In RTTY contests we can define the 2 receivers as 2 different radios (2
instances of K3 in ports using same com port) I have not heard of anyone
doing this in any other mode and certainly not in mixed mode. But it might
be possible for the WriteLog code to be updated to allow this. Doesn't
happen
My guess is that there is something in you're bandplan settings in the HRD that
causes this behavior.
LA8OKA Martin
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Maybe some light would be shed if those who think the K2 is NOT a SDR would
detail why.
73, Mike NF4L
On Dec 23, 2012, at 5:55 PM, Rick Tavan N6XI rta...@gmail.com wrote:
I dunno, folks, we may be gilding lilies trying to define SDR. If software
handles modulation and demodulation, that's
The K2 is definitely not an SDR. The K2 uses traditional rf amps, mixers, if
amps, crystal filters in the if, and a product detector, followed by an audio
amp. Elecraft does offer an add on audio DSP option which works quite well.
JIm, W4ATK
On Dec 24, 2012, at 7:39 AM, Mike Reublin
Perhaps a bit more explanatory
The K2 is definitely not an SDR. The K2 uses traditional rf amps, mixers, if
amplifier, crystal filters in the if and a product detector, followed by an
audio amp, none of which are defined in software. Elecraft does offer an add on
audio DSP option which
My K1 RF board ceramic trimmer capacitors C13 and C20 have an outline shape
that differs from either that described in the K1 assembly instructions or on
the silkscreen outline on the RF board PCB. This is the same question that Dean
asked back on 10/27/12. Don's answer described trimmer
Hola,
E51E was running PSK31 the other day on 17m and was sending 'up' for
split operations...I tried to do this but the rig would not allow split;
yes I had done A=B to get both VFOs in proper mode and then held down
the split buttonmy workaround was to put VFO B up 1 kc, monitor the
P3
K3 works split just fine in DATA A mode. It is only PSK from paddles
(and FSK from paddles) that do not split. Have you tried XIT?
73,
... Joe, W4TV
On 12/24/2012 9:22 AM, cx...@4email.net wrote:
Hola,
E51E was running PSK31 the other day on 17m and was sending 'up' for
split
You know, it might just work. You have 2 entry windows and 2 rigs defined.
I am not home till Fri but will try it it then. Have to define 2 sets of
messages using only what keys you get. Would be killer if it works.
Jim K0XU Sent from my Xoom tablet
On Dec 24, 2012 5:01 AM, Jim Rhodes
My K1 RF board ceramic trimmer capacitors C13 and C20 have an outline
shape that differs from either that described in the K1 assembly
instructions or on the silkscreen outline on the RF board PCB. This is
the same question that Dean asked back on 10/27/12. Don's answer
described trimmer
Update on my low output issue:
I ran the TX Gain Calibration this morning, and everything passed with
flying colors.
I am seeing about a 4-4.5V drop across the radio when going from rx to
tx. Rx voltage sits at 13.8V, but when I transmit, voltage across the
rig drops to between 9 and 9.5V.
One other thing I forgot to mention in my last post - when I change
bands, I get the message GEX on the display of my K3. I can't find a
reference to that message in my K3 owner's manual, Fred Cady's book, or
the Elecraft web site. Can anyone shed any meaning on what that message
means? I'm
Scott,
I figure you have the blue bodied trimmers and not the older ceramic ones.
Look at them carefully - one end is rounded (that will be the wider end
with rounded corners) while the 'shorter' end has angular corners and a
flat between those corners. That is the 'flat' side and should be
Using a DVM or other self-contained voltmeter, measure the voltage at
the power supply end of the cable during Rx and Tx. Is the voltage drop
small (under 1/2 volt)?
Measure the voltage at the radio end of the cable (using the same
voltmeter) during Tx and Rx. Compare it to the K3
Wow. That will certainly explain the drop in RF power output.
I would not suspect corroded pins on the KPA connectors since resistance
there will limit the current the PA can draw and actually reduce the voltage
drop.
Are you looking at the voltage reported by the K3's display? If so, can you
IMPORTANT ADDENDUM/CORRECTION TO MY PREVIOUS POST ON THIS.
I wrote:
Take your ohmmeter and measure from the center, where the adjustment tool
contacts the capacitor. Measure to each of the two contacts, and find the
one that is shorted to the adjustment slot. That is the side you want to
be
Ian,
With that much voltage drop, I would strongly recommend you look at your
power supply and the power cable to the K3.
First measure the drop while transmitting right at the power supply. If
you have significant sag there, either your power supply is marginal or
the output terminals at
Ian,
Google didn't find anything on the GEX error when I looked. I searched the
Nabble archives and didn't find it there either.
Elecraft support should have that answer.
This is out of my pay grade but I would suspect the power supply rather than
the radio. I say that because I don't see that
The flat side on the board is indeed the grounded side - but as I
mentioned, you cannot see the flat on the silkscreen any more, you will
have to follow the diagram in the manual. The flat sides are not in the
same relative orientation - in each row of 4 there are 2 with the flat
to the left
This will work in N1MM Logger with two radios (SO2R)
Season's Greetings,
Ted W4NZ
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net]On Behalf Of Jim Rhodes
Sent: Monday, December 24, 2012 9:57 AM
To: DR
Cc: Elecraft Reflector
Subject: Re:
Don/all,
It is highly possible the culprit is my RigRunner, purchased in March of
this year. When I took it out of line, the voltage drop went from over
4V on tx to under 2V (13.8V down to about 12V). Current draw is .78 to
.82 amps on rx and 19.8 amps on tx. However, while the internal
Howdy K3' people:
I have a KAT500. The Auto green LED is lit. I have previously tuned to
the best it could get on 17m.
This morning it is drizzling. The 450 ladder can sometimes act up when
it is raining.
So I begin a JT9, one-minute long, sequence. Next I hear a little
chatter and see the
A happy Holiday season and a great and healthy new year to all. I just finished
my fully loaded KX3. I am having several issues with it. Elecraft is closed
today, so decided to ask other Elecraft users some questions. Here is the
first: I am having three issues with my new KX3 serial number
On 12/23/2012 11:27 AM, John Shaw wrote:
if the
KAT500 was passed the operating frequency information from the transceiver
instead of just band information that would elevate it from a good tuner to
a great tuner.
As a beta tester for the KAT500, I can tell you that 1) Elecraft says
that this
I'd check the accuracy of the meter, with nearly 20A being drawn on TX, I'd
expect 100W out of the rig...
Best regards, Tim Hague
Skype m0afj.Tim
Sent on my iPad
On 24 Dec 2012, at 16:51, Ian Kahn - Ham km4ik@gmail.com wrote:
Don/all,
It is highly possible the culprit is my RigRunner,
Bob, it sounds like rain is changing the characteristics of that ladder line
and so altering the tuning solution required at the KAT500.
The blinking MODE light says it's ready to tune once you apply enough RF
power. Five watts won't do it. The KAT500 cannot tune with less than 10
watts of RF
Might not be a 30W drop, but a matter of calibrations of both the
internal wattmeter (there is a menu item to adjust it) and the external
wattmeter.
If the output power is set to 100W and the internal wattmeter is
reporting 100W, then the K3 is happy. If in fact the output power is
only 70
Fellow Elecraft Enthusiasts,
I would like to take this opportunity to say Merry Christmas and Happy
New Year. I hope that you will be blessed with good health, happiness,
and that your Elecraft dreams will be fulfilled.
73Bob W7AVK
Don,
These are definitely not the blue-bodied trim caps. I'm familiar with those as
they are used in the KFL1-4, which I've already assembled. No confusion at all
as to how to orient the blue-bodied, angular-nosed trim caps.
The C13/20 trim caps I've now installed on my RF board appear to have
On Monday Claire used a Straight-Key to send:
-Original Comment---
The blinking MODE light says it's ready to tune once you apply enough RF
power. Five watts won't do it. The KAT500 cannot tune with less than 10
watts of RF applied (20 watts is required for the most accurate
You don't have to keep that power level, Bob. You only need it if the KAT500
needs to retune, and then only for the retune cycle. For that you might QSY
a few KHz to a clear spot although between five and twenty watts you are
only talking about a one S-unit difference in signal.
The next thing
We had a good net today with 31 participants over a 30 minute period. No
discussions. Have a very merry Christmas and a wonderful holiday season.
Here is the list of participants:
Station NameQTH Rig S/N
K5RHD Randy NM Flex 5000
WB9JNZ Eric
The KX1 has sold.
Thank you.
Happy holidays!
Mike AC6JA
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
So, it looks like I tracked down my low output issue. The problem
appears to be with my West Mountain RigRunner, not my K3. A big thank
you to all who offered guidance on getting this thing tested and
troubleshot.
Thank you, 73, es Merry Christmas!
--Ian
Ian Kahn, KM4IK
Roswell, GA
Scott,
Sorry I misread your question. Yes the side protruding is kind-of
square which makes it a flat side. The remainder of the body is round.
You apparently have them mounted correctly.
73,
Don w3FPR
On 12/24/2012 12:31 PM, Scott Krebs wrote:
Don,
These are definitely not the
+1) Elecraft says that this data is NOT available at the output of the
K3; +
The K3 can be polled for this data. Many loggers are doing it. There is
even some software that is polling data from the logger at the same time.
Keith
--
View this message in context:
Ian,
Any chance of borrowing another wattmeter for a sanity check on your
external meter?
It sounds like your external meter may be reading quite low.
19.8 amps on TX would indicate 100 watts or greater output.
73,
Don W3FPR
On 12/24/2012 11:51 AM, Ian Kahn - Ham wrote:
Don/all,
It is
The first rule in troubleshooting is to unplug everything that isn't
absolutely necessary to the equipment being diagnosed.
In this case all that would be needed is power, ant/dummy load and the K3.
Then start plugging things in until you find the offending device.
73 de Brian/K3KO
Ian Kahn
On Monday Claire used a Straight-Key to send:
-Original Comment---
You don't have to keep that power level, Bob. You only need it if the KAT500
needs to retune, and then only for the retune cycle. For that you might QSY
a few KHz
On CW or SSB I could try that. With some of
I have absolutely no complaints regarding the KAT500.
I have two sets of antennae connected to the KAT500. One set is an 8
position switch box and the other is an NVIS loop that covers all
frequencies from 2.2MHz to 28MHz used for short distance
communications on MARS.
The antennae on the
Sounds cool, and as noted is something we can do at least for RTTY, and
might work for other modes and mixed modes.
But given that you have to listen between CQs, that's a long time between
CQs in each mode:
CW-listen-phone-listen-CW-listen-phone...
I think you'd be better off just calling a
Bet it's the Power Pole connectors, meaning the installation of the connectors.
But if it is the RigRunner, West Mountain will take care of it.
Glad you isolated the problem!
On Dec 24, 2012, at 12:52 PM, Ian Kahn - Ham km4ik@gmail.com wrote:
So, it looks like I tracked down my low
Bad regulated power supply.
I use a MANSON EP-925 (also known with other brand names).
This handles 25 amps easy with just a few 0.1 of voltage drop.
After some successful mods it is stable within 0.05 V RX/TX 100 Watt at 13.80
Volt.
(If interested see my mods at
Forgot to mention, absolutely run the calibration again with the correct 13.8V
supply. Then address the power output - if it still exists.
On Dec 24, 2012, at 12:52 PM, Ian Kahn - Ham km4ik@gmail.com wrote:
So, it looks like I tracked down my low output issue. The problem appears to
be
I don't get this. How is the rig runner implicated? The power doesn't go thru
it...DC or RF. So are you saying the drive was insufficient? And if so, how is
that not easy to diagnose?
Sent from my iPad
Chuck, KE9UW
(Jack for BMW motorcycles)
On Dec 24, 2012, at 1:13 PM, Jack Berry
Bob,
You could easily turn on XIT and move your frequency up or down a bit,
then increase power to TUNE (set TUN PWR in the menu)
When it has tuned, clear XIT and you should be good.
73,
Don w3FPR
On 12/24/2012 2:01 PM, KD7YZ Bob wrote:
On CW or SSB I could try that. With some of these
Thanks Ted.
I wanted to do SO2V mixed mode with a single K3 during the 10 meter contest.
I had not seriously done a 10 meter contest in a while and I was hoping that
this was already perfected in N1MM or Writelog. I played around with it for
a little while but I could not get it to work
I don't get this. How is the rig runner implicated? The power doesn't go
thru it...DC or RF.
Of course it does- the Rig Runner is a DC power distribution panel.
-Bruce, N1RX
__
Elecraft mailing list
Home:
Oh sorry, I see that. I was thinking of those digital interface boxes.
Sent from my iPhone
Chuck (Jack)
On Dec 24, 2012, at 1:21 PM, Bruce Beford bruce.bef...@myfairpoint.net
wrote:
I don't get this. How is the rig runner implicated? The power doesn't go
thru it...DC or RF.
Of course it
It seems like I've heard someone suggest that spray-on car wax does a
good job of making the ladder line real slippery. I haven't tried it
yet, but I have two ladderline pieces on my NVIS loop. Twenty seven
feet of feed line and a ten foot stub at the opposite corner that
detune a bit in the
That would require taking over the K3's serial port. The KAT500 is not
connected to the K3's serial port. Most loggers would prefer to own the
serial port rather than relegate it to an ATU.
Dick, K6KR
-Original Message-
From: elecraft-boun...@mailman.qth.net
Hi,
The frequency data is not available on the *AUX* bus. On the serial port
this data is of course available but to make it available to KAT500 would
involve at least one PC software program. I have in mind to ask Larry
Phipps if maybe he could add a feature to LP-Bridge to feed the frequency
The KAT500 following the radio by frequency is not going to happen but that
would make a GREAT new generation auto tuner. IMHO
Keith, XE3/K5ENS
--
View this message in context:
http://elecraft.365791.n2.nabble.com/KAT500-and-OT-Is-a-tuner-using-VNA-feasible-tp7567559p7567643.html
Sent from
Hello again,
A simpler way that would only involve changes to the KAT500 utility would to
have the utility talk to both the K3 and the KAT500. Even if the K3 is
already busy talking to a logging program, LP-Bridge unmodified can fix that
conflict. So now we have just created more work for Dick.
LP-Bridge alone will not help. While K3 Utility can obtain the
frequency information through LP-Bridge, that information would only be
sent out the same serial port back to the K3 - nothing gained. Remember
that the KAT500 uses a different serial connection than does the K3, so
that data
What version of HRD are you using. Pre 6.0 has a lot of CAT control
problems. I understand that Elecraft has loaned a K3 to the HRD staff to
fix issues and I see significant improvement in the 6.0 beta release after
playing with it.
Merry Christmas All!
~73
Don
KD8NNU
-.- -.. ---.. -. -.
Hi,
I wish I had better drawing skills - a picture is worth more than a 1000
words. The utility would communicate with the KAT500 as it does now plus an
additional connection to the K3 - either directly or through LP-Bridge.
Changes would be required to the utility and the KAT500 firmware, none
I've logged a few bugs in HRD's bug tracking system about K3 rig control -
among them some problems with buttons not properly toggling functions, not
being highlighted as to state, the lack of a 6M and 2M band selection
button, etc.
So far a couple of my bug reports have been modified to read
Hi All
I have been building this K2 taking my time and I thought I was soldering
carefully.
All has gone well so far and I have got as far as the IF amplifier alignment
having completed VFO linearization etc with no problems and all readings
within spec. I followed the instructions for the IF
ab2tc wrote:
...the question is if it's worth doing to save that one little
squirt of RF needed to tell the tuner the exact frequency.
At present the KAT500 works exactly the same as the KAT3:
(1) On any band change or antenna change, the last-used LC settings
for that band and antenna
Happy Xmas guys and a healthy and prosperous New Year to all.
I am
a recent convert to the K3 with model 6990.
I am primarily a data mode operator (PSK31 etc. etc.) and my
K3 has the 2.8KHz and 250Hz 8 pole filters fitted and let me say its doing a
very fine job too. I use HRD version 5 which
Wayne wrote:
So what we're talking about now is whether it would be worth sending
frequency data from the K3 to the KAT500--at the time of keying--over
either the auxBus or the RS232 port. The answer, IMHO, is no. In
either case it would take approximately the same amount of time to
Hi everyone
I am looking for Elecraft KAT3 Internal ATU with 2nd Ant. Jack for the K3
Kit. Please let me know if someone have it on sale. Thanks and Merry Xmas!
Alfredo Vélez WP3C
__
Elecraft mailing list
Home:
During a contest and for many ops with headphones on you wouldn't hear the
relays. Make it an option.
As for the timing if the KAT500 tunes as the receiver is tuned timing is
zero.
73,
Keith, XE3/K5ENS
--
View this message in context:
Ray,
Check every component in the Pre-Amp circuit, including the relay.
Do you have the leads of T6 well stripped and tinned? If so, check to
see that the leads are in the correct holes.
After that look critically at the solder pads for those components
around the preamp circuit - look at
Keith-K5ENS wrote:
During a contest and for many ops with headphones on you wouldn't
hear the
relays. Make it an option.
It's a possibility. I'll look into it.
Wayne
__
Elecraft mailing list
Home:
My question is that I would like to be able to simultaneously decode
more than 2.8KHz (HRD is limited to 3.9KHz) of the ham band at once.
I have thought about fitting the 6KHz AM filter (there not being a
4KHz filter available). One part of me says that would work just
fine and the other part
I don't know about spray-on wax. I used to smear it with paste wax. Now I use
open-wire line.
On 12/24/2012 11:24 AM, Tom H Childers wrote:
It seems like I've heard someone suggest that spray-on car wax does a
good job of making the ladder line real slippery. I haven't tried it
yet, but I
I felt I must post some good news after all the negative comments
about various US companies.
I have been using WSPR for over a year providing a beacon to G3JKF who
is developing small loop antennae. It of course ties up my K3 (#194)
and my computer.
I came across a reference to W5OLF and his
Hi Group, Been searching the mailing list for a solution to turn on/off my K3
remotely via Ham Radio Deluxe or another means. Looks like there has been some
posts on using serial activity as a trigger to turn on the radio. Just
wondering if there has been any progress in this area or if someone
I do not have my K3 yet. I have been reading about it.
I would like to use it with an Ameritron AL82 in semi QSK (vox on).
I do not see an amp connection mentioned in the manual
What is the hook up for a non QSK amp to the K3?
Tks very much
Gerry
Ian,
I would suggest before suspecting anything in between the power supply,
check the voltage and the power supply terminals before tearing into
anything. You already know the transceiver shows load voltage under load.
If the voltage drops low at the supply then you have the culprit. If not,
Gerry,
As with any amplifier ---
Connect the K3 output coax to the AL82 input coax, and connect the K3
KEYOUT to the AL82 PTT IN (or whatever they call it).
Forget the ALC cable - instead, adjust the K3 power output to drive the
AL82 to its full output (or whatever you want below that level),
Change training below to trailing
73,
Don W3FPR
On 12/24/2012 7:08 PM, Don Wilhelm wrote:
In other words, semi QSK controls the training edge of the KEYOUT
signal, but does not change the leading edge. TX DLY will control the
leading edge up to the limit of its range.
Ian,
As a bottom up reader, I see you have plenty of advice already. I would
also like to point out in addition to what I posted below, I had an extra
set of fuses and a Red-Dee connect 45 amp distributor in line with the
battery backup/power supply and this alone added 1.5v drop. With those
Despite the potential for voltage drop, I would not forget the fuse at
the power supply end of the wire unless you are certain the power source
has adequate overcurrent protection built in. The blade type fuses with
tight fitting sockets will cause very little voltage drop. If the
connection
You need to provide a way to ground pin 5 on the aux connector. I do this
with a remoterig interface. Any remote relay will work. This turns on the
rig then the rig stays on even if the closure is momentary. To turn it off
you need to send it the power down command via the command serial port. A
Hi Ted,
But given that you have to listen between CQs, that's a long time between
CQs in each mode:
CW-listen-phone-listen-CW-listen-phone...
I think you'd be better off just calling a tighter cycle in one mode at a
time, or using true SO2R with a second radio/antenna (if possible). Just my
78 matches
Mail list logo