It looks a bit strange that it takes 40 seconds to respond to the DPD
requests and then they all come together?
Is there any kind of QoS / wan accelerators in the path?
Is this Ipsec over TCP? have you tried UDP?
Regards,
John
On Thu, 25 Oct 2012, Joseph Mays wrote:
We have a client on a
This one is a stretch...
Where I had intermittent disconnects when using the vpn client. The
location had wired and wireless. The user was connected to both and the
vpn client worked great, execpt for random drops of the connection. Had
them disconnect one of the connections and works great.
Are sub-interfaces supported on the ME3600x? Or is there some special formula
that I need to enable them?
Cisco IOS Software, ME360x Software (ME360x-UNIVERSALK9-M), Version 15.2(4)S,
RELEASE SOFTWARE (fc1)
License Level: AdvancedMetroIPAccess
License Type: Permanent
interface
Service instances are Cisco's 2012 way of doing subinterfaces:
conf t
int g0/1
switchport mode trunk
switchport trunk allowed vlan none
service instance 100 ethernet
encap dot1q 100
stuff
things
service instance 200 ethernet
encap dot1q 200
stuff
things
On 2012-10-26, at 1:37 PM, Eric A Louie
Hi Eric,
this is a switch.
You have to configure a SVI Interface.
conf t
vlan 55
int vlan 55
ip add X.X.x.X
if you want to use more vlans on a port you have to use switchport mode
trunk and you should remobe the comannd switchport access vlan 55.
Regards
Thomas
Are sub-interfaces supported
sub interface is not supported but you can use SVI to achieve the same.
-Waris
On Oct 26, 2012, at 10:41 AM, Eric A Louie elo...@yahoo.com wrote:
Are sub-interfaces supported on the ME3600x? Or is there some special
formula
that I need to enable them?
Cisco IOS Software, ME360x
ok, that's great, thanks Jason.
me3600-2(config-if)#service instance 55 eth
me3600-2(config-if-srv)#ip addr 192.168.112.1 255.255.255.0
^
% Invalid input detected at '^' marker.
me3600-2(config-if-srv)#ip ?
access-group Specify access control for packets
dhcp
IIRC, you have to map a service instance to a bridge domain and create an SVI
of the same BD value and apply the ip there.
--
Sent from my mobile device
On 2012-10-26, at 2:01 PM, Eric A Louie elo...@yahoo.com wrote:
ok, that's great, thanks Jason.
me3600-2(config-if)#service instance
A downfall for using the SVI on the ME3600 is you can not apply an
inbound/outbound policy map to the SVI.
We are applying them on the layer 2 trunk interface, gets annoying when
you can to aggregate the rate-limit between multiple interfaces.
(as for version
Hello,
Curious as to what everyone is using for config management for
switches. I have a few hundred 2960's and 3560's to manage on a
regular basis, and I would like to have something that can make mass
config changes. Not really looking for anything to monitor them as I
have that part covered.
Solarwinds or Rancid.
Scott
On Fri, Oct 26, 2012 at 12:51 PM, Dan Letkeman danletke...@gmail.comwrote:
Hello,
Curious as to what everyone is using for config management for
switches. I have a few hundred 2960's and 3560's to manage on a
regular basis, and I would like to have something
Thousands of switches...we use our own local scripts to put config/verify/audit
alan
___
cisco-nsp mailing list cisco-nsp@puck.nether.net
https://puck.nether.net/mailman/listinfo/cisco-nsp
archive at http://puck.nether.net/pipermail/cisco-nsp/
On Fri, Oct 26, 2012 at 1:01 PM, Scott Voll svoll.v...@gmail.com wrote:
Solarwinds or Rancid.
RANCID is really only good for config change monitoring out of the
box...and it'd be a pretty big leap I think to get it to do actual
configuration management. However, the clogin tool would be a place
KIWI CatTools (now owned by Solarwinds, I think).
On Fri, Oct 26, 2012 at 4:06 PM, Michael Loftis mlof...@wgops.com wrote:
On Fri, Oct 26, 2012 at 1:01 PM, Scott Voll svoll.v...@gmail.com wrote:
Solarwinds or Rancid.
RANCID is really only good for config change monitoring out of the
Hi,
As mentioned by others, Rancid is a popular tool for keeping track of
configs. Someone wrote a simple script which hooks into components
(clogin in particular) of Rancid to enable changes to multiple devices.
You define a list of devices and create a command file where you put your
required
Wrong url
--
With best regards,
Andrey 'sshd' Petrenko
xmmp\gtalk: andy.petrenko at gmail.com
skype: andy.petrenko
web: http://sshd.by
26.10.2012, в 23:46, Martin Clifton martin.clif...@vu.edu.au написал(а):
Hi,
As mentioned by others, Rancid is a popular tool for keeping track of
configs.
On 27/10/2012 5:58 AM, Andrew K. wrote:
A downfall for using the SVI on the ME3600 is you can not apply an
inbound/outbound policy map to the SVI.
You can apply inbound and outbound policy maps to a Service Instance
though (which are the ports that are facing your customer):
policy-map
http://www.ciscozine.com/2008/11/04/configuring-link-aggregation-with-etherchannel/
--
Zello: Garden4ever
NO STRESS
ECO ATTITUDE :D
On Thu, Oct 25, 2012 at 11:50 AM, Olivier CALVANO o.calv...@gmail.comwrote:
Hi
One of my supplier want that i active LAG on my Cisco Router
18 matches
Mail list logo
