Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
If you have measured DX4Win polling at 500ms please describe how you are doing that. The last time I experimented with polling, any Preferences setting below 2000ms was software-adjusted so that it never polled faster than every 2 seconds. -larry (K8UT) -Original Message- From: Radivoj Kar, F6GNZ Sent: Monday, June 24, 2013 2:26 AM To: Joe Subich, W4TV ; DX4WIN Refelector Subject: Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... best 73, Radi F6GNZ De : Joe Subich, W4TV li...@microham-usa.com À : f6gnz f6...@yahoo.com; microham micro...@yahoogroups.com Envoyé le : Samedi 22 juin 2013 15h02 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig If you are trying to configure a splitter function, you could try connecting HDSDR/OmniRig to Router's 2nd CAT port. Otherwise, your logger developer will probably need to provide an OmniRig option where OmniRig serves both HDSRD and the logger. Note, if you use Router's 2nd CAT port, it will be necessary to set any polling from HDSDR/OmniRig to the very minimum (slowest possible) to prevent overloading the control channel between Router and the MK II. 73, ... Joe Subich, W4TV microHAM America http://www.microHAM-USA.com http://groups.yahoo.com/group/microHAM support e-mail: supp...@microham.com On 6/22/2013 8:01 AM, f6gnz wrote: I have updated my shack with an SDR which I want to use for reception only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit only. I can control SDR with HDSDR program and synchronize FT1000MP/IC706 frequencies/modes via the Omni-Rig program interfaced with HDSDR. This combination works perfectly, but now my DX4WIN becomes useless as it can't read nor control the radio, saying ie_Open, device already open and Could not open COM4 for keying, ie_Open, device already open when I try to Start the Radio. So, I can't log the QSOs with related radio data (mode, freq's) nor use spot clicks to set up the TX/RX frequencies, nor control my antenna rotator. Is there any way to make the above combination work together??? Regards, Radi F6GNZ This list is for the exchange of information about the use and operation of microHAM products. Anyone with specific hardware support issues should contact microHAM support at mailto:supp...@microham.com. Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/microHAM/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/microHAM/join (Yahoo! ID required) * To change settings via email: microham-dig...@yahoogroups.com microham-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: microham-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] PSK-31 Receive Set-up
I’ve been using MMTTY with DX4WIN for years. Now I want to try PSK-31. I got stumped on the first step in the setup of PSK31 in DX4WIN manual. With the PSK31 window open I see no signals or noise on the displays. As a test, if I switch to the MMTTY window I see noise. I can change the amplitude of the display noise level using the Line-In soundcard slider. When I switch back to the PXK31 window there is no visual indication that audio is getting to the PSK321 window - even when moving the Line-In level from zero to max audio in. What do I need to do to get PSK31 to see audio in – a received signal? Transmit works perfectly. I need to get receive to work. Is there a squelch that needs to be set? 73, Bud W3LL w...@arrl.net __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] PSK-31 Receive Set-up
I’ve been using MMTTY with DX4WIN for years. Now I want to try PSK-31. I got stumped on the first step in the setup of PSK31 in DX4WIN manual. With the PSK31 window open I see no signals or noise on the displays. As a test, if I switch to the MMTTY window I see noise. I can change the amplitude of the display noise level using the Line-In soundcard slider. When I switch back to the PXK31 window there is no visual indication that audio is getting to the PSK321 window - even when moving the Line-In level from zero to max audio in. If I right click in the gray area of PSK31 window and select RX Volume no window opens. I’m using WIN7 with Real Tec sound. What do I need to do to get PSK31 to see audio in – a received signal? Transmit works perfectly. I need to get receive to work. Is there a squelch that needs to be set? 73, Bud W3LL w...@arrl.net __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
Hi Larry, In fact, I have never checked the real polling rate, but in preferences I have set it to 500ms and supposed it polls the radio at that rate. Now, when you asked, I counted number of polls of my FT1000MP on its CAT blinking indicator and it blinked 30 times in 32 seconds, i.e. 1 per second... Then I changed to 100ms and saved, it started blinking rapidly several times then resumed exactly as before, at 1 per second. I changed to 5000: it started blinking rapidly then resumed again at 1 per second... When I Stop the Radio in DX4WIN, CAT stops blinking (off). But when I exit DX4WIN, CAT lights permanently for about 10 secs, goes off in a fraction of second and goes ON for another 10 secs, because the microHAM Router polls it very fast and follows the frequency changes almost immediately. So, I think there is an interaction between DX4WIN and Router, making the polling time fixed to 1 seconds whatever is saved in Preferences ! Maybe Joe will tell us how it exactly works. 73, Radi F6GNZ De : Larry Gauthier (K8UT) k...@charter.net À : Radivoj Kar, F6GNZ f6...@yahoo.com; DX4WIN Refelector dx4win@mailman.qth.net Envoyé le : Lundi 24 juin 2013 12h00 Objet : Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig If you have measured DX4Win polling at 500ms please describe how you are doing that. The last time I experimented with polling, any Preferences setting below 2000ms was software-adjusted so that it never polled faster than every 2 seconds. -larry (K8UT) -Original Message- From: Radivoj Kar, F6GNZ Sent: Monday, June 24, 2013 2:26 AM To: Joe Subich, W4TV ; DX4WIN Refelector Subject: Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... best 73, Radi F6GNZ De : Joe Subich, W4TV li...@microham-usa.com À : f6gnz f6...@yahoo.com; microham micro...@yahoogroups.com Envoyé le : Samedi 22 juin 2013 15h02 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig If you are trying to configure a splitter function, you could try connecting HDSDR/OmniRig to Router's 2nd CAT port. Otherwise, your logger developer will probably need to provide an OmniRig option where OmniRig serves both HDSRD and the logger. Note, if you use Router's 2nd CAT port, it will be necessary to set any polling from HDSDR/OmniRig to the very minimum (slowest possible) to prevent overloading the control channel between Router and the MK II. 73, ... Joe Subich, W4TV microHAM America http://www.microHAM-USA.com http://groups.yahoo.com/group/microHAM support e-mail: supp...@microham.com On 6/22/2013 8:01 AM, f6gnz wrote: I have updated my shack with an SDR which I want to use for reception only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit only. I can control SDR with HDSDR program and synchronize FT1000MP/IC706 frequencies/modes via the Omni-Rig program interfaced with HDSDR. This combination works perfectly, but now my DX4WIN becomes useless as it can't read nor control the radio, saying ie_Open, device already open and Could not open COM4 for keying, ie_Open, device already open when I try to Start the Radio. So, I can't log the QSOs with related radio data (mode, freq's) nor use spot clicks to set up the TX/RX frequencies, nor control my antenna rotator. Is there any way to make the above combination work together??? Regards, Radi F6GNZ This list is for the exchange of information about the use and operation of microHAM products. Anyone with specific hardware support issues should contact microHAM support at mailto:supp...@microham.com. Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/microHAM/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/microHAM/join (Yahoo! ID required) * To change settings via email: microham-dig...@yahoogroups.com microham-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: microham-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to: http://docs.yahoo.com/info/terms/ __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post:
Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
Hi Joe, I have created an additional port for CAT 2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... But, I am still trying to make my setup work together: 1. To listen with HDSDR and automatically synchronize frequency of the related TX (FT1000MP/MK2 or IC706/MK1, depending on which one is switched ON and selected by the Router tabs. This works OK with HDSDR CAT to Radio via Omni-Rig 2. To be able to use DX4WIN for real time logging w. frequency/mode and to be able to click on the DX4WIN spot and set HDSDR RX frequency to this spot (and TX freq also via the HDSDT-OmniRig sync). This second feature did not work when I tried to check both HDSDR sync mode options (sync to and from Omni-Rig) as it created instability. NOW: I had an idea to make at least the spotting click work via the CAT control from DX4WIN to HDSDR: Radio 1 preferences of DX4WIN were set to Kenwood (protocol supported by HDSDR) on CAT COM 11 (created by Router) and the HDSDR option was configured to control HDSDR on the same CAT port. BUT: as soon I Start the Radio in DX4WIN, I get the message that the “port is already open” and “radio is disabled”. WHY?? What am I missing?? The corresponding Router configs for splitter functions are: FT1000/MK2/DX4WIN: CAT1 = COM4, CAT2:=COM2, PTT:=COM4 IC706/MK1/DX4WIN : CAT1= COM8, CAT2= COM3, PTT:=COM4 73, Radi F6GNZ De : Radivoj Kar, F6GNZ f6...@yahoo.com À : Joe Subich, W4TV li...@microham-usa.com; DX4WIN Refelector dx4win@mailman.qth.net Envoyé le : Lundi 24 juin 2013 8h26 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... best 73, Radi F6GNZ De : Joe Subich, W4TV li...@microham-usa.com À : f6gnz f6...@yahoo.com; microham micro...@yahoogroups.com Envoyé le : Samedi 22 juin 2013 15h02 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig If you are trying to configure a splitter function, you could try connecting HDSDR/OmniRig to Router's 2nd CAT port. Otherwise, your logger developer will probably need to provide an OmniRig option where OmniRig serves both HDSRD and the logger. Note, if you use Router's 2nd CAT port, it will be necessary to set any polling from HDSDR/OmniRig to the very minimum (slowest possible) to prevent overloading the control channel between Router and the MK II. 73, ... Joe Subich, W4TV microHAM America http://www.microHAM-USA.com http://groups.yahoo.com/group/microHAM support e-mail: supp...@microham.com On 6/22/2013 8:01 AM, f6gnz wrote: I have updated my shack with an SDR which I want to use for reception only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit only. I can control SDR with HDSDR program and synchronize FT1000MP/IC706 frequencies/modes via the Omni-Rig program interfaced with HDSDR. This combination works perfectly, but now my DX4WIN becomes useless as it can't read nor control the radio, saying ie_Open, device already open and Could not open COM4 for keying, ie_Open, device already open when I try to Start the Radio. So, I can't log the QSOs with related radio data (mode, freq's) nor use spot clicks to set up the TX/RX frequencies, nor control my antenna rotator. Is there any way to make the above combination work together??? Regards, Radi F6GNZ This list is for the exchange of information about the use and operation of microHAM products. Anyone with specific hardware support issues should contact microHAM support at mailto:supp...@microham.com. Yahoo! Groups Links * To visit your group on the web, go to: http://groups.yahoo.com/group/microHAM/ * Your email settings: Individual Email | Traditional * To change settings online go to: http://groups.yahoo.com/group/microHAM/join (Yahoo! ID required) * To change settings via email: microham-dig...@yahoogroups.com microham-fullfeatu...@yahoogroups.com * To unsubscribe from this group, send an email to: microham-unsubscr...@yahoogroups.com * Your use of Yahoo! Groups is subject to:
Re: [Dx4win] [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig
NOW: I had an idea to make at least the spotting click work via the CAT control from DX4WIN to HDSDR: Radio 1 preferences of DX4WIN were set to Kenwood (protocol supported by HDSDR) on CAT COM 11 (created by Router) and the HDSDR option was configured to control HDSDR on the same CAT port. You can not *under any circumstances* open the same port with two programs. You *must* have two ports - either a software splitter as provided by the CAT and 2nd CAT capability of microHAM Router (and some other logging packages), or the logger must use OmniRig to share control. I have never used HDSDR and am not a regular user of DX4Win so you're on your own with your custom software configuration. I know the concept is workable as I have run DXLab Suite, N1MM Logger or WriteLog with and NaP3 or PowerSDR IF Stage in that configuration on my own system. 73, ... Joe, W4TV On 6/24/2013 7:11 PM, Radivoj Kar, F6GNZ wrote: Hi Joe, I have created an additional port for CAT 2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... But, I am still trying to make my setup work together: 1. To listen with HDSDR and automatically synchronize frequency of the related TX (FT1000MP/MK2 or IC706/MK1, depending on which one is switched ON and selected by the Router tabs. This works OK with HDSDR CAT to Radio via Omni-Rig 2. To be able to use DX4WIN for real time logging w. frequency/mode and to be able to click on the DX4WIN spot and set HDSDR RX frequency to this spot (and TX freq also via the HDSDT-OmniRig sync). This second feature did not work when I tried to check both HDSDR sync mode options (sync to and from Omni-Rig) as it created instability. NOW: I had an idea to make at least the spotting click work via the CAT control from DX4WIN to HDSDR: Radio 1 preferences of DX4WIN were set to Kenwood (protocol supported by HDSDR) on CAT COM 11 (created by Router) and the HDSDR option was configured to control HDSDR on the same CAT port. BUT: as soon I Start the Radio in DX4WIN, I get the message that the “port is already open” and “radio is disabled”.WHY?? What am I missing?? The corresponding Router configs for splitter functions are: FT1000/MK2/DX4WIN: CAT1 = COM4, CAT2:=COM2, PTT:=COM4 IC706/MK1/DX4WIN : CAT1= COM8, CAT2= COM3, PTT:=COM4 73, Radi F6GNZ De : Radivoj Kar, F6GNZ f6...@yahoo.com À : Joe Subich, W4TV li...@microham-usa.com; DX4WIN Refelector dx4win@mailman.qth.net Envoyé le : Lundi 24 juin 2013 8h26 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig Thanks Joe ! I have created an additional port for COM2 and set Omni-rig to this port with 1200 ms polling time (DX4WIN polls each 500ms). All works fine except when I select both Sync from Omni-Rig and Sync to Omni-rig to be able to set TX to RX-ed frequency but also to set RX frequency by clicking on the DX4WIN spots. In this case my IC706 starts to walk frequencies, like it had gone to the scanning modeSo, must chose only one way sync... best 73, Radi F6GNZ De : Joe Subich, W4TV li...@microham-usa.com À : f6gnz f6...@yahoo.com; microham micro...@yahoogroups.com Envoyé le : Samedi 22 juin 2013 15h02 Objet : Re: [microHAM] MicroKeyer2, DX4WIN, HDSDR and Omni-Rig If you are trying to configure a splitter function, you could try connecting HDSDR/OmniRig to Router's 2nd CAT port. Otherwise, your logger developer will probably need to provide an OmniRig option where OmniRig serves both HDSRD and the logger. Note, if you use Router's 2nd CAT port, it will be necessary to set any polling from HDSDR/OmniRig to the very minimum (slowest possible) to prevent overloading the control channel between Router and the MK II. 73, ... Joe Subich, W4TV microHAM America http://www.microHAM-USA.com http://groups.yahoo.com/group/microHAM support e-mail: supp...@microham.com On 6/22/2013 8:01 AM, f6gnz wrote: I have updated my shack with an SDR which I want to use for reception only and keep my existing MK2, FT1000MP+ IC706 (for 50 MHz) for transmit only. I can control SDR with HDSDR program and synchronize FT1000MP/IC706 frequencies/modes via the Omni-Rig program interfaced with HDSDR. This combination works perfectly, but now my DX4WIN becomes useless as it can't read nor control the radio, saying ie_Open, device already open and Could not open COM4 for keying, ie_Open, device already open when I try to Start the Radio. So, I can't log the QSOs with related radio data (mode, freq's) nor use spot clicks to set up the TX/RX frequencies, nor control my
[Dx4win] Cabrillo file
Will DX4WIN export a log file in Cabrillo format? If so I haven't found out how to do it. I see in the export window there is a myriad of export file types but no Cabrillo. Any help would be appreciated. George W2YJ Sent from my Windows 8 Desktop __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] Cabrillo file
Here is a link to convert ADIF to Cabrillo. http://www.dxzone.com/dx23017/adif2cabr.html 73, Art W6KY www.w6ky.com From: George goofy...@rochester.rr.com To: dx4win@mailman.qth.net Sent: Monday, June 24, 2013 4:52 PM Subject: [Dx4win] Cabrillo file Will DX4WIN export a log file in Cabrillo format? If so I haven't found out how to do it. I see in the export window there is a myriad of export file types but no Cabrillo. Any help would be appreciated. George W2YJ Sent from my Windows 8 Desktop __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] Cabrillo file
Bottom line... Can't be done from DX4Win. You can do it though by taking the ADIF file from DX4Win and using one of the conversion programs to covert that file to a Cabrillo file for a specific contest. See Jim's - AD1C website I believe for the conversion program. The reason is a lot of the different contests that you would send a Cabrillo file to use different fields in a Cabrillo file. So you would have to program in each different contest Cabrillo file fields into DX4Win. A LOT of extra programming and they change quite often. Unlike the ADIF file... The thinking is DX4Win is a logging program and not a contest program. 73, Brian - NX0X -Original Message- From: George goofy...@rochester.rr.com To: dx4win dx4win@mailman.qth.net Sent: Mon, Jun 24, 2013 7:10 pm Subject: [Dx4win] Cabrillo file Will DX4WIN export a log file in Cabrillo format? If so I haven't found out ow to do it. see in the export window there is a myriad of export file types but no abrillo. ny help would be appreciated. George W2YJ ent from my Windows 8 Desktop __ X4WIN mailing list ome: http://mailman.qth.net/mailman/listinfo/dx4win elp: http://mailman.qth.net/mmfaq.htm ost: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net lease help support this email list: http://www.qsl.net/donate.html __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN.AWD award database release 3.37 - 25 June 2013
I have updated the DX4WIN.AWD file. This release contains 201 awards. You can download it from: http://dx4win.ad1c.us/awards/ But it's easier to use the DX4WIN Data Updater: http://dx4win.ad1c.us/updater The .ZIP file also contains a number of membership list files (plain-text files with a .list extension). These can be used to identify member calls in the DX Spots window. Please read the application note on Membership Lists for more information. You can read the full release notes here: http://dx4win.ad1c.us/awards/index.htm#3.37 Please let me know of any problems, etc. 73 - Jim AD1C -- Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] Updated DX4WIN.MAS1 master callsigns - 25 June 2013
I updated the master callsign database for DX4WIN. It now uses the master callsigns derived from the ClubLog database. You can download it from here: http://dx4win.ad1c.us/data/calldata.html#Master Better yet, use the DX4WIN Data Updater: http://dx4win.ad1c.us/update This database is based on the ClubLog Super Check Partial database released 23 June 2013. 73 - Jim AD1C -- Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN Membership List updated 25 June 2013
I updated the DX4WIN Membership List on 25 June 2013: http://dx4win.ad1c.us/data/calldata.html#Member You can get the latest version using the DX4WIN Data Updater. This release contains eQSL, LoTW and OQRS users (in that order). 73 - Jim AD1C -- Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
[Dx4win] DX4WIN.CTY country file Release #123 - 25 June 2013
The DX4WIN country file, DX4WIN.CTY Release #123 is now available from: http://www.country-files.com/dx4win/ You can read the release notes at: http://www.country-files.com/dx4win/release.shtml You can (and should) use the DX4WIN Data Updater to update the file: http://dx4win.ad1c.us/updater/ If there are any errors, please let me know. 73 - Jim AD1C -- Jim Reisert AD1C, jjreis...@alum.mit.edu, http://www.ad1c.us __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
Re: [Dx4win] Cabrillo file
Nope, will not. Not a contesting program per the author (other than the minor ability it has). Cabrillo needs special headers and format for each contest so would be too much worth anyway. Contest in another program (e.g, N1MM) and export ADIF from that and import into DX4WIN. You can output in ADIF and then convert to Cabrillo (I think) in some software. You enter all the header info when asked and it creates. Also, WA7BNM's site has a Cabrillo generator that does similar and you paste in your log (or type in your log) for small ones. I can look up more info if you do not find yourself or get in many replies. Dan KI6X -Original Message- From: dx4win-boun...@mailman.qth.net [mailto:dx4win-boun...@mailman.qth.net] On Behalf Of George Sent: Monday, June 24, 2013 4:53 PM To: dx4win@mailman.qth.net Subject: [Dx4win] Cabrillo file Will DX4WIN export a log file in Cabrillo format? If so I haven't found out how to do it. I see in the export window there is a myriad of export file types but no Cabrillo. Any help would be appreciated. George W2YJ Sent from my Windows 8 Desktop __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html __ DX4WIN mailing list Home: http://mailman.qth.net/mailman/listinfo/dx4win Help: http://mailman.qth.net/mmfaq.htm Post: mailto:DX4WIN@mailman.qth.net This list hosted by: http://www.qsl.net Please help support this email list: http://www.qsl.net/donate.html
