,
ragchew etc).
I'm afraid something is broken. I hope there's an easy fix and an explanation?
- Franki ON5ZO
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post
resistor over the input be better than a pure short (seen somewhere on the web)?
Would this work? I can't see why not. Would any other stuff be needed or
recommended (diodes, caps, MOV?) for RX protection?
All input appreciated. TNX / 73
Franki ON5ZO
, the amp and K3 will talk to eachother and that my m/H MK2R+ will keep
on working as it does?
That would be really 'neato' ;o)
73 de Franki ON5ZO
http://www.on5zo.be/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
Franki ON5ZO
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email
. I have had nothing but troubles with these
red tape lovin' kafkaesque bureaucrats, so I'd rather see the carrier handle
the customs part. That would be in favor of UPS.
Has anyone in EU tried USPS and if so are you happy with it?
73 de Franki ON5ZO
seconds
(DVM not really fast). I assume this is the DC blocking (series) capacitor
loading or discharging (when removing the 12V).
Should I worry about this? Can this hurt the K3 in any way? Or can I just go
along? Better safe than sorry...
TNX / 73 de Franki ON5ZO
http://www.on5zo.be
receivers to the same frequency
- connect RX antenna to AUX RF BNC
- set KRX3 to Ant = BNC in the config menu
Is that all there is to it?
TNX / 73
- Franki ON5ZO = OQ5M in contest
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
too after 9
months of mounting the option.
I assume the 2nd RX (aux RF) is protected against RF pickup from the TX
antenna?
73 de Franki ON5ZO = OQ5M
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help
Just to be sure - PSE CFM?
Suppose I order a K3 now with an RX antenna option, but have no interest in
the VHF module right now. I might add the VHF module later on.
So I need a KXV3A right now or I need to swap the KXV3 for a KXV3A when I
add the 2m module?
73!
- Franki ON5ZO
and hope to take the K3 out some day.
The bag does honor the rig!
Exemples and colors can be seen at: http://tinyurl.com/7lm3m5 or contacted
at elecraftcov...@rfwave.net
73 de Franki ON5ZO = OQ5M
__
Elecraft mailing list
Home: http
with the TS-850 which does not
have a lot of parameters (didn't even use compression on that rig) so I hope
someone has some advice on what parameters to tweak the K3 for success.
TNX / 73 de Franki ON5ZO = OQ5M
http://on5zo.spaces.live.com/
___
Elecraft
OK Barry N1EU, I just set these parameters to your values:
mic: 30
cmp: 20
TX EQ .20 +5
TX EQ .40 +2
TXG-VCE = 2.0dB
Now if I push the PTT I get the sound of a 747 taking off and full scale
deflection on the power meter... without even talking!
Per ON4WIX's advice I then tried:
CONFIG:TXG
later.
TNX again y'all!
- Franki ON5ZO = OQ5M
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
-is-the-best-setting-at-a-given-time?
73 de Franki ON5ZO
http://on5zo.spaces.live.com/
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http
and I don't hear any switching products on the K3.
Do you plan to power both K3's with one PSU? Or each rig a dedicated PSU?
73 de Franki ON5ZO / OQ5M
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
. Or is there an easy way to align the headers in both planes
and visually check before pushing?
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub
.
So my conclusion is: nothing comes out of the LINE OUT. I looked through the
manual but only found the LIN OUT level parameter which I cranked up to the
max but that doesn't fix it.
Any ideas? Am I forgetting something?
- Franki ON5ZO
___
Elecraft
.
It makes a lot less noise in the headphones when RX on a dummy load, that's
my very first impression.
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change
OK K3 connoisseurs, I've got some more information on my RTTY / line out
problem.
- K3 + line out = OK.
- microHAM hardware and software = OK.
- I tune to an RTTY transmission and have the K3 decode. The tuning aid
tells me I'm right on. I'm not using Dual PB and listen 300Hz wide on a
500Hz
Solved thanks to Ed W0YK, who told me to see if the K3's FSK pitch matched
the MMTTY mark.
It didn't, now it does and all works fine (3 modes).
My K3 can listen so narrow compared to the TS-850... I think I'm going to
love this rig when it gets hot on HF, expecially on CW.
73 de Franki ON5ZO
put in about 10 hours working at a very slow pace. Building was
fun. Halfway I overlooked two little screws that I reported MIA but they
showed up in the end. Great mechanical engineering!
73 de Franki ON5ZO
http://on5zo.spaces.live.com/
___
Elecraft
and clamp the crocodile on that sheet?
I found a antistatic thingy at an online salespoint for 80 Euro (+50$) ex
S/H, so I'm a bit reluctant because I have no further use for such a thing.
TNX for the input and 73,
Franki ON5ZO
http://on5zo.spaces.live.com
and free traffic of goods within the EU! TNX Julian
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net
Thanks guys for a lot of answers and good advice directly to me and on the
reflector. Much appreciated.
I know what to do now regarding the APP power cable.
BTW regarding APP in EU:
http://www.wimo.de sells APP and the crimp tool (go shop radio acc's
power supply acc's).
73 de Franki
to fit the cable from the PSU? There is
a German (ham) distributor for these things but a crimp tool costs 66 Euro
(approx 100$) which is a silly investment to crimp only one connector.
Is there an alternative way of crimping or fitting the PowerPole?
Thanks for info / advice.
73 de Franki ON5ZO
de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
http://mailman.qth.net/mailman/listinfo/elecraft
Help: http
About the only band that is somewhat usable from here is the 40m band.
30m at my sunset until 0100utc has been VERY hot this summer, with only a
rotary Fritzel triband WARC dipole at 10m high most of the time (unless the
tower was cranked up).
I experienced 30m being more constant in openings
except the VFO dial.
Then there are the variable filters coming out in the future,
PSE define 'variable filters'?
Well, apart from the filters my wish list has almost become an order form
;o)
73 de Franki ON5ZO / OQ5M
___
Elecraft mailing list
this might help you, should this be the cause of your problem. It
worked for me (and my employer HI).
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr
and a friend and built two
of these myself. Works just fine even up to 1kW @ 30MHz.
If anyone needs the article in PDF (1.6MB), drop me a line.
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post
working (resonance not to be found). Now I have an 80m vertical and a shorty
160m dipole, within 10m of each other and no problem at all (not even in
SO2R @ 1kW).
73 de Franki ON5ZO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must
and enjoy it by making
contacts. Don't worry if those first QSO's are a bit messy. We all had to
get passed that point and considerate CW operators will adapt to make you
feel comfortable.
Good luck and have a ball!
73 de Franki ON5ZO
___
Elecraft
to ship to EU when the next batch is available (CE
label)?
2) Is the aux RX input (beverages and RX loops) available in the 'standard'
K3/100? Or do I need an option (like ATU with 2nd Ant. Jack)?
Thanks for the input.
73 de Franki ON5ZO / OQ5M
33 matches
Mail list logo