Love my KX3 but ran into some strange behavior as of late with some hangs.
Running MCU 2.25 / DSP 1.30 when trying to change ACC2IO settings, when I
turn VFOA to LO=Ptt the unit hangs on the LO=Ptt option - display freezes at
LO=Ptt and I can't PWR off using ATU/BAND-.
I've tried re-flashing
I am confused about the filters and the bandwidth display...
I get a display that has 2 bars on far left and right.
The Bandwidth widens and narrows the bars in the middle,
but the bars stay at the edges? Like this:
| || |
narrows to
| || |
but, why not
||
or
You have APF engaged. *HOLD* the XFIL/Dual PB button.
73,
... Joe, W4TV
On 2014-10-18 9:46 AM, Brian Short wrote:
I am confused about the filters and the bandwidth display...
I get a display that has 2 bars on far left and right.
The Bandwidth widens and narrows the bars in the
David,
What do you have connected to the ACC2IO jack? Is there possibly
anything there that could be holding that signal to ground?
73,
Don W3FPR
On 10/18/2014 9:27 AM, David - KI4UVC wrote:
Love my KX3 but ran into some strange behavior as of late with some hangs.
Running MCU 2.25 / DSP
I own a Digikeyer and acquired a second for the K3, used.
Having trouble with the install. Win7 recognized the device,
but only the USB Hub and Digikeyer devices. The Codecs
are not recognized, specifically.
I checked the jumpers to ensure RS-232 for the serial ports
and that part works.
My
Brian,
You have Dual Passband turned on - see page 33 in the K3 manual.
73,
Don W3FPR
On 10/18/2014 9:46 AM, Brian Short wrote:
I am confused about the filters and the bandwidth display...
I get a display that has 2 bars on far left and right.
The Bandwidth widens and narrows the bars in
The proper venue for individual microHAM support is supp...@microham.com
The used one only finds the USB Hub and Microham Digikeyer
(no CODECs nor 2 other drivers).
There are only three USB devices in the original microHAM Digikeyer:
one sound device - USB Audio CODEC, Generic USB Hub and
You are, of course, correct Joe.
Thanks to Joe, Don, and others.
That works better for now :)
On Oct 18, 2014, at 6:55 AM, Joe Subich, W4TV wrote:
You have APF engaged. *HOLD* the XFIL/Dual PB button.
73,
... Joe, W4TV
--
http://www.qsl.net/k7on/
NAQCC #0470 FP #2990
Nothing is connected to ACC2 currently - I was mucking around with menu
settings.
I tried reverting back to MCU2.23 and am having the same issue - radio hangs
at any change in ACC2 settings.
I didn't have this issue until I did the Extended Temp Calibration routine.
Radio is in the low 6000
I thought the K1 was the commercial version of the Sierra. Didn't the
Sierra predate Elecraft?
BTW, the K1 is about the neatest QRP radio I own, even above my K2. I've
built boards for every band 80M-10M, especially enjoy working from the patio
@ 1W into an EFHW on 20M. It's my go to rig
I have an apartment on the top floor of a 10-story building with a small
roof area accessible and restrictions on antenna size. I asked for
advice here about antennas, and got a lot of suggestions and help, so I
thought I would post my results.
I put up an R8 vertical on a small building
I use an Elecraft KX1 and an Anker Astro Pro2 LION battery when I go QRP in the
field. The combination works very well, and allows me to run the KX1 at the
full 3 watt level. However, the last two times I used this arrangement, I had
the Anker battery shut down on me. It would power right back
I'm downsizing since retirement earlier this year, will be on the road with the
travel trailer. These item need a new home instead of sitting packed away. I
have my KX3, PX3 along with the KXPA 100, it all fits nicely in the trailer.
The K2, s/n 6576, was built in late 2011 by Dale Putnam WC7S,
Here is the net report for the Elecraft SSB net from October 12, 2014. There
was heavy QRM from contests and other nets. We did a QSY up 1 kHz to 14.3045,
MHz, but it didn’t help much. We had 21 participants over 18 minutes.
Station NameQTH Rig S/N
Hello,There is a new release of Win4K3Suite available.
This release has a number of enhancements and fixes especially in the
Panadapter software.
Release 1.684 now correctly recognizes the IF shift that occurs when Weaver
demodulation is in effect in the KX3. In addition it allows setting of an
Just received my PX3,
Power cable has no fuse so I cannot hook up to my 50 amp supply What cord
do I need to purchase?
My main concern is I can not see a signal on it that I am listening to on
the KX3. I see spikes and noise floor but no signals. I can adjust DISP,
Average REF, SCALE, SPAN.
Carl TNX for responding so fast.
No I do not. Just turned it on and now I can see signals.
What else do I need to turn on in the KX3?
--
Jim K9TF
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Jim,
Did you read the manual's page 6, first item under figure 1, ie did you
turn on the RX I/Q function in the KX3?
73,
Peter - PA0PJE
Op 2014-10-18 20:09 schreef Jim GM:
Carl TNX for responding so fast.
No I do not. Just turned it on and now I can see signals.
What else do I need to
David,
Contact KX3support(at)elecraft.com to see if they can offer any
additional wisdom. If it has to go back to Elecraft for work, that
contact at support is the starting place to obtain an RSA.
73,
Don W3FPR
On 10/18/2014 10:53 AM, David - KI4UVC wrote:
Nothing is connected to ACC2
David,
I did not have my brain fully in gear on this situation before. The
GPIO input is just that - an input to a 3 volt logic device with only a
500 ohm series resistor. So there is nothing to make it either a high
nor a low level. In the digital world it is known as a 'floating input'
My brother, W8TXT, has a problem with his KX3. In PTT, when he presses XMIT,
the KX3 puts out 3 or 4 watts with the cw key still open. When the closes the
CW key it puts out 10 to 12 watts and stays at that level. In LSB, he hits PTT
and gets the same 3 to 4 watts out without an mic audio.
Does he want to use CW or voice mode? If he wants to use voice, the mic will
pick up whatever is in the room and transmit it.
Also, if he wants to operate with voice, he really needs to set it up with the
steps on page 15 of the manual. Really.
wunder
K6WRU
CM87wj
The weekly Elecraft SSB net meets tomorrow at 1800Z on 14.3035 MHz. I will be
net control from Oregon. Hope to hear you.
73,
Phil, NS7P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
23 matches
Mail list logo