hi Guys,
Have not heard back on this...
On Thu, Apr 11, 2013 at 9:29 PM, sanity insanity
networksanitytoinsan...@gmail.com wrote:
Hi Guys,
I have a MGCP gateway setup when subscriber fail publisher will work
Call 911 while the call is active shut down the cucm sub services. Make
sure
In regards to Q1, you are accurate in that:
- When the GW fails over to the backup call agent, it will send a RSIP (not
shown in your trace, perhaps not pertinent to your question)
- The call agent will send AUEP messages to the MGCP GW for each endpoint
- The MGCP GW responds to AUEP with a
This is lab 4 question ... but there is now lab 8 work on it
I am really upsad of it
On Tue, Apr 16, 2013 at 9:11 PM, sanity insanity
networksanitytoinsan...@gmail.com wrote:
hi Guys,
Have not heard back on this...
On Thu, Apr 11, 2013 at 9:29 PM, sanity insanity
Hi Guys,
I have a MGCP gateway setup when subscriber fail publisher will work
Call 911 while the call is active shut down the cucm sub services. Make
sure when
Complete to bring up the subscriber services so you can continue with the
tasks on the lab.
Capture the following
-- Backup call agent
Hi Ben,
Yes. You have to add ccm-manager fallback-mgcp for the MGCP in SRST
scenario.
*Configuring MGCP Gateway Fallback and Cisco SRST ** ***
* To make outbound calls while in SRST mode on your MGCP gateway, you must
configure two fallback commands on the MGCP gateway. These two commands
allow
Hi All my Friends,
If the question is asked for configuring busy out few channels from MGCP
gateway is it just enough if we used. But if it not mentioned how many
channels we need to busy out what woul be correct. Just open a all
channels or keep busy few ??
*pri-group timeslots [1]-[X] service
Guys
I configured MGCP on a E1 controller using cc-manager config server it
generated the output below. Is there anything wrong with the config ? I want to
know if it is safe to do it during the real lab. It works in my own lab. Please
advise.
ccm-manager redundant-host 192.168.1.41
The second option will work with both route patterns. I tested it several times
and it always worked for me.
Regards,
Mohamed Gazzaz
Date: Sat, 22 Dec 2012 11:52:28 -0600
From: ramcharan.a...@gmail.com
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] MGCP gateway : DDI
trailing # for h323 also
Regards
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Ramcharan Arya
Sent: Σάββατο, 22 Δεκεμβρίου 2012 8:14 μμ
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] MGCP gateway : DDI for International Route
:
ccie_voice-boun...@onlinestudylist.com] *On Behalf Of *Ramcharan Arya
*Sent:* Σάββατο, 22 Δεκεμβρίου 2012 8:14 μμ
*To:* ccie_voice@onlinestudylist.com
*Subject:* [OSL | CCIE_Voice] MGCP gateway : DDI for International Route
Pattern options
** **
Hello,
I have a requirement to use SLRG
Sure enough - it is a CSS named all containing a ton of partitions. Thanks
Randall - should have figured this out. This doesn't seem to be a very
efficient way of doing things. Can someone explain the behavior when you
assign a CSS to a Gateway with multiple partitions spanning multiple
Greetings all - I'm researching a cluster located in Dublin and it has an MGCP
Gateway support the Paris Site. I'm reviewing the gateway under the E1 PRI and
the CSS is set to ALL. Anyone know what this means?? Does it search through
all the CSS's in the list for a match?? Never seen this
It is a CSS named all. Look at the CSS and you can see the partitions that are
reachable
Randall
Sent from my iPhone
On Dec 12, 2011, at 6:04 PM, michael.se...@compucom.com wrote:
Greetings all – I’m researching a cluster located in Dublin and it has an
MGCP Gateway support the Paris
Check your isdn switch type.
Sent from my iPhone 4.
On Jul 18, 2011, at 9:46 PM, ccie_voice-requ...@onlinestudylist.com wrote:
MGCP Gateway reg issue (not l2 TEI or l3bind) (steven moran)
___
For more information regarding industry leading CCIE
Verify also lincode, framing, and clocking. I am not sure what the default is
on 26XX.
Sent from my iPhone 4.
___
For more information regarding industry leading CCIE Lab training, please visit
www.ipexpert.com
Are you a CCNP or CCIE and looking
Dear all,
I am not sure what is going on here, I welcome all suggestions
I have rebuilt a new Pub and Sub environment (10.10.210.12 and 13)
I have reloaded the router without the controller config and triple checked
the config and built all of the ISDN connectivity again.
Here is what is
Hello Steven,
You do not show that you are using the following commands
ccm-manager config server
ccm-manager config
So I do not believe that the ISDN configuration on the CUCM will be applied,
only your configuration on the router, which is why you also have to type no
mgcp/mgcp to have
Bill,
thanks for the response, the idea from the IPExperts is to use the
ccm-manager mgcp command and specify a fractional E1 - all of the commands
for the gateway are done on the router (control/media bind commands) and the
define call-agent etc. I too have no issues using the 2811 router - all
CUCM does not support fractional PRIs in MGCP officially.
- Reply message -
From: steven moran smoran...@gmail.com
Date: Sun, Jul 17, 2011 8:45 pm
Subject: [OSL | CCIE_Voice] MGCP Gateway reg issue (not l2 TEI or l3 bind)
To: ccie_voice@onlinestudylist.com
Dear all,
thanks for all
Yes, a sh isdn status showed multiple frame established. More often than not
I have to actually apply:
Serial 0/0/0:23
isdn bind-l3 ccm-manager
Then
no isdn bind-l3 ccm-manager
isdn bind-l3 ccm-manager
in order to get multiple frame established. In playing around with it today
I figured
Hi - this is a bug with mgcp when using l0
http://www.onlinestudylist.com/archives/ccie_voice/2011-May/074217.html
hth
On Mon, Jul 11, 2011 at 9:36 AM, CCIEVoiceKP ccievoic...@gmail.com wrote:
Yes, a sh isdn status showed multiple frame established. More often than
not I have to actually
I seem to be running into an intermittent problem with my MGCP gateways. I
configure the router, its registered to CUCM, significant digits set
correctly ... all is good except I can not receive inbound calls from the
PSTN ... sometimes! A reload of the router fixes the issue when it
happens. I
: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP gateway - 1 ring disconnect (7965),
fastbusy (7960)
Hi
Did you do a show isdn status?
You may have to do a no isdn bind-l3 ccm manager on the serial interface
Also no mgcp
no mgcp bind control
mgcp bind control source interface
@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP gateway - 1 ring disconnect (7965),
fastbusy (7960)
Check your source interface (bind), CUCM must be registered with the same bind
interface mentioned in the mgcp configuration.
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun
hi all,
i configured mgcp gateway on HQ RTR.
when i call from PSTN to a 7965 phone, i get fastbusy after 1 ring.
when i call from PSTN to a 7960 phone (which is set to auto answer after 2
rings), i get fastbusy straight away.
so, i issued 'no mgcp' - waited for 60 sec to ensure it deregister
Hi
Did you do a show isdn status?
You may have to do a no isdn bind-l3 ccm manager on the serial interface
Also no mgcp
no mgcp bind control
mgcp bind control source interface lo0
Mgcp
Huh
Rc
Sent from my iPhone
On Apr 28, 2011, at 8:19 PM, Adil Shaikh adil.sha...@gmail.com wrote:
hi all,
CCIE #26199 (Voice)
Consultant
Cygate AB
Eric Perssons väg 21, SE-217 62 MALMÖ
Från: Naoufal Kerboute [naou...@mhdinfotech.com]
Skickat: den 4 april 2011 05:56
Till: ccie_voice@onlinestudylist.com
Ämne: [OSL | CCIE_Voice] MGCP Gateway registration Issue
Hi gents
Hi gents,
Please I need your help for the below.
I'm always facing problem to get the MGCP gateway up, always the first time
register with the serial interface instead of the bind interface (loopback or
voice vlan int) that I specified in the config. I've tried to remove the isdn
bind-l3
Try leaving the controller in a shutdown state until everything is configured.
Then do a no shut on it. This seems to work for me every time.
--
On Apr 3, 2011, at 21:56, Naoufal Kerboute naou...@mhdinfotech.com wrote:
Hi gents,
Please I need your help for the below.
I’m always
Hello guys,
I am just curious. Can somebody tell me what could be d reason why outbound
call through an mgcp gateway will fail. Gateway registers fine with full T1
channels, pt/css are very okay.
Suggestions are needed please.
Tks.
Sent from my Nokia phone
Från: Scott Totaro (stotaro) [stot...@cisco.com]
Skickat: den 8 februari 2010 01:15
Till: Jeff Price (jeffpric); afatsum
Kopia: ccie_voice@onlinestudylist.com
Ämne: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Because the D-channel is backhauled to CUCM for MGCP
roger.kallb...@cygate.se
Från: Scott Totaro (stotaro) [stot...@cisco.com]
Skickat: den 8 februari 2010 01:15
Till: Jeff Price (jeffpric); afatsum
Kopia: ccie_voice@onlinestudylist.com
Ämne: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Because the D
, February 08, 2010 2:09 PM
To: Jeff Price (jeffpric)
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
I'm sorry Jeff. I -always- do that but if I go to the CUCM interface I do it
right.
The Route List can be reset -- try that and see if you can suddenly start
dialing. If not, try
: [OSL | CCIE_Voice] MGCP Gateway Problem
I'm sorry Jeff. I -always- do that but if I go to the CUCM interface I do
it right.
The Route List can be reset -- try that and see if you can suddenly start
dialing. If not, try resetting the gateway too.We've had cases in our
production
, 2010 3:11 PM
To: Jeff Price (jeffpric)
Cc: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Jeff - you ARE able to make the calls?
Sounds like you may have had some kind of replication issue going on between
the pub/sub.
-jeff
On Mon, Feb 8, 2010 at 5:47 PM
To: Jeff Price (jeffpric)
Cc: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Jeff,
If debug q931 isn't producing output and everything appears to be
registered right I'd assume that you have an issue with your phone/line
CSS, route patterns, route list
*To:* ccie_voice@onlinestudylist.com
*Subject:* Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Good morning everyone,
Thanks Jeff for the response. I’m going to be looking into all of this.
However, my configuration is as follow:
HQ Phones – CSS_HQ_DEVICES (DEVICE, no LINE CSS as of yet
, February 07, 2010 10:59 AM
*To:* ccie_voice@onlinestudylist.com
*Subject:* Re: [OSL | CCIE_Voice] MGCP Gateway Problem
Good morning everyone,
Thanks Jeff for the response. I'm going to be looking into all of
this.
However, my configuration is as follow:
HQ Phones - CSS_HQ_DEVICES (DEVICE
: Jeff Price (jeffpric)
Sent: Sunday, February 07, 2010 12:35 PM
To: 'afatsum'
Cc: ccie_voice@onlinestudylist.com
Subject: RE: [OSL | CCIE_Voice] MGCP Gateway Problem
I have deactivated all of the services on the SUB and let everything
register with the PUB.
Jeff
-Original Message-
From
(Jason Granat)
--
Message: 1
Date: Sun, 7 Feb 2010 14:40:51 -0600
From: Jeff Price (jeffpric) jeffp...@cisco.com
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
To: afatsum afat...@verizon.net
Cc: ccie_voice
on the router terminating the D-channel (e.g. show
isdn history.)
Hope this helps,
Scott
-Original Message-
From: Jeff Price (jeffpric)
Sent: Sunday, February 07, 2010 3:41 PM
To: afatsum
Cc: ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
It appears
: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
It appears that my transformation is working. When dialing
91408425, the display on the phone says To 408425. And the
DNA analysis shows what the CUCM is going through process-wise. Yet I
am still not receiving any ISDN Q931 debug output
is never making it to the gateway.
Scott
-Original Message-
From: afatsum [mailto:afat...@verizon.net]
Sent: Sunday, February 07, 2010 7:46 PM
To: Scott Totaro (stotaro)
Cc: Jeff Price (jeffpric); ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] MGCP Gateway Problem
If you
Subject: RE: [OSL | CCIE_Voice] MGCP Gateway Problem
I stand corrected...sorry for the misdirection. I guess it's the show
commands that haven't worked whereas the debugs are still useful. I'd
still suggest investigating the detailed trace files for the source of
the failure as Mustafa points out
Hey everyone,
I wanted see if anyone had any ideas as to what may be wrong here. I
have set up the MGCP gateway correctly as far as I can tell. It is
registered with CUCM. Attached is the GW's config as well as show
ccm-manager, show isdn status and the call routing elements.
Everything
Jeff,
If debug q931 isn't producing output and everything appears to be registered
right I'd assume that you have an issue with your phone/line CSS, route
patterns, route list, route group, etc.
Have you tried resetting the Route Group? Have you tried the dialed number
analyzer to see where
13, 2008 2:57 PM
*To:* ccie_voice@onlinestudylist.com
*Subject:* [OSL | CCIE_Voice] MGCP gateway not registered ?
hi,
I am using Grade Lab voice lab,
any body ever experienced this issue before and know the workaround ?
- 2811 MGCP gateway is registered in Call Manager (dial-peer
hi tks James , yes it work, just remove and re-add bind command
--- On Mon, 11/17/08, Ryan Trauernicht [EMAIL PROTECTED] wrote:
From: Ryan Trauernicht [EMAIL PROTECTED]
Subject: Re: [OSL | CCIE_Voice] MGCP gateway not registered ?
To: James Key [EMAIL PROTECTED]
Cc: [EMAIL PROTECTED], ccie_voice
hi,
I am using Grade Lab voice lab,
any body ever experienced this issue before and know the workaround ?
- 2811 MGCP gateway is registered in Call Manager (dial-peer , mgcp config is
in place)
- however the sh ccm-manager is showwing down
I have :
1. restart CCM service and reboot CCM
2.
Are you using the MGCP bind commands? If so, try removing these and
re-add.
James
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Erwan Erwan
Sent: Thursday, November 13, 2008 2:57 PM
To: ccie_voice@onlinestudylist.com
Subject: [OSL | CCIE_Voice] MGCP gateway
I had read somewhere you don't need service MGCPAPP under dial-peer
for getting the MGCP to work , I think it was on cisco forum . and the
reason was when MGCP fallback happens . you can do a search on that one , I
tested this in LAB and without Service MGCPAPP everything worked fine even
when on
: Re: [OSL | CCIE_Voice] MGCP Gateway POTS dial-peer
I had read somewhere you don't need service MGCPAPP under dial-peer for
getting the MGCP to work , I think it was on cisco forum . and the
reason was when MGCP fallback happens .
you can do a search on that one , I tested this in LAB
Hi,
For Cisco IOS Software Release 12.3(7)T or later the Pots dial-peer
configuration for MGCP gateway should like below or even service mgcpapp is
not needed ? Could you please correct me if I am wrong ?
dial-peer voice 10 pots
service mgcpapp
incoming called-number .
direct-inward-dial
Hi,
I have in my notes that it is not recommended to use the MGCP ccm-manager
config and ccm-manager config server commands. I always use these commands
in my lab and I can't recall the reason the instructor said that it was a
bad idea to use these commands. Does somebody remember why the
Right and the next time you reset the gateway, it will change it back.
However, you can busy out the remaining channels with B-channel maintenance
status... So, you can accomplish the same thing and still have MGCP push a
config.
Jonathan
On Mon, Sep 8, 2008 at 3:50 PM, Robertico Gonzalez
Hi all,
I am having problem getting my mgcp gateway to register to CallManager. I
tried reset the gateway from CallManager, and issue no mgcp/mgcp in the
router. And, end up rebooting the CallManager and the router. But still no
luck :-(
Please kindly advice.
Here are some outputs:
Can you run a 'u all' then a 'debug mgcp' and try the 'no mgcp' /
'mgcp' again?
and send all the output?
thanks
--
Mark Snow
CCIE #14073 (Voice, Security)
CCSI #31583
Senior Technical Instructor - IPexpert, Inc.
Telephone: +1.810.326.1444
Fax: +1.309.413.4097
Mailto: [EMAIL PROTECTED]
--
57 matches
Mail list logo
