I also hadan issueto getmISDNworking with HFC cards without problems.
Therefor I switched to zaphfc (use bristuff), this is working perfectly with HFC cards. It does everything I need including MSN support and without problems, even with multiple HFC cards.
So my advice is to get rid of mISDN
From: Giordano Grandis
[EMAIL PROTECTED]Subject: [Asterisk-Users] ztcfg problemHi all,I'm installing two HFC pci card (both in TE mode), I don't have problemwhen load module, but whrn I give ztcfg -vv, I see 6 the six channels
that I configured, then my computer hang and I have to reboot it.
Hi all,
A few days ago I found out with help of some of you guys how to set CLIR. (Calling line identification restriction) My first idea was to use the keypad protocol to set the CLIR with dialing *31* before the number but this was not possible.
So thanks to Damon Estep I got it to work with
From: Damon Estep [EMAIL PROTECTED]
Subject: RE: [Asterisk-Users] How to use * and # as part of number
indialcommand
Good to hear you have found a temporary solution, although I think it is
the permanent solution.
Keypad protocol is a bandaid to fix the real problem, not a
From: Henry Junior [EMAIL PROTECTED]I want to issue a System cmd in my dialpan that is similar to the
unix echo command stated above. *EXCEPT* that I want to pipe theresults into a *new* variable (vs a text file.)Ideally, what would happen is in my diaplan I would issue the 'echo |date' command
From: Arik Funke
arik.funke at gmx.de Hi,my zaphfc is flooding my syslog with two messages (even without asterisk running). Is this normal?:--zaphfc: bchan rx fifo not enough bytes to receive! (z1=1360, z2=1353,
wanted 8 got 7), probably a buffer
Damon Estep wrote:
I did not see an actual error message in your first post, what is the
error message?
Damon,
Well, it is not a 'real' error message, asterisk logs it as a
'warning' , but for me it looks like it is linked to the problem. See
my comments in the logs between [ ].
--
From: Damon Estep [EMAIL PROTECTED]
Subject: RE: [Asterisk-Users] How to use * and # as part of number
indialcommand
To: Asterisk Users Mailing List - Non-Commercial Discussion
asterisk-users@lists.digium.com
Message-ID:
[EMAIL PROTECTED]
Content-Type: text/plain;
extension
(because that can be any extension where I want to put the dial
command after).
Best regards,
Michel Koenen
Damon Estep wrote:
* # are valid in a dialplan
you would start your exten = with the vertical service code *21*
then play prompt, collect digits, play prompt, dial
${exten
channel doesn't support this ?
Are there other channels who do support this?
Or am I doing something wrong and do I have to use another way to get this done?
Thank you in advance for your help.
Best regards,
Michel Koenen
___
--Bandwidth and Colocation
-Asterisk+cmd+AgentCallbackLogin
Have fun with it!
Regards,
Michel Koenen
___
--Bandwidth and Colocation sponsored by Easynews.com --
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
-info.org/tiki-index.php?page=Asterisk+auto-dial+out
So you have to define a context which takes care for the questions
and user feedback and log them, probably AGI will help here too.
Good luck
Michel Koenen
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf
a hint to my problem?
Thank you!
Michel Koenen
___
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE or update options visit:
http://lists.digium.com/mailman/listinfo/asterisk
Yes, it is possible to connect an ISDN to analog A/B adaptor to the HFCPCI.
I'm working though with the zaphfc module and the HFC card in NT mode.
Then I use a (very) old PTT Moduvox 2a (only known in Netherlands I
think) which is connected to the HFC card. The moduvox is a small home
exchange
I have this working with a Teles ISA card, see config below (numbers
are changed because I dont want everybody to call me;-) )
In modem.conf
ZapHFC is configured in zapata.conf, not in modem.conf, right?
--
Tzafrir Cohen | [EMAIL PROTECTED] | VIM is
Yes, I know but I gave the
of the MSN id.
How to get the same results with the ZAPHFC / zapata.conf /
zaptel.conf and/or other config files, or is it not possible due to
the nature of 'zap'?
Thanks in advance for your contributions.
Regards,
Michel Koenen
___
Asterisk-Users mailing
Same here, nothing is coming in anymore on my gmail address neither. I
read your posting by going to the web version of the list. Maybe gmail
is blocking mail from the list or is it really some configuration
setting in the list itself ?
___
looks now like this:
modprobe w6692pci protocol=2 layermask=0xf
Best regards,
Michel Koenen
On 6/6/05, Michel Koenen [EMAIL PROTECTED] wrote:
Hi all,
Does anybody of you have the winbond w6692 working with the
mISDN/chan_misdn.so?
When loading chan_misdn.so from Asterisk, I get a No lower Id
]
[mailto:[EMAIL PROTECTED] On Behalf Of Michel Koenen
Sent: Monday, 6 June 2005 6:28 PM
To: asterisk-users@lists.digium.com
Subject: [Asterisk-Users] mISDN + chan_misdn.so + winbond issue
Hi all,
Does anybody of you have the winbond w6692 working with the
mISDN/chan_misdn.so?
When loading
source
versions of needed packages you have used.
Thank you in advance for your response.
Best regards,
Michel Koenen
___
Asterisk-Users mailing list
Asterisk-Users@lists.digium.com
http://lists.digium.com/mailman/listinfo/asterisk-users
To UNSUBSCRIBE
20 matches
Mail list logo