not happen.
Gary Mitchelson
NC3Z/4 Pamlico County, NC FM15
NC AHIMT COML
SHARES NCS997
NC Deputy Auxcomm Coordinator - Statewide
www.mitchelson.org
On 3/9/2019 13:44, Jack Brindle wrote:
>
>> On Mar 9, 2019, at 9:14 AM, Gary NC3Z wrote:
>>
>> Connecting the RX directly to the
3/9/2019 3:36 AM, Gary NC3Z wrote:
>> It puts out strong spurs on 20-6M
>> with 10M being the worst.
>
> In addition to the possibility of a coax cable with a bad shield
> connection, another thought -- is your station properly bonded? Every
> chassis should be bonded
n cable connections and are
> sure they are plugged in properly.
> This sounds like a problem that needs to be addressed by the tech support
> guys. Be sure to give them a call on Monday.
>
> 73!
> Jack, W6FB
>
>> On Mar 9, 2019, at 9:14 AM, Gary NC3Z wrote:
>>
>&g
Connecting the RX directly to the antenna and the spurs are not there,
the spurs are coming from the KPA500, and only when the KPA500 is
connected to a radio (happens on all my radios connected to the KPA).
Have tried the amp on 220 and 120, same issue. The KPA500 can be
connected to a dummy
SN 3759 just received 2 days ago (kit form) and put in operational the
station. TX is fine, issue is on RX. It puts out strong spurs on 20-6M
with 10M being the worst. Tested on live antennas and dummy loads,
grounds on and off, all ancillary connectors removed, etc. So far this
is making the
In my opinion much, much better words should of been choose than
seriously misguided, they have connotations that one is an idiot.
Seriously misguided would be trying to run a 12V device off 120V.
I would of loved to see some data/research/reference as to why this wont
work, there are a
Retired Pro Audio Guy
On Fri,1/23/2015 4:50 PM, Gary - NC3Z wrote:
Provides more gain and improves the SNR.
Gary Mitchelson
NC3Z Davidsonville, MD FM18
NC3Z/4 Pamlico County, NC FM15
www.mitchelson.org
On 1/23/2015 7:33 PM, Gary K9GS wrote:
Just curious...what is the point of paralleling 4
Provides more gain and improves the SNR.
Gary Mitchelson
NC3Z Davidsonville, MD FM18
NC3Z/4 Pamlico County, NC FM15
www.mitchelson.org
On 1/23/2015 7:33 PM, Gary K9GS wrote:
Just curious...what is the point of paralleling 4 microphone elements?
On 1/22/2015 10:44 AM, Gary - NC3Z wrote
described has been exactly my experience. Using
the PX3 I tune to the left peak, and it decodes well every time.
Tuning to the center does not work. CWT has never worked well for me.
David
On Wed, Jan 21, 2015 at 2:59 PM, Gary - NC3Z nc3z.g...@gmail.com
mailto:nc3z.g...@gmail.com wrote
I wanted a desk mic to go along with my KX3 station. Wanted something
more portable than the Heil boom and mic I use on my other radio. I have
experimented with dynamic mics on the KX3 and didn't get the results I
liked but did get very nice results with using 4 CUI electret condenser
mic
Well one of the things I have found that the PX3 helps with is being
able to more accurately and quickly to tune in a PSK31 signal verse
using the CWT Tuning Aid. I set the PX3 span to 2 or 3KHz and tune the
VFO so that the PX3's cursor's bold line is on one of the 2 PSK signal
peaks. If you
Here are some numbers I measured, transmit was with a CW carrier:
TX Current
RX Current
Band5W* 10W*15W 20W 25W
With KXPA
60 1.17A 2.22A
Jim, I have also had these reports when I tried to use a dynamic mic
such as a EV664A and Heil PR22, it gets pronounced at the mic gain and
compressor is turned up. I don't think there is any setting you turned
on. Because of this I have gone back to electret mics. Will be watching
to see what
I use a Pelican 1400, but that is a hard case.
Gary Mitchelson
NC3Z Davidsonville, MD FM18
NC3Z/4 Pamlico County, NC FM15
www.mitchelson.org
On 12/18/2014 3:55 PM, Mark Tellez wrote:
Hello,
I am looking for a case that will protect my KX3. I have the sidekick
handles and cover attached and
This has actually been a topic of several discussions on the KX3 Yahoo
group. If you look at the KX3 on a spectrum analyzer you will see that
when the compressor is turned on that the TX BW goes from about 2.8KHz
to 2.4KHz. I have asked Elecraft if there was a way for another option
to be
Cool idea Wolfgang, it works well for the KX3 too. Thanks.
Gary Mitchelson
NC3Z Davidsonville, MD FM18
NC3Z/4 Pamlico County, NC FM15
http://www.mitchelson.org/
On 10/2/2014 11:44, dl2ki wrote:
Hi,
when working with the DS response string, i found an easier and faster
method to read the
I think the KX3 form factor works out well as a home station. The face
is larger than a lot of other radios and in my opinion the ergonomics
are better than the K3. My KX3 station (KX3 and KXPA100) is my second
home station to my FTDX5000MP and the the station I take to my second
QTH when we
Hello group,
I am very close to pulling the trigger on a KX3 and possibly the
KXPA100/KXAT100 combo. If I can swing the KXPA100/KXAT100 I think I
would not option the KX3 with the KXAT3 at this time. But I have some
questions.
The manual mentions that with the amp enabled but the power set
18 matches
Mail list logo
