Re: [OSL | CCIE_Voice] QoS for HWIC module
Does it trust CoS or DSCP? Well, basically, I guess what does it trust, it trust just like the Router is trusting anything and relaying any QoS markings, am I right? But as for SRR, HWIC module interfaces does not undertand the command srr-queue or anything that begins with srr key word. On Tue, Dec 6, 2011 at 12:25 AM, Mohd Baqari baqari.voic...@gmail.comwrote: In HWIC trust is the default state. Also. srr can be configured. Regards, Mohammed Al Baqari Sent from my iPhone On Dec 5, 2011, at 5:12 PM, datucha123 datucha123 datucha...@gmail.com wrote: Hello, We can configur the L2 QoS on 3750 switch using SRR, Port based Trusts and etc. But what about the 4 port HWIC module? What kind of QoS must be done for that? I have tryed but the HWIC ports does not undertand the mls qos command. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
You are missing H323-ID in gatekeeper static binding configuration. You need
to configure H323-ID of your gateway under gatekeeper in static binding.
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002 h323id BR2-CME
Regards,
Mohammed Al Baqari
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Yankee Lo
Sent: Tuesday, December 06, 2011 1:08 AM
To: Guoming Zhang; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
Did you enter gateway after you configured h323-gateway?
Try remove h323-gateway voip bind srcaddr 200.200.110.2 from lo0, configure
this on the voice interface.
From: Guoming Zhang guozhang20...@yahoo.com
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent: Monday, December 5, 2011 12:01 AM
Subject: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
Need to help to figure it out why my gateway would not register to GK.
--GK configure--
HQ#show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com http://ccie.cisco.com/ 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras
200.200.210.239 55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002
no shutdown
...
--- Gateway configure --
BR2-CME#show run in loopback 0
Building configuration...
Current configuration : 234 bytes
!
interface Loopback0
ip address 200.200.110.2 255.255.255.255
h323-gateway voip interface
h323-gateway voip id Z_ZONE ipaddr 200.200.110.3 1719
h323-gateway voip h323-id BR2-CME
h323-gateway voip bind srcaddr 200.200.110.2
end
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol cisco
h323
no call service stop
call preserve
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
registrar server expires max 3600 min 300
!
!
=== debug message from gateway ==
BR2-CME#show debug
H.225:
H.225 ASN1 Messages debugging is on
BR2-CME#
Dec 5 07:45:42.122: RAS OUTGOING PDU ::=
value RasMessage ::= gatekeeperRequest :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
rasAddress ipAddress :
{
ip 'C8C86E02'H
port 60717
}
endpointType
{
vendor
{
vendor
{
t35CountryCode 181
t35Extension 0
manufacturerCode 18
}
productId '436973636F47617465776179'H
versionId '32'H
}
gateway
{
protocol
{
voice :
{
supportedPrefixes
{
}
},h323 :
{
supportedPrefixes
{
}
}
}
}
mc FALSE
undefinedNode FALSE
}
gatekeeperIdentifier {Z_ZONE}
endpointAlias
{
BR2-CME# dialedDigits : 3000,
dialedDigits : 3004,
dialedDigits : 6688,
dialedDigits : 8000,
dialedDigits : ,
dialedDigits : 1112,
dialedDigits : 7001,
dialedDigits : ,
dialedDigits : 4445,
dialedDigits : 3020,
dialedDigits : 711,
h323-ID : {BR2-CME}
}
}
Dec 5 07:45:42.126: RAS OUTGOING ENCODE BUFFER::=
00A00033060008914A000400C8C86E02ED2D28C0B5120B436973636F4761746577617900
3240023C0501002C0501000280005A005F005A004F004E00450C0180633301806337018099BB
0180B3330180018044450180A334018001807778018063530100A444060042005200
32002D0043004D0045
Dec 5 07:45:42.126:
Dec 5 07:45:42.138: RAS INCOMING ENCODE BUFFER::=
04800033060008914A00040A005A005F005A004F004E004500C8C86E0306B7
Dec 5 07:45:42.138:
Dec 5 07:45:42.138: RAS INCOMING PDU ::=
value RasMessage ::= gatekeeperConfirm :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
gatekeeperIdentifier {Z_ZONE}
rasAddress ipAddress :
{
ip 'C8C86E03'H
port 1719
}
}
Dec 5 07:45:42.138: H225 NONSTD OUTGOING PDU ::=
value RasnonStdUsageTypes ::=
{
callModes NULL
}
Dec 5 07:45:42.138: H225 NONSTD OUTGOING ENCODE BUFFER::= 40
Dec 5 07:45:42.138:
Dec 5 07:45:42.138: RAS OUTGOING PDU ::=
value RasMessage ::= registrationRequest :
{
requestSeqNum 53
protocolIdentifier { 0 0 8 2250 0 4 }
discoveryComplete TRUE
callSignalAddress
{
ipAddress :
{
ip 'C8C86E02'H
port 1720
}
}
rasAddress
{
ipAddress :
{
ip 'C8C86E02'H
port 60717
}
}
terminalType
{
vendor
Re: [OSL | CCIE_Voice] Strange behavior on MGCP gateways
try restarting the ccm services.. or did you try and figure what the issue was??? On Fri, Dec 2, 2011 at 8:02 AM, ccielabrat ccielab...@gmail.com wrote: I noticed a weird thing while testing MGCP. If I call out to my pstn phone and answer the call by pressing the answer soft key , the call will disconnect after about two minutes. If I answer the call with the speaker button , it stays up forever. I'm guessing the problem is I don't have handsets on any of my phones , so when I answer with the answer softkey , the phone is off hook and sending dead air packets. Somehow , mgcp see this as an error condition after two minutes or so and kills the call. If the call is on speaker, I guess it picks up enough noise to keep the call from being considered inactive. Weird. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gateway failed to register to GK
no, still the same after I configure h323 id.
HQ# show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239
55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
1719 e164 3006 e164 3002 h323id BR2-CME
no shutdown
BR2-CME#show gateway
H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1
H.323 service is up
Gateway BR2-CME is not registered to any gatekeeper
thanks,
guoming
From: Mohammed Al Baqari baqari.voic...@gmail.com
To: 'Yankee Lo' yanke...@yahoo.com; 'Guoming Zhang'
guozhang20...@yahoo.com; ccie_voice@onlinestudylist.com
Sent: Tuesday, December 6, 2011 5:11 PM
Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
You are missing H323-ID in gatekeeper static binding configuration. You need to
configure H323-ID of your gateway under gatekeeper in static binding.
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002 h323id BR2-CME
Regards,
Mohammed Al Baqari
From:ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Yankee Lo
Sent: Tuesday, December 06, 2011 1:08 AM
To: Guoming Zhang; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
Did you enter gateway after you configured h323-gateway?
Try remove h323-gateway voip bind srcaddr 200.200.110.2 from lo0, configure
this on the voice interface.
From:Guoming Zhang guozhang20...@yahoo.com
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent: Monday, December 5, 2011 12:01 AM
Subject: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
Need to help to figure it out why my gateway would not register to GK.
--GK configure--
HQ#show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239
55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002
no shutdown
...
--- Gateway configure --
BR2-CME#show run in loopback 0
Building configuration...
Current configuration : 234 bytes
!
interface Loopback0
ip address 200.200.110.2 255.255.255.255
h323-gateway voip interface
h323-gateway voip id Z_ZONE ipaddr 200.200.110.3 1719
h323-gateway voip h323-id BR2-CME
h323-gateway voip bind srcaddr 200.200.110.2
end
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol cisco
h323
no call service stop
call preserve
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
registrar server expires max 3600 min 300
!
!
=== debug message from gateway ==
BR2-CME#show debug
H.225:
H.225 ASN1 Messages debugging is on
BR2-CME#
Dec 5 07:45:42.122: RAS OUTGOING PDU ::=
value RasMessage ::= gatekeeperRequest :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
rasAddress ipAddress :
{
ip 'C8C86E02'H
port 60717
}
endpointType
{
vendor
{
vendor
{
t35CountryCode 181
t35Extension 0
manufacturerCode 18
}
productId '436973636F47617465776179'H
versionId '32'H
}
gateway
{
protocol
{
voice :
{
supportedPrefixes
{
}
}, h323 :
{
supportedPrefixes
{
}
}
}
}
mc FALSE
undefinedNode FALSE
}
gatekeeperIdentifier {Z_ZONE}
endpointAlias
{
BR2-CME# dialedDigits : 3000,
dialedDigits : 3004,
dialedDigits : 6688,
dialedDigits : 8000,
dialedDigits : ,
dialedDigits : 1112,
dialedDigits : 7001,
dialedDigits : ,
dialedDigits : 4445,
dialedDigits : 3020,
dialedDigits : 711,
h323-ID : {BR2-CME}
}
}
Dec 5 07:45:42.126: RAS OUTGOING ENCODE BUFFER::=
00A00033060008914A000400C8C86E02ED2D28C0B5120B436973636F47617465776179003240023C0501002C0501000280005A005F005A004F004E00450C0180633301806337018099BB0180B3330180018044450180A334018001807778018063530100A44406004200520032002D0043004D0045
Dec 5 07:45:42.126:
Dec 5 07:45:42.138: RAS INCOMING ENCODE BUFFER::=
04800033060008914A00040A005A005F005A004F004E004500C8C86E0306B7
Dec 5 07:45:42.138:
Dec 5 07:45:42.138: RAS INCOMING PDU ::=
value RasMessage ::= gatekeeperConfirm :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
Re: [OSL | CCIE_Voice] CUCM Log Problem
Yes, but the when I look for FIle View recent file, it is still the same file that I am currectly tailing. On Tue, Dec 6, 2011 at 1:25 PM, Douglas Crabbe dougcra...@gmail.com wrote: is the issue that the tail command is opening a single file - as soon as the system changes to a new file in its rotation, the tail stops as the file isn't being updated anymore? i.e when you type file tail activelog /cm/trace/ccm/sdi recent the recent file is ccm001.txt but this soon changes ( when the file gets to 2MB ) and the system is writing new entries to ccm002.txt. On 6 December 2011 08:24, datucha123 datucha123 datucha...@gmail.comwrote: I am in the correct, Call Processing Agent - Subscriber, but still not Logs. Actually, when I start logging, some logs appear, but then the stops, and no more logs are logged in the screen any more. On Tue, Dec 6, 2011 at 12:08 AM, Edgar Feliz ejzi...@gmail.com wrote: Are you looking at the Sub CUCM or whatever you primary call processing agent is. IF you are in the wrong CUCM you will not see any call information. E On Mon, Dec 5, 2011 at 10:56 AM, datucha123 datucha123 datucha...@gmail.com wrote: Hello, I have a problem with CUCM - when trying to view Logs in real time either through RTMT or file tail command in CLI, the logs starts only for several lines, and then stops logging, there are no new information (Loggin messages) coming up any more. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gateway failed to register to GK
It should work.
One thing I noticed is to remove e164 addresses from GK static binding. The
reason is that your RRQ request is sending multiple DNs but you are
configuring two only on GK. There is a mismatch between the configured DNs
on GK and the actual DNs sent from gateway.
Try not to configure DNs in static binding. It will register and all DNs
will be taken automatically from your RRQ.
From: Guoming Zhang [mailto:guozhang20...@yahoo.com]
Sent: Tuesday, December 06, 2011 1:34 PM
To: Mohammed Al Baqari; 'Yankee Lo'; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
no, still the same after I configure h323 id.
HQ# show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras
200.200.210.239 55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
1719 e164 3006 e164 3002 h323id BR2-CME
no shutdown
BR2-CME#show gateway
H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1
H.323 service is up
Gateway BR2-CME is not registered to any gatekeeper
thanks,
guoming
_
From: Mohammed Al Baqari baqari.voic...@gmail.com
To: 'Yankee Lo' yanke...@yahoo.com; 'Guoming Zhang'
guozhang20...@yahoo.com; ccie_voice@onlinestudylist.com
Sent: Tuesday, December 6, 2011 5:11 PM
Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
You are missing H323-ID in gatekeeper static binding configuration. You need
to configure H323-ID of your gateway under gatekeeper in static binding.
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002 h323id BR2-CME
Regards,
Mohammed Al Baqari
From: ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Yankee Lo
Sent: Tuesday, December 06, 2011 1:08 AM
To: Guoming Zhang; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
Did you enter gateway after you configured h323-gateway?
Try remove h323-gateway voip bind srcaddr 200.200.110.2 from lo0, configure
this on the voice interface.
From: Guoming Zhang guozhang20...@yahoo.com
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent: Monday, December 5, 2011 12:01 AM
Subject: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
Need to help to figure it out why my gateway would not register to GK.
--GK configure--
HQ#show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com http://ccie.cisco.com/ 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras
200.200.210.239 55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002
no shutdown
...
--- Gateway configure --
BR2-CME#show run in loopback 0
Building configuration...
Current configuration : 234 bytes
!
interface Loopback0
ip address 200.200.110.2 255.255.255.255
h323-gateway voip interface
h323-gateway voip id Z_ZONE ipaddr 200.200.110.3 1719
h323-gateway voip h323-id BR2-CME
h323-gateway voip bind srcaddr 200.200.110.2
end
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol cisco
h323
no call service stop
call preserve
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
registrar server expires max 3600 min 300
!
!
=== debug message from gateway ==
BR2-CME#show debug
H.225:
H.225 ASN1 Messages debugging is on
BR2-CME#
Dec 5 07:45:42.122: RAS OUTGOING PDU ::=
value RasMessage ::= gatekeeperRequest :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
rasAddress ipAddress :
{
ip 'C8C86E02'H
port 60717
}
endpointType
{
vendor
{
vendor
{
t35CountryCode 181
t35Extension 0
manufacturerCode 18
}
productId '436973636F47617465776179'H
versionId '32'H
}
gateway
{
protocol
{
voice :
{
supportedPrefixes
{
}
},h323 :
{
supportedPrefixes
{
}
}
}
}
mc FALSE
undefinedNode FALSE
}
gatekeeperIdentifier {Z_ZONE}
endpointAlias
{
BR2-CME# dialedDigits : 3000,
dialedDigits : 3004,
dialedDigits : 6688,
dialedDigits : 8000,
dialedDigits : ,
dialedDigits : 1112,
dialedDigits : 7001,
dialedDigits : ,
dialedDigits : 4445,
dialedDigits : 3020,
[OSL | CCIE_Voice] Automated Reply Re: CCIE_Voice Digest, Vol 70, Issue 43
This is an automated reply to your message CCIE_Voice Digest, Vol 70, Issue 43 sent to stewart.mcfarl...@provista-uk.com. Dear ccie_voice-requ...@onlinestudylist.com Thank you for your email. Please note that due to unforseen circumstances I will be out of the office for the rest of this week (w/c 17/10/11). If you require any assistance please contact the provista office on 08456424642. For technical assistance please contact serviced...@provista-uk.com. Thanks Stewart ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Problem with Attendant Console
Hi Guys I`m busy with Volume 2 Lab 1 and I have an issue with the AC setup ,my Always route member has been configured and added last in the hunt list ,but when I phone the ac pilot it sends me to the Voicemail for the member that was chosen in the hunt list. I have created a CTI RP with number *5002 and I have a mask of configured on my VM profile ,and this number is my Always route member. I have also tried to set the queue hold time at 5 seconds ,but it still rings for about 12 seconds and then gets forwarded to the VM for the number that the call was ringing at. Any ideas ? Rynard ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] gateway failed to register to GK
Hi Mohammed,
as far as I remove the static binding from HQ for CME-BR2, CME-BR2 registers to
GK.
But that is not my intention. Since 3002 and 3006 are CME DN and they are not
configured to register to GK, and I only want to register both DN statically to
GKand I do not want to use tech-prefix and zone to do gk routing. Should I
include all DNs on CME-BR2 to the alias static command?
thanks,
guoming
From: Mohammed Al Baqari baqari.voic...@gmail.com
To: 'Guoming Zhang' guozhang20...@yahoo.com; 'Yankee Lo'
yanke...@yahoo.com; ccie_voice@onlinestudylist.com
Sent: Tuesday, December 6, 2011 5:59 PM
Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK
It should work.
One thing I noticed is to remove e164 addresses from GK static binding. The
reason is that your RRQ request is sending multiple DNs but you are configuring
two only on GK. There is a mismatch between the configured DNs on GK and the
actual DNs sent from gateway.
Try not to configure DNs in static binding. It will register and all DNs will
be taken automatically from your RRQ.
From:Guoming Zhang [mailto:guozhang20...@yahoo.com]
Sent: Tuesday, December 06, 2011 1:34 PM
To: Mohammed Al Baqari; 'Yankee Lo'; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
no, still the same after I configure h323 id.
HQ# show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239
55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
1719 e164 3006 e164 3002 h323id BR2-CME
no shutdown
BR2-CME#show gateway
H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1
H.323 service is up
Gateway BR2-CME is not registered to any gatekeeper
thanks,
guoming
From:Mohammed Al Baqari baqari.voic...@gmail.com
To: 'Yankee Lo' yanke...@yahoo.com; 'Guoming Zhang'
guozhang20...@yahoo.com; ccie_voice@onlinestudylist.com
Sent: Tuesday, December 6, 2011 5:11 PM
Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
You are missing H323-ID in gatekeeper static binding configuration. You need to
configure H323-ID of your gateway under gatekeeper in static binding.
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002 h323id BR2-CME
Regards,
Mohammed Al Baqari
From:ccie_voice-boun...@onlinestudylist.com
[mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Yankee Lo
Sent: Tuesday, December 06, 2011 1:08 AM
To: Guoming Zhang; ccie_voice@onlinestudylist.com
Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK
Did you enter gateway after you configured h323-gateway?
Try remove h323-gateway voip bind srcaddr 200.200.110.2 from lo0, configure
this on the voice interface.
From:Guoming Zhang guozhang20...@yahoo.com
To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com
Sent: Monday, December 5, 2011 12:01 AM
Subject: [OSL | CCIE_Voice] gateway failed to register to GK
Hi,
Need to help to figure it out why my gateway would not register to GK.
--GK configure--
HQ#show run | b gatek
gatekeeper
zone local Z_ZONE ccie.cisco.com 200.200.110.3
alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239
55616 e164 5001 e164 5002 e164 1001 e164 1002
alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2
62766 e164 3006 e164 3002
no shutdown
...
--- Gateway configure --
BR2-CME#show run in loopback 0
Building configuration...
Current configuration : 234 bytes
!
interface Loopback0
ip address 200.200.110.2 255.255.255.255
h323-gateway voip interface
h323-gateway voip id Z_ZONE ipaddr 200.200.110.3 1719
h323-gateway voip h323-id BR2-CME
h323-gateway voip bind srcaddr 200.200.110.2
end
voice service voip
allow-connections h323 to h323
allow-connections h323 to sip
allow-connections sip to h323
allow-connections sip to sip
fax protocol cisco
h323
no call service stop
call preserve
sip
bind control source-interface Loopback0
bind media source-interface Loopback0
registrar server expires max 3600 min 300
!
!
=== debug message from gateway ==
BR2-CME#show debug
H.225:
H.225 ASN1 Messages debugging is on
BR2-CME#
Dec 5 07:45:42.122: RAS OUTGOING PDU ::=
value RasMessage ::= gatekeeperRequest :
{
requestSeqNum 52
protocolIdentifier { 0 0 8 2250 0 4 }
rasAddress ipAddress :
{
ip 'C8C86E02'H
port 60717
}
endpointType
{
vendor
{
vendor
{
t35CountryCode 181
t35Extension 0
manufacturerCode 18
}
productId '436973636F47617465776179'H
versionId '32'H
}
gateway
{
protocol
{
Re: [OSL | CCIE_Voice] gateway failed to register to GK
What I said to remove only e164 numbers not full static binding. Your numbers received in RRQ aren't matching the numbers configured in your static binding. This miss match create issue. Do one thing .. Disable e164 registration to gatekeeper on gateway . then use static binding on GK. This won't send DNs in RRQ and then you can add any DNs in manual mapping. From: Guoming Zhang [mailto:guozhang20...@yahoo.com] Sent: Tuesday, December 06, 2011 3:35 PM To: Mohammed Al Baqari; 'Yankee Lo'; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK Hi Mohammed, as far as I remove the static binding from HQ for CME-BR2, CME-BR2 registers to GK. But that is not my intention. Since 3002 and 3006 are CME DN and they are not configured to register to GK, and I only want to register both DN statically to GK and I do not want to use tech-prefix and zone to do gk routing. Should I include all DNs on CME-BR2 to the alias static command? thanks, guoming _ From: Mohammed Al Baqari baqari.voic...@gmail.com To: 'Guoming Zhang' guozhang20...@yahoo.com; 'Yankee Lo' yanke...@yahoo.com; ccie_voice@onlinestudylist.com Sent: Tuesday, December 6, 2011 5:59 PM Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK It should work. One thing I noticed is to remove e164 addresses from GK static binding. The reason is that your RRQ request is sending multiple DNs but you are configuring two only on GK. There is a mismatch between the configured DNs on GK and the actual DNs sent from gateway. Try not to configure DNs in static binding. It will register and all DNs will be taken automatically from your RRQ. From: Guoming Zhang [mailto:guozhang20...@yahoo.com] Sent: Tuesday, December 06, 2011 1:34 PM To: Mohammed Al Baqari; 'Yankee Lo'; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK no, still the same after I configure h323 id. HQ# show run | b gatek gatekeeper zone local Z_ZONE ccie.cisco.com 200.200.110.3 alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239 55616 e164 5001 e164 5002 e164 1001 e164 1002 alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2 1719 e164 3006 e164 3002 h323id BR2-CME no shutdown BR2-CME#show gateway H.323 ITU-T Version: 4.0 H323 Stack Version: 0.1 H.323 service is up Gateway BR2-CME is not registered to any gatekeeper thanks, guoming _ From: Mohammed Al Baqari baqari.voic...@gmail.com To: 'Yankee Lo' yanke...@yahoo.com; 'Guoming Zhang' guozhang20...@yahoo.com; ccie_voice@onlinestudylist.com Sent: Tuesday, December 6, 2011 5:11 PM Subject: RE: [OSL | CCIE_Voice] gateway failed to register to GK Hi, You are missing H323-ID in gatekeeper static binding configuration. You need to configure H323-ID of your gateway under gatekeeper in static binding. alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2 62766 e164 3006 e164 3002 h323id BR2-CME Regards, Mohammed Al Baqari From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of Yankee Lo Sent: Tuesday, December 06, 2011 1:08 AM To: Guoming Zhang; ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] gateway failed to register to GK Did you enter gateway after you configured h323-gateway? Try remove h323-gateway voip bind srcaddr 200.200.110.2 from lo0, configure this on the voice interface. From: Guoming Zhang guozhang20...@yahoo.com To: ccie_voice@onlinestudylist.com ccie_voice@onlinestudylist.com Sent: Monday, December 5, 2011 12:01 AM Subject: [OSL | CCIE_Voice] gateway failed to register to GK Hi, Need to help to figure it out why my gateway would not register to GK. --GK configure-- HQ#show run | b gatek gatekeeper zone local Z_ZONE ccie.cisco.com http://ccie.cisco.com/ 200.200.110.3 alias static 200.200.210.239 1720 gkid Z_ZONE gateway voip ras 200.200.210.239 55616 e164 5001 e164 5002 e164 1001 e164 1002 alias static 200.200.110.2 1720 gkid Z_ZONE gateway voip ras 200.200.110.2 62766 e164 3006 e164 3002 no shutdown ... --- Gateway configure -- BR2-CME#show run in loopback 0 Building configuration... Current configuration : 234 bytes ! interface Loopback0 ip address 200.200.110.2 255.255.255.255 h323-gateway voip interface h323-gateway voip id Z_ZONE ipaddr 200.200.110.3 1719 h323-gateway voip h323-id BR2-CME h323-gateway voip bind srcaddr 200.200.110.2 end voice service voip allow-connections h323 to h323 allow-connections h323 to sip allow-connections sip to h323 allow-connections sip to sip fax protocol cisco h323 no call service stop call preserve sip bind control source-interface Loopback0 bind media source-interface Loopback0 registrar server expires max 3600 min 300 ! ! === debug message from gateway == BR2-CME#show
[OSL | CCIE_Voice] Frame Relay network
Hello, As I know, we have not to worry about the Frame Relay links/interface configuration on the LAB exam, besides the QoS. I mean, that the Frame Relay conenctivity is already preconfigured. Am I right? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] QoS 3750
Hello, What is the default Queuing method on 3750, when the mls qos is enabled globally, but no srr is configured. Is it FIFO? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] SRR
When we configure the SRR on a switch, does each ports has the following values by default: *srr shaped 25 0 0 0 * *srr shared 25 25 25 25* Even when I have not touched the Interface? For instance, I have configured auto qos voip on port fa 0/1, which will create SRR Buffer and other parameter globally, and will assing some SRR Shared and Shaped values for interface fa 0/1 for egress. But what about the other ports? Do they take automatically the shared and shaped values that I have already mentioned? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Output Queue mappings
Hello, As I know Packet to output Queue mapping in SRR is done based on QoS label, and QoS label is based on the trust. For instance is DSCP is trusted then the QoS label is generated based on DSCP, and if the CoS has been trusted then the QoS label is generated by the CoS value. Please refer to QoS configuration on 3560 Figure 31-1. So based on that, when the CoS is trusted, the output queue is using the CoS mappings, while when the DSCP is trusted, then the DSCP queue mappings are used. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] SRR
Did you check the show commands ? 2011/12/6 datucha123 datucha123 datucha...@gmail.com When we configure the SRR on a switch, does each ports has the following values by default: *srr shaped 25 0 0 0 * *srr shared 25 25 25 25* Even when I have not touched the Interface? For instance, I have configured auto qos voip on port fa 0/1, which will create SRR Buffer and other parameter globally, and will assing some SRR Shared and Shaped values for interface fa 0/1 for egress. But what about the other ports? Do they take automatically the shared and shaped values that I have already mentioned? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Nicolas MICHEL Ingenieur Réseaux CCIE #29410 Tel: +33 6 08 72 75 97 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] SRR
Sorry everyone, I have checked it and it is 25 0 0 0 and 25 25 25 25 by default. On Tue, Dec 6, 2011 at 8:18 PM, Nicolas MICHEL mcl.nico...@gmail.comwrote: Did you check the show commands ? 2011/12/6 datucha123 datucha123 datucha...@gmail.com When we configure the SRR on a switch, does each ports has the following values by default: *srr shaped 25 0 0 0 * *srr shared 25 25 25 25* Even when I have not touched the Interface? For instance, I have configured auto qos voip on port fa 0/1, which will create SRR Buffer and other parameter globally, and will assing some SRR Shared and Shaped values for interface fa 0/1 for egress. But what about the other ports? Do they take automatically the shared and shaped values that I have already mentioned? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ -- Nicolas MICHEL Ingenieur Réseaux CCIE #29410 Tel: +33 6 08 72 75 97 ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Switch Policy Map
Hello, Can you confirm please, that the Policy-Map on a switch by default has the statement of set dscp 0, unless we configure something else. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] CCIE Voice Lab Guidance Req !
Hi All i am planning to start studying for CCIE Voice. i need help to prepare my own lab at home. but no idea how to do that. i had prepare something on VM and GNS3 but PSTN is the problem. if i want to prepare in real means with real equipments than how many routers required and how to make that. i can arrange one 2821 with FXO, 2600 and one PoE switch. is this enough ? can anyone guide me how to start and how to prepare a good lab which can fulfill this need. -- Muhammad Zubair Mob : +973-36613334 / +973-66338466 Email: muhammad.zub...@gmail.com Skype: muhammad.zubairr ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Dtmf problem with MVA
I have MVA configured on my h323 router, with the appropriate dial peers as per the Cucm help pages. I am able to call into the piloting dn and I can hear the MVA application prompt me for my pin. When I press any digits, they are not recognized. I've tried to force a g711 codec and ensured Dtmf-relay is configured, but it doesn't change the problem. Has anyone run into this issue? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] Frame Relay Traffic Shaping
Yes FRTS uses average traffic shaping. Peak shaping can't be achieved in FRTS. Now setting Be to zero depends on the requirement. Zero means that you won't exceed your CIR. But if it has a value then you can exceed the CIR based on debt and compound debt concept as in policing with be value (single color dual bucket). Regards, Mohammed Al Baqari From: ccie_voice-boun...@onlinestudylist.com [mailto:ccie_voice-boun...@onlinestudylist.com] On Behalf Of datucha123 datucha123 Sent: Sunday, December 04, 2011 2:49 PM To: ccie_voice@onlinestudylist.com Subject: [OSL | CCIE_Voice] Frame Relay Traffic Shaping As I guess the FRTS uses the Average Shaping method, am I right? Also, when using shaping, either FRTS or any other variant, we have to always set Be to 0, when the Voice is also traversing that Shaper. Correct? ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] QoS for HWIC module
Hi, Just to make this clear. Trusting in HWIC module isn't similar to catalyst switches. For incoming, tagged packets, the Cisco EtherSwitch module honors the CoS value; the packets are buffered in a high-priority queue for CoS values 4 to 7 and scheduled for expedited forwarding. The low-priority queue is used for packets with CoS values 0 to 3. Untagged frames will use the default CoS value configured per-port. Regarding SRR configuration, HWIC support SRR with default settings, i.e. you can't tune it. This is the reason of not recognizing any command for SRR configuration. Hope its clarified now. Regards, Mohd Baqari From: datucha123 datucha123 [mailto:datucha...@gmail.com] Sent: Tuesday, December 06, 2011 12:28 PM To: Mohd Baqari Cc: ccie_voice@onlinestudylist.com Subject: Re: [OSL | CCIE_Voice] QoS for HWIC module Does it trust CoS or DSCP? Well, basically, I guess what does it trust, it trust just like the Router is trusting anything and relaying any QoS markings, am I right? But as for SRR, HWIC module interfaces does not undertand the command srr-queue or anything that begins with srr key word. On Tue, Dec 6, 2011 at 12:25 AM, Mohd Baqari baqari.voic...@gmail.com wrote: In HWIC trust is the default state. Also. srr can be configured. Regards, Mohammed Al Baqari Sent from my iPhone On Dec 5, 2011, at 5:12 PM, datucha123 datucha123 datucha...@gmail.com wrote: Hello, We can configur the L2 QoS on 3750 switch using SRR, Port based Trusts and etc. But what about the 4 port HWIC module? What kind of QoS must be done for that? I have tryed but the HWIC ports does not undertand the mls qos command. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com http://www.ipexpert.com/ Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com http://www.platinumplacement.com/ ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] Presence Deskphone
Hey guys, I am on the proctorlabs rack and kinda stuck and brainfreezed. I use hardware VPN and downloaded installed CUPC 7.0.1 on my laptop. I am able to login to CUPC however I can't switch presence status (shows OFFLINE) or go to Deskphone mode. Softphone and Voicemail appear to be working fine. Should be something simple that I can't catch - any help / ideas appreciated. Also, one weird thing with this client version is I have to exit and log back in anytime I switch desk / soft phone modes. Thanks. ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CCIE Voice Lab Guidance Req !
Suggest you use rack rentals to familiarize yourself with all the hardware and do a few labs. Then get some local hardware phones connecting to the pod remotely. You can then decide whether to do it yourself as it is expensive to put everything together. The rack rental guide shows all the hw sw needed. Good luck with your studies. On 7 Dec 2011, at 01:05, Muhammad Zubair muhammad.zub...@gmail.com wrote: Hi All i am planning to start studying for CCIE Voice. i need help to prepare my own lab at home. but no idea how to do that. i had prepare something on VM and GNS3 but PSTN is the problem. if i want to prepare in real means with real equipments than how many routers required and how to make that. i can arrange one 2821 with FXO, 2600 and one PoE switch. is this enough ? can anyone guide me how to start and how to prepare a good lab which can fulfill this need. -- Muhammad Zubair Mob : +973-36613334 / +973-66338466 Email: muhammad.zub...@gmail.com Skype: muhammad.zubairr ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
[OSL | CCIE_Voice] SIP Phone DID number
Hi All, I have configured a SCCP(Skinny) and SIP phone onto BR1-Site on my home lab and has noticed that the SCCP phone full DID range which is 6178631001 appears on the phone but not the SIP phone which is suppose to be 6178631002. Can somebody please tell me why the full number doesn't appear on the SIP phone. Your feedback is appreciated.thnx. Cheers Errol ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
Re: [OSL | CCIE_Voice] CCIE Voice Lab Guidance Req !
Emanuel i m scared buddy, i think 3rd world war started for me. right now i have 2821 with FXO card n another 2821 without. also i can arrange one or 2 2600 series. before that i had setup my virtual machines on my laptop which has 8Gb ram and simulation on GNS3 from Blue Print. but its very difficult to simulate PSTN scenario and alot of different stuff. man, please tell me the shortest and the easiest way to do that which is less expensive also. hope you understand On Wed, Dec 7, 2011 at 5:29 AM, Emanuel Damasceno aedamasc...@gmail.comwrote: Hello Muhammad, If you are serious about doing that, this is what you need (don't get scared) - 8 Phones, 7962 or UP - 1 2811 with 128MB of Flash, 1 PVDM2-16 or more, 1 VWIC-2MFT-T1/E1, 1 HWIC-4ESW - 1 2811 with 128MB of Flash, 1 PVDM2-16 or more, 1 VWIC-2MFT-T1/E1, 1 HWIC-4ESW - 1 2811 with 128MB of Flash, 1 PVDM2-16 or more, 1 VWIC-2MFT-T1/E1, - 2 2851 with 128MB of Flash, 1 PVDM2-64 or more, 3 VWIC-2MFT-T1/E1 - 1 3750 switch (3560 will do) - NM-CUE or AIM-CUE (I personally have a NM-CUE, I think it is better than AIM) - 1 server with enough processing power and enough ram. (mine is a xeon quad core with 8GB of RAM, when I put everything to run, it gets a little slow, but still fast enough for labbing...) I hope it helps... *Emanuel Damasceno* On Tue, Dec 6, 2011 at 3:05 PM, Muhammad Zubair muhammad.zub...@gmail.com wrote: Hi All i am planning to start studying for CCIE Voice. i need help to prepare my own lab at home. but no idea how to do that. i had prepare something on VM and GNS3 but PSTN is the problem. if i want to prepare in real means with real equipments than how many routers required and how to make that. i can arrange one 2821 with FXO, 2600 and one PoE switch. is this enough ? can anyone guide me how to start and how to prepare a good lab which can fulfill this need. -- Muhammad Zubair Mob : +973-36613334 / +973-66338466 Email: muhammad.zub...@gmail.com Skype: muhammad.zubairr ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com -- Muhammad Zubair Mob : +973-36613334 / +973-66338466 Email: muhammad.zub...@gmail.com Skype: muhammad.zubairr ___ For more information regarding industry leading CCIE Lab training, please visit www.ipexpert.com Are you a CCNP or CCIE and looking for a job? Check out www.PlatinumPlacement.com
