Bob Nielsen wrote:
Spectrogram - an audio spectrum analyzer that runs on a Windows
computer (there are others that will work on other OS's, but
doesn't everyone run Windows G).
Actually I am reading this on Linux.
I did my alignment on a Linux machine using one of the digital mode
Wayne,
Thank you for your very comprehensive reply.
The FT1000MP gets switched on about once a month, and I tend to switch between
bands and functions. This is not an excessive idle time, and I think that if
decent relays were fitted there would be no problem. All relays are not created
I am currently using my K2/100 to drive a linear amplifier (Yaesu Quadra).
I would like to use the ALC output voltage from the amplifier to control the
output from my K2/100.
Has anyone managed to do this, and any recommendations?
Thanks
Peter
___
Peter Bacon
www.g3zss.co.uk
use the ALC output voltage from the amplifier to control
This may not be such a good idea ...
Take a look at: SM 5 BSZ - The abominable ALC.
http://www.nitehawk.com/sm5bsz/dynrange/alc.htm
- Original Message -
From: Peter Bacon [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent:
Peter,
Not practical - you will have to be satisfied with controlling the level of
the drive to the linear.
In most cases, using ALC is not a good idea IMHO because it is normally set
to be an indicator of gain compression which is another way of saying
'beginning to operate in a non-linear
That was 200,000 with (memory check?) 1A on the contacts. You need to use
the mechanical numbers, since the current is 1A.
Dan / WG4S / K2 #2456
snip
Electrical: 200,000 operations min. (at 1,800 operations/hr)
/snip
___
Elecraft mailing list
Post
Hello fellow Polar Bears and all!
If anyone is interested in a Polar Bear Candy Tin, I can take a list for
orders. Click on the link below and look only at the Polar Bear Tin. It
contains Mint Ice Cremes. If anyone wants all five tins, that's ok
too. I will start an order list so we save on
Hi Evert,
First, sorry I missed you in the PACC! I played a
little in it, 160 to 20.
As to your questions:
1) Is there a noticeable difference in heat-sink
temperature when operating on higher bands?
There is a noticable difference if you're running into
a mismatched load. Also, it gets
Hi all,
Sorry for the bad link.
Here's a link to my website for a look at the
Polar Bear Tin and others. No price yet as this will depend on
the number of orders. Should be around $7.50 per tin with all sh
etc. Again this depends on the number. Once on the Polar Bear page, just
click on Polar
I would expect around 5-6 volts.
Bill Scovell wrote:
A signal from Down-Under.
What dc voltage should I expect at the output pin of the MAR-1? ---
Nigel A. Gunn. 59 Beadlemead, Milton Keynes, MK6 4HF, England.
Tel +44 (0)1908 604004 mobile +44 (0)7765 471661
e-mail [EMAIL PROTECTED]
Hi Folks,
My K2/100 (S/N 4787) is about 10 months old. My
question is at what point, or ever, should all the
initial alignments be repeated? There are several
reasons for asking the question other than electronic
components simply drifting a bit with age.
1. Recently I've noticed when it is
Jim,
The K2 does not seem to need periodic re-alignment because there is not a
lot of drift in the component values over time and the design is on the
conservative side, so it is forgiving of minor alignment errors.
BUT - If you want optimum performance, do take whatever steps necessary to
get
Hello,
My K2 # 1028.
I have a more or less often appearing problem. The pots for RIT/XIT, RF
gain, power are all the sames and become tired as trhe time went go : the
beomes too much play. I had this trouble at the XIT/RIT pot with following
effect : the frequency moves down or up as the play in
Hi Gang,
This should be and easy one. I have a K2, SN543, loaded with all updates
and firmware but no 100W. I've used the HM-2 with for a couple of
years for a couple dozen SSB contacts. When I plug my Heil boom set in
and key it with the foot pedal, the rig shuts off.
Does the resistor on the
Mark,
Just saying 'Heil boom set' is not sufficient information to tell me which
mic you actually have.
Is it the Elecraft MD2? Is it the Heil ProSet (if so, which one of these is
it)? If the mic was made for use with an Elecraft or an Icom, then it
should have an electret element in it, but if
Hello all, I have been building a K2 and now a KPA-100. I am using a solder
pot for tinning toroids and would like to know how often to replace the
solder in the pot. I have been skimming the top which removes flux and
debries. I used a 1/2lb off a flux core roll and found it contains too much
Is there any news on when the new amplifer/tuner kit is coming out? I tried
to ask Wayne and Eric but do not get responses from either. Tried via the
list and direct :(
If not, does anyone know of a decent 10-160 SS amp kit a guy can build or
good plans to homebrew one?
Thanks and 73,
I have a small solder pot, and have had a hard time tinning with it. I'm sure
the problem lies with the user (me) and not with the pot!
I originally used solder from a roll (with flux) as Rick says, but it became so
much of a mess that I purchased a rod of solder (I guess it weighs a pound or
When I last used a solderpot, my understanding is that you generally
*don't* have flux in the pot .. just solder. When tinning a wire, you
dip it in paste or liquid flux and then into the pot. Solder
manufacturers sell bar solder (with no flux) for use in solder pots.
de w1rt/john
On 2/13/06,
I run a Goot model 22C solder pot (small, about 1/2 lb capacity) - and
do not use fluxed solder at all! I use plain bar solder (available from
Mouser and others) cut up into pot-sized chunks, adding more when needed
(infrequently). I use a liquid or paste flux with the item to be
tinned.
http://jm.slove.org/gc/
With apologies to my German friends...
73,
Julius
n2wn
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
-- Original message --
From: Jim Wiley [EMAIL PROTECTED]
I scrape the dross (oxidized solder and flux residue) from the surface
of the solder bath as needed. I manufactured the scrapers by cutting
strips of 0.010 stainless steel shim stock from a
Hello all,
I have some camping gear that I don't use anymore on my qrp field trips.
If anyone is interested in the following items, email me.
$70.00 1ea. Hennessy Hammock Large
http://www.hennessyhammock.com/
**
$25.00 1ea.Standard Term-a-Rest 3/4
Revision 1.02 KX1 firmware is now available. If your KX1 is serial
#1373 or higher, you already have it. It will also be included free of
charge with the KXB3080 30/80 m module. (KXB3080 price and availability
will be announced later this month.)
In addition to support for the KXB3080 module
Rich,
I have heard on this reflector recently that the amp was about to go to the
Field Testers, so unless some major problem crops up, I would expect it to
be announced as available in 4 to 6 weeks.
WARNING - I have no 'inside track' on this and I am not one of the Field
Testers for the amp
How much power in and out you looking for?
If you want an amp for something like a K1 or KX1
there's a kit called the HF Packer that works from 160-10 and
really a fine little amplifier!
It will deliver 35 watts with about 1.5-2 watts of drive.
73,
Sandy W5TVW
- Original Message -
From:
Have been thinking of new amp,does any one know will it have its own power
supply and about what price range.? Sincerely Harold n5tog k2 1587
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
The KX1 doesn't have the ability to observe on-air signals when the AF
output is muted, since it uses audio-derived AGC. This means that the
scanning function has to be live -- that is, not muted, and
continuously scanning from memory 1 to memory 2. (The K2 has a
live-scan mode as well, in
Thanks for the info guys, I will have to try straight solder no/flux. That
will probably eliminate the smoke when at temp. So am I to assume that I
must strip the emamel first, then use paste and dip (again) to tin?
___
Elecraft mailing list
Post to:
From: Sandy W5TVW [EMAIL PROTECTED]
To: Rich McCabe [EMAIL PROTECTED], elecraft@mailman.qth.net
Subject: Re: [Elecraft] Amplifier status
Date: Mon, 13 Feb 2006 22:25:50 -0600
How much power in and out you looking for?
If you want an amp for something like a K1 or KX1
there's a kit called the
Thanks Ken,
About half the supply volts, that's what I guessed.
Looks like the Dunce's hat for me --- I left the Palm paddles connected while I
did a Spectrogram run on the filters --- think I must have given them a nudge
and transmitted into the N-Gen before I powered off!
We live and learn.
31 matches
Mail list logo