Hi everyone,
Just wondering if there are recommendations out there for a case for the
KXPA100? I'm thinking along the lines of a Pelican case, but something
soft-sided could possibly work too. Waffling back & forth between a case
that just carries the amp & cables or a case that carries amp,
On 6/30/2017 12:55 PM, Fred Moore wrote:
All of my testing was done with places far removed from the mains, that
is why I need a generator to start with.
Mains power is NOT the only source of noise. Noise from electronic
sources is FAR more common, and we often bring a lot of electronic noise
WTB Elecraft P3 W/SVGA card
Please contact Greg (K9ON) at greg7412 at gmail dot com
Thank you
Sent from Mail for Windows 10
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
sorry about the blank response. It is late here and the fingers do not
work well.
Fldigi uses audio tones for keying, and you need to be in SSB mode
(typically USB or DATA A) to transmit on the proper frequency - CW
included - but I would expect twice the sidetone pitch.
Use DATA A mode
Jim; When using the Honda's I have no experience of relative location
to the antenna's causing a problem.
Also I am absolutely sure no one on this list would expect to hear noise
below the noise that is below the noise when they already had a high
noise floor for other reasons, and they are
I own two things that I consider as close to perfect as humanly possible:
My Elecraft K3, and My Honda EU2000i.
I've never had any issue with hash or RFI with my Honda. Decades ago, when
they first came out, there were scattered reports, but Honda quickly
corrected the issue. My Honda is
FWIW, I have the Honda EU2000i and have
used it in many situations where hash/rfi
would be unacceptable. I never heard any
hash with the K3 and when I used the 2000i
to power a McIntosh C2600 tube preamp and
MC275 amp, I never heard any artefacts
with the volume full with no signal, dead
Is this still for sale? I am looking for a K3 that has been mostly
stripped for migration to a K3s.
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
On 6/30/2017 6:19 AM, Fred Moore wrote:
I also have found no reason for any type of filter with Honda's..
additional savings. Also note that one brand the noise hash was being
emitted directly from the generator not the power line, a filter won't
fix that one.
This will, of course, depend on
Back in the good old days, when the Internet was an academic
toy, and the users were friends, the standard was, "Please reply
directly to me and I'll summarize for the list." This approach
should work nicely on this list as well. I've used it once or
twice myself.
73 Bill AE6JV
On 6/29/17
I keep getting this when sending to the list
Sorry, we were unable to deliver your message to the following address.
:
Remote host said:
550 Message contained unsafe content
(Heuristics.Safebrowsing.Suspected-phishing_safebrowsing.clamav.net)
[BODY]
73 from David
Over the last several years we have tested about 6 different brands of
inverter generators. Hash on all of them except the Honda's. I have
not seen any hash on the 1000, 2000, or 3000 generators. One brand had
hash over +20 on 40 meters. It was coming directly from the generator,
not the power
When you evaluate generators look at the continuous load that is what is
important. Lets compare two Honda units as an example the 2000i and the
3000i. The 2000i is rated at 2000 watts for 10 minutes and 1600
continuous, while the 3000i is rated at 3000 watts for 10 minutes and
2800 continuous.
In order to send CW in CW mode, the KX3, like any other amateur radio
transceiver, needs an on-off keying input to its CW key jack. In CW mode,
amateur transceivers do not respond to audio input.
fldigi's primary method of sending CW is to produce an audio tone from a
sound card (such as your
Thanks to Tom, Dick and all who offered suggestions, but nothing seemed to
cure the problem. As a last resort I began troubleshooting the PC by
disabling all startup programs and selectively disabling non-Microsoft
services installed at boot time. Although time consuming to re-enable them
hello don , hello to all ,
I will put everything in the box
I will not have time to work on the KPA100 before mid September
Too much work at the professional level
Thanks again for the help of forum 73 , Christophe F8ACF-56
De : Don Wilhelm
À : Christophe
Wanted : A K3 with ATU that is for sale that has had most of it's parts
migrated over by the owner to the owners new K3s. Preferably by the
original owner. Would prefer with owners manual, original box. Please
contact W6RLV, my email address is good on QRZ or by phone 747 3hundred 76
fifty eight.
Could not have said it better myself.
I realize that a lot of us get tired of the especially long,
uninteresting threads, especially if we don't own a Silverado or somesuch.
The flipside is that really good information is lost forever when
replies go off-list.
73 -- Lynn
On 6/29/2017 8:09
Bob,
Two things are possibilities.
1) There is a marginal solder connection on the Front Panel board that
has oxidized. Look at the soldering for RP1 and U2 as well as the rest
of the board.
2) The data in EEPROM has been corrupted. To correct will require a
Master Reset - BUT - that will
19 matches
Mail list logo