K3 and open WSJT-X on my computer and select 6 meters which usually causes SPLIT to turn on. Hold TUNE and the TX keys and the display shows 0 power. Turn off SPLIT and it puts out power as usual. Then if I turn SPLIT back on, it will then output a carrier as usual. If SPLIT is enabled on 6 meters and you run a TX gain calibration, it will fail the calibration because the TX puts out no power. It's not a major issue but an annoyance since I tend to forget about it every time I switch from HF to 6 and try to check my antenna tuning. Thanks, Mike, KI0HA __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
What mode and frequency on VFO B AND VFO A when this occurs? Sent from my iPhone ...nr4c. bill > On Nov 16, 2017, at 3:50 AM, Michael Eberlewrote: > > Was this issue ever resolved? I have noticed the same thing with mine > although the issue does not appear to be the tuner itself, but the K3 is not > transmitting any power so the tuner has nothing to work with. I am running > FW version 5.60 an have this issue but only on 6 Meters. > > I can power up the K3 and open WSJT-X on my computer and select 6 meters > which usually causes SPLIT to turn on. Hold TUNE and the TX keys and the > display shows 0 power. Turn off SPLIT and it puts out power as usual. Then > if I turn SPLIT back on, it will then output a carrier as usual. > > If SPLIT is enabled on 6 meters and you run a TX gain calibration, it will > fail the calibration because the TX puts out no power. > > It's not a major issue but an annoyance since I tend to forget about it > every time I switch from HF to 6 and try to check my antenna tuning. > > Thanks, > Mike, KI0HA > > > > > > -- > Sent from: http://elecraft.365791.n2.nabble.com/ > __ > Elecraft mailing list > Home: http://mailman.qth.net/mailman/listinfo/elecraft > Help: http://mailman.qth.net/mmfaq.htm > Post: mailto:Elecraft@mailman.qth.net > > This list hosted by: http://www.qsl.net > Please help support this email list: http://www.qsl.net/donate.html > Message delivered to n...@widomaker.com __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
Was this issue ever resolved? I have noticed the same thing with mine although the issue does not appear to be the tuner itself, but the K3 is not transmitting any power so the tuner has nothing to work with. I am running FW version 5.60 an have this issue but only on 6 Meters. I can power up the K3 and open WSJT-X on my computer and select 6 meters which usually causes SPLIT to turn on. Hold TUNE and the TX keys and the display shows 0 power. Turn off SPLIT and it puts out power as usual. Then if I turn SPLIT back on, it will then output a carrier as usual. If SPLIT is enabled on 6 meters and you run a TX gain calibration, it will fail the calibration because the TX puts out no power. It's not a major issue but an annoyance since I tend to forget about it every time I switch from HF to 6 and try to check my antenna tuning. Thanks, Mike, KI0HA -- Sent from: http://elecraft.365791.n2.nabble.com/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html Message delivered to arch...@mail-archive.com
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
You need to make sure both VFO A B are in the same mode, else you will get N/A. Ken K3IU Steve Ellington wrote: How are you getting split in data A? When I push SPLIT I get SPL N/A. Steve N4LQ n...@carolina.rr.com - Original Message - From: Chuck - AE4CW ae...@att.net To: elecraft@mailman.qth.net Sent: Wednesday, October 07, 2009 9:30 PM Subject: [Elecraft] ATU TUNE does not work in DATA A Split mode Has anyone noticed that ATU TUNE does not work (properly) when in DATA A Split mode? The relays clatter for about three seconds but no RF is produced and no SWR reading is resolved. If I drop Split, ATU TUNE works fine. I'd appreciate if someone else could verify if their K3 is behaving the same way. FW is 03.41. Thanks. P.S. ATU TUNE Split mode works FB in AFSK A and FSK D. Split is N/A in PSK D. Chuck, AE4CW -- View this message in context: http://n2.nabble.com/ATU-TUNE-does-not-work-in-DATA-A-Split-mode-tp3785489p3785489.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Elecraft] ATU TUNE does not work in DATA A Split mode
Has anyone noticed that ATU TUNE does not work (properly) when in DATA A Split mode? The relays clatter for about three seconds but no RF is produced and no SWR reading is resolved. If I drop Split, ATU TUNE works fine. I'd appreciate if someone else could verify if their K3 is behaving the same way. FW is 03.41. Thanks. P.S. ATU TUNE Split mode works FB in AFSK A and FSK D. Split is N/A in PSK D. Chuck, AE4CW -- View this message in context: http://n2.nabble.com/ATU-TUNE-does-not-work-in-DATA-A-Split-mode-tp3785489p3785489.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
I can confirm this behavior. In Data A mode split, no (or very, very little) rf out. Exit split mode and get ~5w during tune. Also, when the TUNE (not atu tune) button is pressed, the display which normally shows swr displays -- and power reads 0.0. When you hit the tune button again to exit ERR TXG is displayed. FW 3.41. Rob NV5E Date: Wed, 7 Oct 2009 18:30:06 -0700 From: ae...@att.net To: elecraft@mailman.qth.net Subject: [Elecraft] ATU TUNE does not work in DATA A Split mode Has anyone noticed that ATU TUNE does not work (properly) when in DATA A Split mode? The relays clatter for about three seconds but no RF is produced and no SWR reading is resolved. If I drop Split, ATU TUNE works fine. I'd appreciate if someone else could verify if their K3 is behaving the same way. FW is 03.41. Thanks. P.S. ATU TUNE Split mode works FB in AFSK A and FSK D. Split is N/A in PSK D. Chuck, AE4CW -- View this message in context: http://n2.nabble.com/ATU-TUNE-does-not-work-in-DATA-A-Split-mode-tp3785489p3785489.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html _ Hotmail: Powerful Free email with security by Microsoft. http://clk.atdmt.com/GBL/go/171222986/direct/01/ __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
Chuck - AE4CW wrote: Has anyone noticed that ATU TUNE does not work (properly) when in DATA A Split mode? The relays clatter for about three seconds but no RF is produced and no SWR reading is resolved. If I drop Split, ATU TUNE works fine. I'd appreciate if someone else could verify if their K3 is behaving the same way. FW is 03.41. Thanks. P.S. ATU TUNE Split mode works FB in AFSK A and FSK D. Split is N/A in PSK D. Chuck, AE4CW I see it too on 3.41 Tried 3.23 just for fun, same thing. 73, Bill N2BC __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Elecraft] ATU TUNE does not work in DATA A Split mode
How are you getting split in data A? When I push SPLIT I get SPL N/A. Steve N4LQ n...@carolina.rr.com - Original Message - From: Chuck - AE4CW ae...@att.net To: elecraft@mailman.qth.net Sent: Wednesday, October 07, 2009 9:30 PM Subject: [Elecraft] ATU TUNE does not work in DATA A Split mode Has anyone noticed that ATU TUNE does not work (properly) when in DATA A Split mode? The relays clatter for about three seconds but no RF is produced and no SWR reading is resolved. If I drop Split, ATU TUNE works fine. I'd appreciate if someone else could verify if their K3 is behaving the same way. FW is 03.41. Thanks. P.S. ATU TUNE Split mode works FB in AFSK A and FSK D. Split is N/A in PSK D. Chuck, AE4CW -- View this message in context: http://n2.nabble.com/ATU-TUNE-does-not-work-in-DATA-A-Split-mode-tp3785489p3785489.html Sent from the Elecraft mailing list archive at Nabble.com. __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ Elecraft mailing list Home: http://mailman.qth.net/mailman/listinfo/elecraft Help: http://mailman.qth.net/mmfaq.htm Post: mailto:Elecraft@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html