Re: [Emc-users] Hostmot drivers
On 4/6/15 11:05 AM, Eric H. Johnson wrote: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-=-== =- un hostmot2-firmware none (no description available) ii hostmot2-firmware-7i43-2 0.8.13.g3e60a9b HostMot2 firmware images for Mesa 7i43-2 Ok, so that shows you still have version 0.8.13 of the hostmot2-firmware-7i43-2 installed, as per the prophecy. Upgrade it to 0.8.21 and see how you do. sudo apt-get -uV upgrade hostmot2-firmware-7i43-2 -- Sebastian Kuzminsky -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
I take it that you got the 7I80 running then. -- Original Message -- From: Rick r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831
Re: [Emc-users] PNCConf setup
On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 13:48:31 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Marius Liebenberg mar...@mastercut.co.za, Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. if you have similar configurations, globally replacing 5i23 with 7i80 is 99% of the change On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list
Re: [Emc-users] PNCConf setup
I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2
Re: [Emc-users] Hostmot drivers
On Monday 06 April 2015 13:05:19 Eric H. Johnson wrote: Sebastian, The command as written says no matching files, if I remove the '\', I get: I wonder where that \ came from? It is not there in my copy of the msg. Desired=Unknown/Install/Remove/Purge/Hold Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Tri g-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) | ||/ Name Version Description +++-=- == =- un hostmot2-firmware none (no description available) ii hostmot2-firmware-7i43-2 0.8.13.g3e60a9b HostMot2 firmware images for Mesa 7i43-2 The files I have under lib/firmware/hm2/7i43-2/ are: total 444 -rw-r--r-- 1 root root 131022 2014-07-24 14:21 SV8.BIT -rw-r--r-- 1 root root 16573 2014-07-24 14:21 SV8.xml -rw-r--r-- 1 root root 131022 2014-07-24 14:21 SVST4_4.BIT -rw-r--r-- 1 root root 16917 2014-07-24 14:21 SVST4_4.xml -rw-r--r-- 1 root root 131022 2014-07-24 14:21 TPEN4_5.BIT -rw-r--r-- 1 root root 16490 2014-07-24 14:21 TPEN4_5.xml Regards, Eric I think you missed upgrading the hostmot2-firmware-7i43-2 package, because the symlink is there on my machine: ls -l /lib/firmware/hm2/7i43/SVST4_4S.BIT lrwxrwxrwx 1 root root 21 Apr 6 08:58 /lib/firmware/hm2/7i43/SVST4_4S.BIT - ../7i43-2/SVST4_4.BIT dpkg -S /lib/firmware/hm2/7i43/SVST4_4S.BIT hostmot2-firmware-7i43-2: /lib/firmware/hm2/7i43/SVST4_4S.BIT dpkg -s hostmot2-firmware-7i43-2 | grep Vers Version: 0.8.21.g5be856c What is the complete output of dpkg -l hostmot2\*? -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Cheers, Gene Heskett -- There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order. -Ed Howdershelt (Author) Genes Web page http://geneslinuxbox.net:6309/gene -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] Backlash - what are ok numbers?
Hi all; Finally fixed the Oldham couplers for my X/Y axes on my latest build, and was measuring backlash for inserting in the LinuxCNC ini file. This is for a G0704 style of mill conversion, using one of those kits from the old KeilingCNC place. X/Y/Z is 0.1mm, 0.24mm 0.1mm or, 2.5 thou, 9 thou, 2.5 thou. Is this considered ok or out of range? I've put these figures in my mill ini file, and it's currently running the X and Y axes back and forth; will measure it again after a bit of wearing in. Any thoughts/comments? (as an aside, Andy Pugh's feedback for spindle soft-gearing works a treat - thank you again Andy) John. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
On the topic of the 7i80, I am actually doing two machines at once, both nearly identical, the second is about 10 miles down the road though, for a good friend of our shop, and I have done a carbon copy build on both machines. My question is, if the guy at the other shop doesn't have a wireless access point in his shop, is there any way to use the 7i80 along side his LAN ? Or do I need to just do a fresh pull before getting rolling on the programming of the control, and not worry about having a network connection after I get the 7i80 connected and operating? Rick On 4/6/2015 1:52 PM, Marius Liebenberg wrote: I take it that you got the 7I80 running then. -- Original Message -- From: Rick r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net
Re: [Emc-users] PNCConf setup
Not yet, I couldn't remember where I left off, three months ago now, with programming and setup, so I yanked the hard drive, brought in the office, gave it the DBAN treatment, and started over this morning. I am trying to get my HAL and INI files roughed out before I get real involved at the machine itself. It's just a matter of throwing the hard drive back in and turning the power on, all of the wiring and such is done on the machine, now just programming. Rick On 4/6/2015 1:52 PM, Marius Liebenberg wrote: I take it that you got the 7I80 running then. -- Original Message -- From: Rick r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Backlash - what are ok numbers?
I personally wouldn't think 0.0025 isn't horrible, but the .009 is a little high, but depending on the machine size, it might really not matter. On our machines, that would be problematic, due to the crosslides weighing 3000-4000 lbs, (on the light side depending on the machine, 10,000 on one of ours) so trying to keep track of all that mass with almost 10 thou worth of lash would make it awful rough on the ball screw and servo. Rick On 4/6/2015 2:12 PM, John Alexander Stewart wrote: Hi all; Finally fixed the Oldham couplers for my X/Y axes on my latest build, and was measuring backlash for inserting in the LinuxCNC ini file. This is for a G0704 style of mill conversion, using one of those kits from the old KeilingCNC place. X/Y/Z is 0.1mm, 0.24mm 0.1mm or, 2.5 thou, 9 thou, 2.5 thou. Is this considered ok or out of range? I've put these figures in my mill ini file, and it's currently running the X and Y axes back and forth; will measure it again after a bit of wearing in. Any thoughts/comments? (as an aside, Andy Pugh's feedback for spindle soft-gearing works a treat - thank you again Andy) John. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, Looks like it got it. Thanks much, Eric Ok, so that shows you still have version 0.8.13 of the hostmot2-firmware-7i43-2 installed, as per the prophecy. Upgrade it to 0.8.21 and see how you do. sudo apt-get -uV upgrade hostmot2-firmware-7i43-2 -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Backlash - what are ok numbers?
On Monday 06 April 2015 14:12:31 John Alexander Stewart wrote: Hi all; Finally fixed the Oldham couplers for my X/Y axes on my latest build, and was measuring backlash for inserting in the LinuxCNC ini file. This is for a G0704 style of mill conversion, using one of those kits from the old KeilingCNC place. X/Y/Z is 0.1mm, 0.24mm 0.1mm or, 2.5 thou, 9 thou, 2.5 thou. The 2.5 thou is a bit loose, bigger balls in the nut perhaps? The 9 thou Y indicates either the thrust bearing at the solidly anchored end of the screw is duff, or perhaps not properly assembled. I was able to fix one of those in a cheap 16mmx5 Chinese screw on my toy lathes z by padding the outer ring separation with some half thou alu foil shims. Several of them stacked. Tricky to cut too. Seems to be holding up so far. Is this considered ok or out of range? I've put these figures in my mill ini file, and it's currently running the X and Y axes back and forth; will measure it again after a bit of wearing in. Any thoughts/comments? (as an aside, Andy Pugh's feedback for spindle soft-gearing works a treat - thank you again Andy) John. Let us know what you found John, it helps the next person with a similar problem. Cheers, Gene Heskett -- There are four boxes to be used in defense of liberty: soap, ballot, jury, and ammo. Please use in that order. -Ed Howdershelt (Author) Genes Web page http://geneslinuxbox.net:6309/gene -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
I should be able to run the mesaflash utility from my home directory, as long as the .bit file is in that directory correct? Also, I don't have to do anything jumper wise to make this happen do I? I tried running running the mesaflash --device 7i80 --write 7i80hd_16_rmesvss6_6.bit and all I get is No 7i80 board found I have not tried to do anything with the IP address yet. Be back at it in the morning, but will be checking email this evening, Thanks Rick -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
I would get one machine running first and it would be a machine with network access. I tried to get the 7i80 working with only one network card and it gave lot of trouble. I then installed a second network connection and made it exclusive to Hostmot2. Then things started working. You must also make sure that you have the very latest firmware in the 7i80. -- Original Message -- From: Rick Lair r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 20:13:27 Subject: Re: [Emc-users] PNCConf setup On the topic of the 7i80, I am actually doing two machines at once, both nearly identical, the second is about 10 miles down the road though, for a good friend of our shop, and I have done a carbon copy build on both machines. My question is, if the guy at the other shop doesn't have a wireless access point in his shop, is there any way to use the 7i80 along side his LAN ? Or do I need to just do a fresh pull before getting rolling on the programming of the control, and not worry about having a network connection after I get the 7i80 connected and operating? Rick On 4/6/2015 1:52 PM, Marius Liebenberg wrote: I take it that you got the 7I80 running then. -- Original Message -- From: Rick r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166
Re: [Emc-users] PNCConf setup
On Mon, 6 Apr 2015, Rick Lair wrote: Date: Mon, 06 Apr 2015 15:29:04 -0400 From: Rick Lair r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Subject: Re: [Emc-users] PNCConf setup I should be able to run the mesaflash utility from my home directory, as long as the .bit file is in that directory correct? You should not need to do this as the 7I80HD already has appropriate firmware installed Also, I don't have to do anything jumper wise to make this happen do I? I tried running running the mesaflash --device 7i80 --write 7i80hd_16_rmesvss6_6.bit and all I get is No 7i80 board found I have not tried to do anything with the IP address yet. The IP address and network connection must be correct or nothing will happen The 7I80 has 3 possible IP addresses 1. 192.168.1.121 (W1 and W2 down) 2. from EEPROM (W1 down W2 up) 3. from bootps (W1 up W2 down) Default is the 192.168.1.121 address. This allows access to the card regardless of EEPROM settings. Mesaflash uses this default address if no IP address is specified on the command line. I would suggest that the EEPROM address be used for linuxcnc use and it be set for 10.10.10.10 Then you setup the RT Ethernet connection with a host address of say 10.10.10.1,netmask 255.255.255.0 and manual (no auto/dhcp) Be back at it in the morning, but will be checking email this evening, Thanks Rick -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
On Mon, 6 Apr 2015, Rick Lair wrote: Date: Mon, 06 Apr 2015 14:13:27 -0400 From: Rick Lair r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Marius Liebenberg mar...@mastercut.co.za, Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Subject: Re: [Emc-users] PNCConf setup On the topic of the 7i80, I am actually doing two machines at once, both nearly identical, the second is about 10 miles down the road though, for a good friend of our shop, and I have done a carbon copy build on both machines. My question is, if the guy at the other shop doesn't have a wireless access point in his shop, is there any way to use the 7i80 along side his LAN ? Or do I need to just do a fresh pull before getting rolling on the programming of the control, and not worry about having a network connection after I get the 7i80 connected and operating? Its a pain to deal with network issues unless you have 2 LAN connections. If you dont have wireless, one option is to install a LAN card for the real time interface (a Realtek 8139 card works well). Another option is to use a USB-- Ethernet adapter for the non-realtime (internet) connection Rick On 4/6/2015 1:52 PM, Marius Liebenberg wrote: I take it that you got the 7I80 running then. -- Original Message -- From: Rick r...@superiorroll.com To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 19:48:31 Subject: Re: [Emc-users] PNCConf setup I think I am going to try to start with just the base INI and the main stuff normally towards the top of the HAL file, temporarily deleting all pin associated verbage, start-up linux, then look at the pin names in the hal show to see what I am dealing with. On 4/6/2015 1:44 PM, Marius Liebenberg wrote: That is about right Rick. -- Original Message -- From: Rick r...@superiorroll.com To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Sent: 2015-04-06 18:58:51 Subject: Re: [Emc-users] PNCConf setup I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street
Re: [Emc-users] Backlash - what are ok numbers?
On 04/06/2015 12:29 PM, Gene Heskett wrote: On Monday 06 April 2015 14:12:31 John Alexander Stewart wrote: Hi all; Finally fixed the Oldham couplers for my X/Y axes on my latest build, and was measuring backlash for inserting in the LinuxCNC ini file. This is for a G0704 style of mill conversion, using one of those kits from the old KeilingCNC place. X/Y/Z is 0.1mm, 0.24mm 0.1mm or, 2.5 thou, 9 thou, 2.5 thou. The 2.5 thou is a bit loose, bigger balls in the nut perhaps? The 9 thou Y indicates either the thrust bearing at the solidly anchored end of the screw is duff, or perhaps not properly assembled. I was able to fix one of those in a cheap 16mmx5 Chinese screw on my toy lathes z by padding the outer ring separation with some half thou alu foil shims. Several of them stacked. Tricky to cut too. Seems to be holding up so far. Is this considered ok or out of range? I've put these figures in my mill ini file, and it's currently running the X and Y axes back and forth; will measure it again after a bit of wearing in. Any thoughts/comments? (as an aside, Andy Pugh's feedback for spindle soft-gearing works a treat - thank you again Andy) John. Let us know what you found John, it helps the next person with a similar problem. Cheers, Gene Heskett I've been dealing with a loose Y axis on my cinci contourmaster; this machine is set up so one can turn either the ballscrew or the servo motor to adjust position. The so-called lock on the servo end was loose and so the backlash was self-adjusting;out to unusable amounts. Ugh. I'm in the process of a dual fix ... complete rebuild the mount for the ballscrew so I can lock it down tight and add a 10 5 um glass scale for reference. For now I will connect just the glass scale with it's attendant tuning problems (just not quite enough counts) but the future holds a config where P and D are fed from a 40K count/in encoderon the ballscrew and I is driven by the glass scale in like manner to Stu's big machine. Some years ago I was asked to fab a bunch of blocks for a US First robotics team. Set them up and ran as a batch. When finished I miked them to see how I'd done. SD was 0.001 but the dimensions were all large by about 2 thou. This on a machine (mazak) with 0.0025 backlash on both X and Y. Appropriate cutter comp might have landed these in the right range if it made a difference. ;-) Just personal experience. Dave -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] Hostmot drivers
Hi all, I am running into a problem with installing the hostmot drivers that I do not recall encountering before. I installed the 7i43-small packages, then just tried to run the hm2_servo | 7i43-small sample configuration, telling it to make a local copy. It tells me it cannot find SVST4_4S.BIN. There is no SVST4_4S.BIN under /lib/firmware., only SVST4_4.BIN. I made a local copy of SVST4_4.BIN in /linuxcnc/configs/hm2-servo, and changed the ini file to reference SVST4_4.BIN. Still says it cannot find the file, and is looking in path hm2/7i43/SVST4_4.BIN. I am not sure what that is referenced to, but recreated the path under linuxcnc/config and several other places. I am running lcnc 2.5.4. What stupid thing am I doing wrong? Thanks, Eric http://t.signalequattro.com/e1t/o/5/f18dQhb0S7ks8dDMPbW2n0x6l2B9gXrN7sKj6v4 LCQRN7fcnk8RJ6s6N8rBF7Rd3_yKW18Chwm1k1H6H0?si=6453247850577920pi=690ed21c-6 0fc-4209-aa81-78b89ec4a709 -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
All, I should add, I am running on Xubuntu 10.04, which I have done all along because it provides a smaller foot print, and I run headless. I installed from the 10.04 script, then used Synaptic to install the hostmot package (7i43-small). Regards, Eric I am running into a problem with installing the hostmot drivers that I do not recall encountering before. I installed the 7i43-small packages, then just tried to run the hm2_servo | 7i43-small sample configuration, telling it to make a local copy. It tells me it cannot find SVST4_4S.BIN. There is no SVST4_4S.BIN under /lib/firmware., only SVST4_4.BIN. I made a local copy of SVST4_4.BIN in /linuxcnc/configs/hm2-servo, and changed the ini file to reference SVST4_4.BIN. Still says it cannot find the file, and is looking in path hm2/7i43/SVST4_4.BIN. I am not sure what that is referenced to, but recreated the path under linuxcnc/config and several other places. I am running lcnc 2.5.4. What stupid thing am I doing wrong? Thanks, Eric http://t.signalequattro.com/e1t/o/5/f18dQhb0S7ks8dDMPbW2n0x6l2B9gXrN7sKj6v4 LCQRN7fcnk8RJ6s6N8rBF7Rd3_yKW18Chwm1k1H6H0?si=6453247850577920pi=690ed21c-6 0fc-4209-aa81-78b89ec4a709 -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
On 04/06/2015 07:35 AM, Eric H. Johnson wrote: I should add, I am running on Xubuntu 10.04, which I have done all along because it provides a smaller foot print, and I run headless. I installed from the 10.04 script, then used Synaptic to install the hostmot package (7i43-small). Which version of the hostmot2 packages do you have? Find out with dpkg -l 'hostmot2*'. There was a snafu for a while with the old package compatibility symlinks, maybe something got missed. -- Sebastian Kuzminsky -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Chris, Sorry, typo. BIT. Regards, Eric Sent from Samsung Mobile Original message From: andy pugh bodge...@gmail.com Date: 06/04/2015 8:41 AM (GMT-05:00) To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net Subject: Re: [Emc-users] Hostmot drivers On 6 April 2015 at 11:33, Eric H. Johnson ejohn...@camalytics.com wrote: It tells me it cannot find SVST4_4S.BIN. .BIN or.BIT? -- atp If you can't fix it, you don't own it. http://www.ifixit.com/Manifesto -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, 0.8.13.g3e60a9b Regards, Eric Which version of the hostmot2 packages do you have? Find out with dpkg -l 'hostmot2*'. There was a snafu for a while with the old package compatibility symlinks, maybe something got missed. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
On 6 April 2015 at 11:33, Eric H. Johnson ejohn...@camalytics.com wrote: It tells me it cannot find SVST4_4S.BIN. .BIN or.BIT? -- atp If you can't fix it, you don't own it. http://www.ifixit.com/Manifesto -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, Is SVST4_4S.BIT different from SVST4_4.BIT. I assumed the 'S' meant that it was for the small (200K) FPGA. SVST4_4.BIT was the only one that installed with the 7i43-small package. If I drop the hm2/7i43/ from the path in the ini file, it still does not find the BIT file, at least any place I have tried to put it under linuxcnc or linuxcnc/config. If I add an explicit path in the ini file ( /home/...), it says file name exceeds 30 characters. Regards, Eric Which version of the hostmot2 packages do you have? Find out with dpkg -l 'hostmot2*'. There was a snafu for a while with the old package compatibility symlinks, maybe something got missed. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
On 4/6/15 9:10 AM, Eric H. Johnson wrote: Is SVST4_4S.BIT different from SVST4_4.BIT. I assumed the 'S' meant that it was for the small (200K) FPGA. SVST4_4.BIT was the only one that installed with the 7i43-small package. There are two SVST4_4 bit files, one for the 400k FPGA (big, aka B) and one for the 200k FPGA (small, aka S). The problem you describe is a bug in the hostmot2 firmware package, which i think is now fixed. It was due to a change in how/where the firmware debs package the files. It's better now, but old versions of linuxcnc don't know about the new better paths. The problem is fixed in the latest version of the hostmot2 debs by adding back the symlinks to the old firmware locations that i erroneously removed. Try 0.8.21 from the hm2 buildbot: deb http://buildbot.linuxcnc.org/hm2 hm2-firmware v0 If that works for you then i'll update the debs at www.linuxcnc.org. If I drop the hm2/7i43/ from the path in the ini file, it still does not find the BIT file, at least any place I have tried to put it under linuxcnc or linuxcnc/config. If I add an explicit path in the ini file ( /home/...), it says file name exceeds 30 characters. Yeah, firmware path lengths are quite restricted by the linux kernel. When i was originally implementing kernel firmware loading in our hostmot2 driver i asked the kernel folks to relax the path length limit so that we could have our firmwares in our home directories, but they (probably correctly) refused and told us to install them in /lib/firmware like everyone else. Which is what we do now. -- Sebastian Kuzminsky -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, Never mind, I see the apt-get update did update to version 0.8.21, but still no SVST4_4S.BIT file, and same error when I try to run referencing SVST4_4.BIT. Regards, Eric Sebastian, You mean put deb... in the sources.list file, right? I did that, and apt-get update worked fine and identified linuxcnc. Then I should do apt-get install hm2-firmware, right? It says package not found. Regards, Eric There are two SVST4_4 bit files, one for the 400k FPGA (big, aka B) and one for the 200k FPGA (small, aka S). The problem you describe is a bug in the hostmot2 firmware package, which i think is now fixed. It was due to a change in how/where the firmware debs package the files. It's better now, but old versions of linuxcnc don't know about the new better paths. The problem is fixed in the latest version of the hostmot2 debs by adding back the symlinks to the old firmware locations that i erroneously removed. Try 0.8.21 from the hm2 buildbot: deb http://buildbot.linuxcnc.org/hm2 hm2-firmware v0 If that works for you then i'll update the debs at www.linuxcnc.org. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, You mean put deb... in the sources.list file, right? I did that, and apt-get update worked fine and identified linuxcnc. Then I should do apt-get install hm2-firmware, right? It says package not found. Regards, Eric There are two SVST4_4 bit files, one for the 400k FPGA (big, aka B) and one for the 200k FPGA (small, aka S). The problem you describe is a bug in the hostmot2 firmware package, which i think is now fixed. It was due to a change in how/where the firmware debs package the files. It's better now, but old versions of linuxcnc don't know about the new better paths. The problem is fixed in the latest version of the hostmot2 debs by adding back the symlinks to the old firmware locations that i erroneously removed. Try 0.8.21 from the hm2 buildbot: deb http://buildbot.linuxcnc.org/hm2 hm2-firmware v0 If that works for you then i'll update the debs at www.linuxcnc.org. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] PNCConf setup
Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
On 4/6/15 9:59 AM, Eric H. Johnson wrote: Never mind, I see the apt-get update did update to version 0.8.21, but still no SVST4_4S.BIT file, and same error when I try to run referencing SVST4_4.BIT. I think you missed upgrading the hostmot2-firmware-7i43-2 package, because the symlink is there on my machine: ls -l /lib/firmware/hm2/7i43/SVST4_4S.BIT lrwxrwxrwx 1 root root 21 Apr 6 08:58 /lib/firmware/hm2/7i43/SVST4_4S.BIT - ../7i43-2/SVST4_4.BIT dpkg -S /lib/firmware/hm2/7i43/SVST4_4S.BIT hostmot2-firmware-7i43-2: /lib/firmware/hm2/7i43/SVST4_4S.BIT dpkg -s hostmot2-firmware-7i43-2 | grep Vers Version: 0.8.21.g5be856c What is the complete output of dpkg -l hostmot2\*? -- Sebastian Kuzminsky -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] Hostmot drivers
Sebastian, The command as written says no matching files, if I remove the '\', I get: Desired=Unknown/Install/Remove/Purge/Hold | Status=Not/Inst/Cfg-files/Unpacked/Failed-cfg/Half-inst/trig-aWait/Trig-pend |/ Err?=(none)/Reinst-required (Status,Err: uppercase=bad) ||/ Name Version Description +++-=-== =- un hostmot2-firmware none (no description available) ii hostmot2-firmware-7i43-2 0.8.13.g3e60a9b HostMot2 firmware images for Mesa 7i43-2 The files I have under lib/firmware/hm2/7i43-2/ are: total 444 -rw-r--r-- 1 root root 131022 2014-07-24 14:21 SV8.BIT -rw-r--r-- 1 root root 16573 2014-07-24 14:21 SV8.xml -rw-r--r-- 1 root root 131022 2014-07-24 14:21 SVST4_4.BIT -rw-r--r-- 1 root root 16917 2014-07-24 14:21 SVST4_4.xml -rw-r--r-- 1 root root 131022 2014-07-24 14:21 TPEN4_5.BIT -rw-r--r-- 1 root root 16490 2014-07-24 14:21 TPEN4_5.xml Regards, Eric I think you missed upgrading the hostmot2-firmware-7i43-2 package, because the symlink is there on my machine: ls -l /lib/firmware/hm2/7i43/SVST4_4S.BIT lrwxrwxrwx 1 root root 21 Apr 6 08:58 /lib/firmware/hm2/7i43/SVST4_4S.BIT - ../7i43-2/SVST4_4.BIT dpkg -S /lib/firmware/hm2/7i43/SVST4_4S.BIT hostmot2-firmware-7i43-2: /lib/firmware/hm2/7i43/SVST4_4S.BIT dpkg -s hostmot2-firmware-7i43-2 | grep Vers Version: 0.8.21.g5be856c What is the complete output of dpkg -l hostmot2\*? -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] PNCConf setup
I do have a few, 3 to be exact, running almost a carbon copy build (5i23-7i49-7i44-7i71-7i70-7i73), of what I am building now, (7i80-7i49-7i52-7i71-7i70-7i73). Would a line that looked like this before, net spindle-low-range-sol = hm2_5i23.0.7i71.0.3.output-00 Look like this with the 7i80? net spindle-low-range-sol = hm2_7i80.0.7i71.0.3.output-00 On 4/6/2015 12:05 PM, Peter C. Wallace wrote: On Mon, 6 Apr 2015, Rick wrote: Date: Mon, 06 Apr 2015 11:57:21 -0400 From: Rick r...@superiorroll.com Reply-To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net To: Emc Users emc-users@lists.sourceforge.net Subject: [Emc-users] PNCConf setup Hello Guys, What would be the closest configuration to try to build with from the PNCConf utility, I am using the 7i80HD-16 card. I know that the card is not an option yet in the utility, and just want to try to get my files roughed out with that, instead of trying to hand write my HAL file from scratch. -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com ISTR that you have a 5i23 config with a resolver, that should be a close starting point -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users Peter Wallace Mesa Electronics (\__/) (='.'=) This is Bunny. Copy and paste bunny into your ()_() signature to help him gain world domination. -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users -- Thanks Rick Lair Superior Roll Turning LLC 399 East Center Street Petersburg MI, 49270 PH: 734-279-1831 FAX: 734-279-1166 www.superiorroll.com -- BPM Camp - Free Virtual Workshop May 6th at 10am PDT/1PM EDT Develop your own process in accordance with the BPMN 2 standard Learn Process modeling best practices with Bonita BPM through live exercises http://www.bonitasoft.com/be-part-of-it/events/bpm-camp-virtual- event?utm_ source=Sourceforge_BPM_Camp_5_6_15utm_medium=emailutm_campaign=VA_SF ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
