Sorry, I should have replied earlier on this - I think I remember Ron (wrote
assembly manuals) or someone else from Elecraft saying that the jumper would
not be included in the kit if you ordered a K3/100.
On 1/12/07 21:00, [EMAIL PROTECTED] [EMAIL PROTECTED] sent:
My RF board is missing the PA
Sorry, better ignore that, I've just seen the mail from Ron saying it should
be there etc.
Back to waiting ...
On 2/12/07 11:51, David Ferrington, M0XDF [EMAIL PROTECTED] sent:
Sorry, I should have replied earlier on this - I think I remember Ron (wrote
assembly manuals) or someone else from
Of [EMAIL PROTECTED]
Sent: Samstag, 1. Dezember 2007 22:01
To: [EMAIL PROTECTED]; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
Simon, et al,
Thanks for the quick responses. I thought that with all of us building
these over the weekend, there would be someone
]; [EMAIL PROTECTED]; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
Sorry, I should have replied earlier on this - I think I remember Ron (wrote
assembly manuals) or someone else from Elecraft saying that the jumper would
not be included in the kit if you
In a recent message, David Ferrington, M0XDF [EMAIL PROTECTED]
wrote ...
Sorry, I should have replied earlier on this - I think I remember Ron (wrote
assembly manuals) or someone else from Elecraft saying that the jumper would
not be included in the kit if you ordered a K3/100.
Thank you,
Jumper
Block.
Back to the workbench...and more frequent walks...
73,
Henry - K4TMC
-Original Message-
From: Ron D'Eau Claire [EMAIL PROTECTED]
To: [EMAIL PROTECTED]; elecraft@mailman.qth.net
Sent: Sat, 1 Dec 2007 11:23 pm
Subject: RE: [Elecraft] Elecraft K3 Support on the Weekends
- Original Message -
From: Gary Bartlett VE1RGB [EMAIL PROTECTED]
To: David Ferrington, M0XDF [EMAIL PROTECTED]
Sent: Sunday, December 02, 2007 10:22 AM
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
Sorry to add to the confusion, but #095 was ordered as a K3/100
Except the instructions call for the K3 to be tested as a 10 Watt unit before
installing the PA, therefore the jumper is necessary!
It is possible to install the PA from scratch, so if there is no jumper it's
not a show stopper.
73 Dave, G4AON
K3/100 #80
=
In a recent
Is Elecraft Support active on the weekends? No response received from
a late Friday afternoon note about a missing part.
My RF board is missing the PA Jumper Block. Any other K3 builders have
this problem? Is it safe to proceed with assembly?
73,
Henry - K4TMC
K3 #98
Support on the Weekends?
Is Elecraft Support active on the weekends? No response received from
a late Friday afternoon note about a missing part.
My RF board is missing the PA Jumper Block. Any other K3 builders have
this problem? Is it safe to proceed with assembly?
73,
Henry - K4TMC
K3 #98
Message-
From: Simon Brown (HB9DRV) [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Sat, 1 Dec 2007 3:22 pm
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
You can continue, you will not need it if you have the 100W PA. It
should /
could be on the mainboard anyway.
Simon Brown
.
73,
Henry - K4TMC
K3#98
-Original Message-
From: Simon Brown (HB9DRV) [EMAIL PROTECTED]
To: [EMAIL PROTECTED]
Sent: Sat, 1 Dec 2007 3:22 pm
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
You can continue, you will not need it if you have the 100W
PROTECTED]
Sent: Samstag, 1. Dezember 2007 22:01
To: [EMAIL PROTECTED]; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
Simon, et al,
Thanks for the quick responses. I thought that with all of us building
these over the weekend, there would be someone
Ed and Simon have it right. You can continue on, as they said, installing
the KPIO3 and selecting KPAio nor in CONFIG:KPA.
There *should* have been a jumper block pre-installed in case you were
building a low power K3. It's required in a low-power K3 to complete the RF
circuit when there's no
On Sat, 01 Dec 2007 16:00:35 -0500, you wrote:
Simon, et al,
[snip]
As an aside, it sure would be nice to know what changed from manual
revision to revision. That way I could just update the manual that
came with the kit originally. In my full-time job, when a procedure is
changed, there
While most revisions to a new letter involve incorporating the items shown
in the errata, there was an additional major change made between Rev B and
Rev C of the K3 Kit Assembly Manual.
The procedure was reorganized to allow builders with the KPA3 100 watt
amplifier module to install the KPA3
its printing I think I'll go kick the dog)
-Original Message-
From: Ron D'Eau Claire [EMAIL PROTECTED]
To: 'Elecraft Reflector' elecraft@mailman.qth.net
Sent: Sat, 1 Dec 2007 8:03 pm
Subject: RE: [Elecraft] Elecraft K3 Support on the Weekends?
While most revisions to a new
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED]
Sent: Saturday, December 01, 2007 5:24 PM
To: [EMAIL PROTECTED]; elecraft@mailman.qth.net
Subject: Re: [Elecraft] Elecraft K3 Support on the Weekends?
So... I am wasting my time trying to build my K3 with the Assembly
Manual
18 matches
Mail list logo