Thanks, Don, Jim and Joe, for all information.
I am now looking forward to discover all the goodies that´s in
the P3.
Thank You
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/m
I have just bought the P3-kit to work with my K3 S/N 23xx.
According to the P3 manual, the Male – Female DE-9 cable
should be connected between the XCVR connector and K3:s
rear panel RS232 connector.
My present setup for the K3 is with Microkeyer2 as I am
working a lot of contests using N1MM+ fo
During the ongoing All Asia Contest, after a few hours of sleep, I started to
call Cq on 20m using my Acom 1000+ K3 at 50 W.
After about 20 minutes I noticed ERR 12Volt and the power went down to 5 W so I
switched off the K3 and power supply.
After some 15 minutes of thinking I restarted the powe
cabling so that
the PC is
connected directly to the K3 and that cable does not fit the K3 RS232 port.
I suppose I will have to order the KUSB-cable from Elecraft.
Any other suggestions?
Kurt/SM6BGG
- Original Message -
From: "Jim Rogers"
To: "Kurt Wiksten"
Sent: Thursda
I was trying to load new firmware to my K3. Present MCU version 04.51.
When started I got some Err message and the Tx lamp blinked and the K3 screen
darkend. I tryed to
switch the power off on the K3 but it did not work so I paniced and switched
the power supply off.
I have tryed to switch the po
Hi
I am using Logger32 and N1MM logging programs with my K3.
On RTTY (FSK-D) and CW I am using the microKeyer 2 from microHAM as interface
between K3 and logger 32 as well as N1MM.
To work digital modes both logging programs are using the MMTTY / MMVARI
modules for coding/decoding
This combina
Yes VOX was on!!
73 de Kurt/SM6BGG
--
Jag använder gratisversionen av SPAMfighter för privata användare.
1631 spam har blivit blockerade hittills.
Betalande användare har inte detta meddelande i sin e-post.
Hämta gratis SPAMfighter här: http://www.spamfighter.com/lsv
__
Please help!
I wanted today to use my K3 in the car, working some CW on 80m.
I am using a mobil whip antenna tuned to 3530. I have used this installation
several times before with success.
In the morning today I tested the installation, tuned the antenna, sent some CW
with the bencher and
everyt
Maybe this is not the right forum but...
I want to use my K3 in CW-contests using N1MM software.
I am using a HP-Laptop with Windows XP and the Elecraft KUSB USB to serial
converter.
When working CW I am using my Bencher manipulator connected to the K3.
How do I get the N1MM program to send CW via
Using my K3 in a portable/mobile operation with the radio connected to the 13.8
car-battery I made a follish misstake
and reversed the polarity. Result: Dead rig.
I suppose no one out there have made the same misstake but perhaps someone
knows what I should do to get
the rig back and functioning
I want to use my Acom 1000 PA with my K3
I am using the K3 internal bug and I have contected KEY OUT on the back of K3
to KEY IN on my Acom 1000
but the PA T/R relay is not closing at transmitt!
Is there someone using the K3 with Acom 1000 who could give me some advice
about how to get the two
wo
I am assembling my new K3 with S/N 2361
I am finished exept KPA3 100W Option.
Now performing the Configuration and Calibration tests everything seems to be
working just fine except when I
come to Low-Power (5W) TX Gain Calibration!
Switching through the bands, bypassing the ATU, with a connected d
I am assembling my new K3 with S/N 2361
I am finished exept KPA3 100W Option.
Now performing the Configuration and Calibration tests everything seems to be
working just fine except when I
come to Low-Power (5W) TX Gain Calibration!
Switching through the bands, bypassing the ATU, with a connected d
13 matches
Mail list logo