Re: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
In message: <[EMAIL PROTECTED]> "Brian F. Feldman" <[EMAIL PROTECTED]> writes: : "Scott Penno" <[EMAIL PROTECTED]> wrote: : > I removed apm from the kernel which appeared to be playing having with acpi : > and things are now working a treat. The card works fine, however I do : > receive the following message, 'cardbus0: (vendor=0x115d, : > dev=0x0103) at 0.1 irq 5'. I've had a look through various lists and : > couldn't find a resolution. Is this a real drama and if so, how do I : > correct it? : : I believe that's the "modem" device on the card. I don't believe that it is : in fact a normal serial port in any case, so it's worth just ignoring in my : opinion. (Witness the address 0.1, where the Ethernet was probably found at : 0.0). Sound about right? It is the modem device, and it is supported by FreeBSD, modulo a few bugs in the driver attachment code at the moment. Warner To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
Re: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
"Scott Penno" <[EMAIL PROTECTED]> wrote: > I removed apm from the kernel which appeared to be playing having with acpi > and things are now working a treat. The card works fine, however I do > receive the following message, 'cardbus0: (vendor=0x115d, > dev=0x0103) at 0.1 irq 5'. I've had a look through various lists and > couldn't find a resolution. Is this a real drama and if so, how do I > correct it? I believe that's the "modem" device on the card. I don't believe that it is in fact a normal serial port in any case, so it's worth just ignoring in my opinion. (Witness the address 0.1, where the Ethernet was probably found at 0.0). Sound about right? -- Brian Fundakowski Feldman \'[ FreeBSD ]''\ <> [EMAIL PROTECTED] <> [EMAIL PROTECTED] \ The Power to Serve! \ Opinions expressed are my own. \,,\ To Unsubscribe: send mail to [EMAIL PROTECTED] with "unsubscribe freebsd-current" in the body of the message
Re: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
I removed apm from the kernel which appeared to be playing having with acpi and things are now working a treat. The card works fine, however I do receive the following message, 'cardbus0: (vendor=0x115d, dev=0x0103) at 0.1 irq 5'. I've had a look through various lists and couldn't find a resolution. Is this a real drama and if so, how do I correct it? Regards, Scott - Original Message - From: "Scott Penno" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Sent: Monday, May 06, 2002 8:54 PM Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G > Just an update. I've tried three different 32 bit cards and every time the > card was inserted the laptop locked up. I recompiled the kernel without the > miibus and dc and then inserted the Xircom card the laptop would appear to > lock up, that is, everything that was running just stopped. When the card > was re-inserted, everything would come back to life and a console message > would appear reporting 'pccbb0: Cardbus card activation failed'. A similar > result was experienced with the other cards. With that said, I'm still no > closer to identifying the cause of these problems. Any ideas? > > Scott. > > > > - Original Message - > From: "Scott Penno" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> > Sent: Sunday, May 05, 2002 12:27 AM > Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G [DRAFT] > > > > Hi there, > > > > I've been attempting to get my Xircom Realport CBEM56G working under > CURRENT > > for some time without success. I grabbed the latest source on 03/05 > 12:00PM > > GMT and compiled without a problem. I have a 3Com Etherlink III 3C589D > card > > which is a 16 bit card which I can insert and use without a problem. > > However when I try and insert my Xircom Realport CBEM56G, my laptop locks > > up. > > Under 4.X the cardbus bridge caused some intial problems getting > configured > > but once working, worked a treat and I suspect this is where the current > > problem is. Without the kernel option PCI_ALLOW_UNSUPPORTED_IO_RANGE with > > NEWCARD, I'm unable to > > acheive any card functionality, when compiled with this option the 16 bit > > 3Com card works fine but the 32bit Xircom card causes a lockup. > Interesting > > to note also that under Windows XP and FreeBSD 4.X the bridge is detected > as > > an OZ6933, while under FreeBSD 5.X it's detected as an OZ6833. > > Not sure where to go from here so any assistance appreciated. I've > included > > a dmesg from boot -v with the 3Com card, console messages when the Xircom > > card is inserted until the lockup occurs and finally the kernel > > configuration file. > > > > Regards, > > > > Scott. > > > > > > > > Copyright (c) 1992-2002 The FreeBSD Project. > > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > > The Regents of the University of California. All rights reserved. > > FreeBSD 5.0-CURRENT #2: Sat May 4 12:13:42 EST 2002 > > [EMAIL PROTECTED]:/usr/obj/usr/src/sys/JUPITER > > Preloaded elf kernel "/boot/kernel/kernel" at 0xc043b000. > > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc043b0b4. > > Calibrating clock(s) ... TSC clock: 897239123 Hz, i8254 clock: 1193138 Hz > > CLK_USE_I8254_CALIBRATION not specified - using default frequency > > Timecounter "i8254" frequency 1193182 Hz > > CLK_USE_TSC_CALIBRATION not specified - using old calibration method > > TSC initialization skipped: APM enabled. > > CPU: Pentium III/Pentium III Xeon/Celeron (897.28-MHz 686-class CPU) > > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > > > > Features=0x383f9ff > PAT,PSE36,MMX,FXSR,SSE> > > real memory = 266797056 (260544K bytes) > > Physical memory chunk(s): > > 0x1000 - 0x0009efff, 647168 bytes (158 pages) > > 0x00462000 - 0x0fe67fff, 262168576 bytes (64006 pages) > > avail memory = 254808064 (248836K bytes) > > bios32: Found BIOS32 Service Directory header at 0xc00f66b0 > > bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1 > > pcibios: PCI BIOS entry at 0xfd890+0x13a > > pnpbios: Found PnP BIOS data at 0xc00f6700 > > pnpbios: Entry = f:a2a6 Rev = 1.0 > > Other BIOS signatures found: > > null: > > random: > > mem: > > Pentium Pro MTRR support enabled > > VESA: information block > > 56 45 53 41 00 03 00 01 00 01 01 00 00 00 40 00 > > 00 01 10 00 00
Re: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
On Mon, May 06, 2002 at 08:54:01PM +1000, Scott Penno wrote: Hi, > Just an update. I've tried three different 32 bit cards and every time the > card was inserted the laptop locked up. I recompiled the kernel without the > miibus and dc and then inserted the Xircom card the laptop would appear to > lock up, that is, everything that was running just stopped. When the card > was re-inserted, everything would come back to life and a console message > would appear reporting 'pccbb0: Cardbus card activation failed'. A similar > result was experienced with the other cards. With that said, I'm still no > closer to identifying the cause of these problems. Any ideas? Well, I've used different versions of 5.0 on my laptop, and my experience is that Cardbus devices don't like to be pulled out. Everytime I've done it the system has hung, so my assumption is: Patient: When I remove a 32bit card the system freezes. Doctor: Don't remove 32bit cards. About inserting it, well, I never had success with that either. The only way for it to work is to have the card already there *before* booting the system. I don't know if that's the expected behaviour or not, it works flawlessly with 16bit stuff. My hardware is a Thinkpad 300E, a 16bit ne2k clone and a RealJunk 8139 Cardbus NIC. Cheers, -- Miguel Mendez - [EMAIL PROTECTED] GPG Public Key :: http://energyhq.homeip.net/files/pubkey.txt EnergyHQ :: http://www.energyhq.tk FreeBSD - The power to serve! msg38068/pgp0.pgp Description: PGP signature
Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G
Just an update. I've tried three different 32 bit cards and every time the card was inserted the laptop locked up. I recompiled the kernel without the miibus and dc and then inserted the Xircom card the laptop would appear to lock up, that is, everything that was running just stopped. When the card was re-inserted, everything would come back to life and a console message would appear reporting 'pccbb0: Cardbus card activation failed'. A similar result was experienced with the other cards. With that said, I'm still no closer to identifying the cause of these problems. Any ideas? Scott. - Original Message - From: "Scott Penno" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]>; <[EMAIL PROTECTED]> Sent: Sunday, May 05, 2002 12:27 AM Subject: Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G [DRAFT] > Hi there, > > I've been attempting to get my Xircom Realport CBEM56G working under CURRENT > for some time without success. I grabbed the latest source on 03/05 12:00PM > GMT and compiled without a problem. I have a 3Com Etherlink III 3C589D card > which is a 16 bit card which I can insert and use without a problem. > However when I try and insert my Xircom Realport CBEM56G, my laptop locks > up. > Under 4.X the cardbus bridge caused some intial problems getting configured > but once working, worked a treat and I suspect this is where the current > problem is. Without the kernel option PCI_ALLOW_UNSUPPORTED_IO_RANGE with > NEWCARD, I'm unable to > acheive any card functionality, when compiled with this option the 16 bit > 3Com card works fine but the 32bit Xircom card causes a lockup. Interesting > to note also that under Windows XP and FreeBSD 4.X the bridge is detected as > an OZ6933, while under FreeBSD 5.X it's detected as an OZ6833. > Not sure where to go from here so any assistance appreciated. I've included > a dmesg from boot -v with the 3Com card, console messages when the Xircom > card is inserted until the lockup occurs and finally the kernel > configuration file. > > Regards, > > Scott. > > > > Copyright (c) 1992-2002 The FreeBSD Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 5.0-CURRENT #2: Sat May 4 12:13:42 EST 2002 > [EMAIL PROTECTED]:/usr/obj/usr/src/sys/JUPITER > Preloaded elf kernel "/boot/kernel/kernel" at 0xc043b000. > Preloaded elf module "/boot/kernel/acpi.ko" at 0xc043b0b4. > Calibrating clock(s) ... TSC clock: 897239123 Hz, i8254 clock: 1193138 Hz > CLK_USE_I8254_CALIBRATION not specified - using default frequency > Timecounter "i8254" frequency 1193182 Hz > CLK_USE_TSC_CALIBRATION not specified - using old calibration method > TSC initialization skipped: APM enabled. > CPU: Pentium III/Pentium III Xeon/Celeron (897.28-MHz 686-class CPU) > Origin = "GenuineIntel" Id = 0x68a Stepping = 10 > > Features=0x383f9ff PAT,PSE36,MMX,FXSR,SSE> > real memory = 266797056 (260544K bytes) > Physical memory chunk(s): > 0x1000 - 0x0009efff, 647168 bytes (158 pages) > 0x00462000 - 0x0fe67fff, 262168576 bytes (64006 pages) > avail memory = 254808064 (248836K bytes) > bios32: Found BIOS32 Service Directory header at 0xc00f66b0 > bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1 > pcibios: PCI BIOS entry at 0xfd890+0x13a > pnpbios: Found PnP BIOS data at 0xc00f6700 > pnpbios: Entry = f:a2a6 Rev = 1.0 > Other BIOS signatures found: > null: > random: > mem: > Pentium Pro MTRR support enabled > VESA: information block > 56 45 53 41 00 03 00 01 00 01 01 00 00 00 40 00 > 00 01 10 00 00 01 31 01 00 01 43 01 00 01 5d 01 > 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 > VESA: 16 mode(s) found > VESA: v3.0, 1024k memory, flags:0x1, mode table:0xc03895c0 (140) > VESA: Intel815M(TM) Graphics Chip Accelerated VGA BIOS > VESA: Intel Corporation i815M Graphics Controller Hardware Version 0.0 > pci_open(1): mode 1 addr port (0x0cf8) is 0x80001004 > pci_open(1a): mode1res=0x8000 (0x8000) > pci_cfgcheck: device 0 [class=06] [hdr=00] is there (id=11308086) > Using $PIR table, 7 entries at 0xc00fdf50 > apm0: on motherboard > apm0: found APM BIOS v1.2, connected at v1.2 > npx0: on motherboard > npx0: INT 16 interface > acpi0: Other PM system enabled. > pcib0: at pcibus 0 on > motherboard > pci0: physical bus=0 > found-> vendor=0x8086, dev=0x1130, revid=0x11 > bus=0, slot=0, func=0 > class=06-00-00, hdrtype=0x00, mfdev=0 > map[10]: type 3, range 32, base f800, size 26, enabled > map[14]: type 1, range 32, base f400, size
Problems with Dell Inspiron 2500/NEWCARD/Xircom CBEM56G [DRAFT]
Hi there, I've been attempting to get my Xircom Realport CBEM56G working under CURRENT for some time without success. I grabbed the latest source on 03/05 12:00PM GMT and compiled without a problem. I have a 3Com Etherlink III 3C589D card which is a 16 bit card which I can insert and use without a problem. However when I try and insert my Xircom Realport CBEM56G, my laptop locks up. Under 4.X the cardbus bridge caused some intial problems getting configured but once working, worked a treat and I suspect this is where the current problem is. Without the kernel option PCI_ALLOW_UNSUPPORTED_IO_RANGE with NEWCARD, I'm unable to acheive any card functionality, when compiled with this option the 16 bit 3Com card works fine but the 32bit Xircom card causes a lockup. Interesting to note also that under Windows XP and FreeBSD 4.X the bridge is detected as an OZ6933, while under FreeBSD 5.X it's detected as an OZ6833. Not sure where to go from here so any assistance appreciated. I've included a dmesg from boot -v with the 3Com card, console messages when the Xircom card is inserted until the lockup occurs and finally the kernel configuration file. Regards, Scott. Copyright (c) 1992-2002 The FreeBSD Project. Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 The Regents of the University of California. All rights reserved. FreeBSD 5.0-CURRENT #2: Sat May 4 12:13:42 EST 2002 [EMAIL PROTECTED]:/usr/obj/usr/src/sys/JUPITER Preloaded elf kernel "/boot/kernel/kernel" at 0xc043b000. Preloaded elf module "/boot/kernel/acpi.ko" at 0xc043b0b4. Calibrating clock(s) ... TSC clock: 897239123 Hz, i8254 clock: 1193138 Hz CLK_USE_I8254_CALIBRATION not specified - using default frequency Timecounter "i8254" frequency 1193182 Hz CLK_USE_TSC_CALIBRATION not specified - using old calibration method TSC initialization skipped: APM enabled. CPU: Pentium III/Pentium III Xeon/Celeron (897.28-MHz 686-class CPU) Origin = "GenuineIntel" Id = 0x68a Stepping = 10 Features=0x383f9ff real memory = 266797056 (260544K bytes) Physical memory chunk(s): 0x1000 - 0x0009efff, 647168 bytes (158 pages) 0x00462000 - 0x0fe67fff, 262168576 bytes (64006 pages) avail memory = 254808064 (248836K bytes) bios32: Found BIOS32 Service Directory header at 0xc00f66b0 bios32: Entry = 0xfd890 (c00fd890) Rev = 0 Len = 1 pcibios: PCI BIOS entry at 0xfd890+0x13a pnpbios: Found PnP BIOS data at 0xc00f6700 pnpbios: Entry = f:a2a6 Rev = 1.0 Other BIOS signatures found: null: random: mem: Pentium Pro MTRR support enabled VESA: information block 56 45 53 41 00 03 00 01 00 01 01 00 00 00 40 00 00 01 10 00 00 01 31 01 00 01 43 01 00 01 5d 01 00 01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 VESA: 16 mode(s) found VESA: v3.0, 1024k memory, flags:0x1, mode table:0xc03895c0 (140) VESA: Intel815M(TM) Graphics Chip Accelerated VGA BIOS VESA: Intel Corporation i815M Graphics Controller Hardware Version 0.0 pci_open(1): mode 1 addr port (0x0cf8) is 0x80001004 pci_open(1a): mode1res=0x8000 (0x8000) pci_cfgcheck: device 0 [class=06] [hdr=00] is there (id=11308086) Using $PIR table, 7 entries at 0xc00fdf50 apm0: on motherboard apm0: found APM BIOS v1.2, connected at v1.2 npx0: on motherboard npx0: INT 16 interface acpi0: Other PM system enabled. pcib0: at pcibus 0 on motherboard pci0: physical bus=0 found-> vendor=0x8086, dev=0x1130, revid=0x11 bus=0, slot=0, func=0 class=06-00-00, hdrtype=0x00, mfdev=0 map[10]: type 3, range 32, base f800, size 26, enabled map[14]: type 1, range 32, base f400, size 19, enabled found-> vendor=0x8086, dev=0x1132, revid=0x11 bus=0, slot=2, func=0 class=03-00-00, hdrtype=0x00, mfdev=0 intpin=a, irq=10 powerspec 2 supports D0 D3 current D0 found-> vendor=0x8086, dev=0x2448, revid=0x03 bus=0, slot=30, func=0 class=06-04-00, hdrtype=0x01, mfdev=0 found-> vendor=0x8086, dev=0x244c, revid=0x03 bus=0, slot=31, func=0 class=06-01-00, hdrtype=0x00, mfdev=1 map[20]: type 4, range 32, base 1800, size 4, enabled found-> vendor=0x8086, dev=0x244a, revid=0x03 bus=0, slot=31, func=1 class=01-01-80, hdrtype=0x00, mfdev=0 map[20]: type 4, range 32, base 1820, size 5, enabled found-> vendor=0x8086, dev=0x2442, revid=0x03 bus=0, slot=31, func=2 class=0c-03-00, hdrtype=0x00, mfdev=0 intpin=d, irq=5 map[20]: type 4, range 32, base 1810, size 4, enabled found-> vendor=0x8086, dev=0x2443, revid=0x03 bus=0, slot=31, func=3 class=0c-05-00, hdrtype=0x00, mfdev=0 intpin=b, irq=5 map[20]: type 4, range 32, base 1880, size 5, enabled found-> vendor=0x8086, dev=0x2444, revid=0x03 bus=0, slot=31, func=4 class=0c-03-00, hdrtype=0x00, mfdev=0 intpin=c, irq=5 map[10]: type 4, range 32, base 1c00, size 8, enabled map[14]: type 4, range 32, base 1840, size 6, enabled found-> vendor=0x8086, dev=0x2445, revid=0x03 bus=0, slot=31, func=5 class=04-01-00, hdrtype=0x00, mfdev=0 intpin=b, irq=5 pci0: on