Mike,
While in data mode, press Menu, dial to MIC SEL, ensure it's set to Line
In not RPL or FPL (right or front panel), now the mic should
definitely not be live and if it is (and triggers VOX), you have a problem
with your rig and it needs to be fixed before you use data modes again.
The
Got it, Thomas. For some long forgotten reason I had MIC SEL set to MIC+LIN.
DOH!
73, Mike NF4L
On 1/27/2012 4:04 AM, Thomas Horsten wrote:
Mike,
While in data mode, press Menu, dial to MIC SEL, ensure it's set to Line
In not
RPL or FPL (right or front panel), now the mic should
Tim
I run fldigi with my K3, no need for any interface, just sound card
cables and RS232. The program is free from http://www.w1hkj.com/
You also need to download the K3.xml file (from the above page) and
it works... You don't need the companion program flrig as the fldigi
program itself reads
Tim,
Make sure you have MIC SEL on the MAIN menu set to PH+Line-In. This allows
the back line-in jack to be active for transmit/receive on the back panel
Line-In port. I also use the SignaLink with my K3 and don't have any
issues with this setting.
Hope this helps.
73,
--Ian
Ian Kahn, KM4IK
Tim,
You say that the PTT output from the Tigertronics jack goes to ground,
but that does not cause the K3 to go into transmit -- I think something
is awry in that area.
Think cable - have you checked the cable between the Tigertronics and
the K3 PTT jack? Pull the cable off the Tigertronics
This is a subject that has been aired many times on the server...(a) the
combination you are using (which is the same as mine) works just fine,
(b) you must be sure the K3 is IN VOX mode -- examine the display to
make sure that VOX shows above the AGC entry to the mid-left of the
screen. If
I have an ongoing, long standing problem with using VOX to key the K3 in Data
mode.
My sound card is a Creative USB dongle. I use a CM500 headset/mic, plugged into
the
back panel. If I get the mix of volume, line in level and VOX gain high enough
to
reliably key the rig, the smallest noise
I don't get it, when you are in DATA mode it takes the Line In signal and
ignores the microphone input if you've configured the rig correctly, any
input on the Microphone line should be completely ignored and VOX should
work 100%.
Still, on the K3 there is absolutely no need for any external
Data|AFSK A uses SSB mode internally, so the mic is live, I suppose. I have no
interface, that was the OP, not me.
73, Mike NF4L
On 1/26/2012 9:53 AM, Thomas Horsten wrote:
I don't get it, when you are in DATA mode it takes the Line In signal and
ignores
the microphone input if you've
After some nudges from the community prompted me to experiment further, I
changed MIC
SEL from MIC+LIN to rP.H ant turned MIC+LIN on. That seems to have fixed it.
73, Mike NF4L
On 1/26/2012 9:48 AM, Mike wrote:
I have an ongoing, long standing problem with using VOX to key the K3 in Data
Trying to run my K3 on PSK31 in data A mode w a tigertronics USB interface and
digipan software.
The box connects to K3 via line in/out jacks and the rear panel PTT jack. All
jumpers in interface are set correctly. When the software goes to TX, the
interface box goes to TX, and the phono
Try VOX and skip everthing except the computer, two cables for audio either
way, Digipan and the K3.
Mark, NØOKS
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
12 matches
Mail list logo
