You can also disable the 100 watt PA in the menu to prevent possible
over driving of any qrp rated accessories.
Martin, HS0ZED
On 28/5/63 11:03, Nr4c wrote:
The KPA3 is not used until you set PWR to greater than 12 Watts.
Sent from my iPhone
...nr4c. bill
On May 27, 2020, at 11:24 PM,
John, I have been using my K3 (sometimes together with my second one) for FD
at 100W for many years with excellent results. The power source is
pre-charged lead acid batteries which we change as needed. Sometimes the
battery in use is assisted by an ancient solar panel that probably doesn't
Thanks, Clark
Switching the SUB between main and Aux makes no difference: there is no AF
other than noise and nothing on the S meter when B SET is pressed.
Gareth
From: Clark Macaulay
Date: Wednesday, 27 May 2020 at 16:49
To: Gareth M5KVK
Cc: Grant Youngman , "elecraft@mailman.qth.net"
As someone who waited months after ordering when it was first announced, I
can say the wait was worth it. The integration with the KX3 and features
are well worth the wait.
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Are you sure about that Don? K3S's are still listed on Elecraft's
website and I know that they are still shipping during this pandemic.
https://elecraft.com/pages/k-line-transceiver-k3-k3s The K3S is a
great transceiver, I plan on keeping all of mine for a long time.
John KK9A
Don
I spent last evening checking the installation of the KRX3A. I did find one bit
of incorrect plumbing (in the cables that connect the KRX3A to the rest of the
K3S): however correcting it made no discernible difference.
The post-installation setup instructions pass OK and all the CONFIG menu
Sorry!
KRX3 Ant=bnc does not agree with both on MAIN.
Sent from my iPhone
...nr4c. bill
> On May 28, 2020, at 8:54 AM, Gareth M5KVK wrote:
>
> I spent last evening checking the installation of the KRX3A. I did find one
> bit of incorrect plumbing (in the cables that connect the KRX3A to
Hi
I emailed support over the weekend and have not heard back. Not sure if they
received the email or are backlogged in response due to COVID-19, so posting
here.
Looking for the resistor needed for mod to lower PSU fan speed on KPA1500
s/n 423
73
Dave wo2x
Hi Bill
The documentation around this is a bit confusing, but my understanding is that
this setting defines where the SUB gets its AUX antenna feed from. It can
either be BNC (the Aux RF socket on the back panel), or (if you have the ATU
installed and therefore two ANT sockets) it can get it
Ref pp 43 of KRX3 Istallation and User Guide Rev F Dec 22 2010
ALWAYS Set ANT = BNC if not connected to KAT3.
Clarification:I believe config selection ANT=ATU may be inserting
attenuation during transmit in the KRX3 signal path to provide protection.
Make sure KSYN3 tmp connections
And with that, lets let this thread take a rest for now. :-)
73,
Eric
Mooderator
elecraft.com
_..._
> On May 27, 2020, at 8:19 PM, Dave Cole wrote:
>
> Good, Fast, Cheap... Pick two.
>
> 73, and thanks,
> Dave (NK7Z)
> https://www.nk7z.net
> ARRL Volunteer Examiner
> ARRL Technical
Thanks Mark
Sadly, Changing the CONFIG KRX3 to be ANT=ATU makes no difference.
Gareth
On 28/05/2020, 16:08, "Mark Musick" wrote:
HI Gareth,
Sorry, I sent my previous e-mail to you before seeing this one.
You have jogged my memory.
I still believe KRX3 ANT= ATU is correct, but
You should update your status page to reflect this - all of these amps are
currently listed as 'Backordered' as of 28 May.
https://elecraft.com/pages/shipping-status
73,
John AE5X
https://ae5x.blogspot.com
As noted in my earlier email on this thread, we are
When I worked for Vectrol Inc, we designed a new production, battery forming
charger which is needed to make new lead-acid batteries, so I learned a
little about your typical "car" battery when talking to the engineers.
Granted, this was over 40 years ago, so battery technology has obviously
So where in the world is this modification described? Can't find anything on
the Elecraft web site.
Mike
K7PI
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of rocke...@gmail.com
Sent: Thursday, May 28, 2020 06:12
To: elecraft@mailman.qth.net
Subject: [Elecraft]
The config selection of ANT=BNC / ANT=MAIN does NOT actually select which is
used for KRX3 alternate antenna input. When AUX input cable of the KRX3 is
connected to the KAT3, the NON-TRANSMIT antenna used for the KRX3. Only one
can be physically connected to be used by the KRX3. If no ATU,
Only had a K3 w/out the KAT3, I’m not sure. But if Sub ant is bnc the you need
to connect its ant to the bnc Aux port I think.
Sent from my iPhone
...nr4c. bill
> On May 28, 2020, at 10:52 AM, Gareth M5KVK wrote:
>
> Hi Bill
> The documentation around this is a bit confusing, but my
It is not on their site or I would have done it already.
From what was posted on this reflector a few days ago the resistor value was
changed at some point in production.
Dave wo2x
Sent from my waxed string and tin cans.
> On May 28, 2020, at 9:57 AM, ex...@comcast.net wrote:
>
> So
Did you notice the 10-20 cars sitting around the FD site, each with a good
battery therein?
If you can find them, laptop supplies made for 12V car use will raise
efficiency some.
100W of solar will carry a station several hours Saturday afternoon and kick in
again for several hours Sunday, a
Hi, Gareth.
Well...you certainly have a mystery here. I found the documentation in the
Elecraft manual on this subject a little hard to follow; the book by Fred
Cady on the K3 is better and, if you'd don't have have it, I highly
recommend it.
I think you said on a previous post that you can hear
I think this only works if there is an ATU.
Sent from my iPhone
...nr4c. bill
> On May 28, 2020, at 11:37 AM, Gareth M5KVK wrote:
>
> Thanks Mark
> Sadly, Changing the CONFIG KRX3 to be ANT=ATU makes no difference.
>
> Gareth
>
> On 28/05/2020, 16:08, "Mark Musick" wrote:
>
>HI
Gareth,
The information you have been given is correct but it's a challenge to
wrap ones head around the details, a couple are subtle.
It is ultimately the items you have installed (the tuner, with the
second antenna port) AND the connection of cables to the KRX3 (which
connector source is
Hello to ALL
Win4K3Suite is good program but require additional com0com program
LP-Bridge makes virtual ports and you can connect all your programs to
these ports.
Win4K3Suite has full rig control, LP-Bridge not.
By the way, LP-Bridge2 works with other transceivers.
Best Wishes.
--
It’s E850824, KPA1500 PS Minimum Load Kit
Email Bruce, N7TY, he has an extra one and listed it on here for sale last
week
73, Lou W0FK
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home:
We still support repair on the K3 (and of course the K3S) as long as parts are
available.
73,
Eric
elecraft.com
_..._
> On May 26, 2020, at 12:44 PM, W6IPA wrote:
>
> Hi all,
>
> When the K3S came out there was a section on the FAQ regarding support for K3.
> I looked everywhere, and I
Thanks, Clark
I think I’m going to open her up again and test all the connecting cables.
Never mind, at least I get to use my K2 for a change
Gareth, M5KVK
From: Clark Macaulay
Date: Thursday, 28 May 2020 at 16:47
To: Gareth M5KVK
Cc: Mark Musick , "elecraft@mailman.qth.net"
Subject: Re:
Thanks, Ben
I'm going to open her up again and do another check on the seating of the KRX3:
it's quite difficult to be sure both the multi-way connectors are properly
mated. I'm also going to check continuity on all the leads.
Gareth, M5KVK
On 28/05/2020, 17:38,
Hi Lou
I think the PS minimum load kit is different than the resistor change to slow
down the PSU fans. I have already done the minimum load resistor which helps to
reduce the birdies on 80 meters.
What I am referring to is a resistor change done in production which slows down
the PSU fans
On 5/28/2020 5:02 AM, Charlie T wrote:
Since the IMD degrades at low DC supply voltages in our typical 12V powered
finals, if you must use a deep-cycle lead/acid battery, I suggest using one
of those battery booster things that MFJ and probably others sell to keep
the output up.
Have you
Thanks for the comprehensive reply, Rick.
I'm about to make a start on pretty much the same diagnostic approach. I'll let
you all know how I get on.
Gareth, M5KVK
On 28/05/2020, 18:00, "elecraft-boun...@mailman.qth.net on behalf of Rick
Bates, NK7I" wrote:
Gareth,
The information
True. I’ve been using one from TGE, the N8XJK booster with analog meters, for
years. Initially it generated a lot of crud, but after wrapping the leads with
appropriate ferrites, I see and hear ZERO RFI. With this booster I’m able to
keep my solar-panel charged AGM battery output set to 14v for
After I retire in three years, I was planning on ordering and building
the K2 and the KAT100.
I noticed the KAT100 has been discontinued. Hopefully the K2 will still
be around for a while.
Bob Richards, AA4AI
Sponsored by
Ditto on that with my mobile
n7wa
On Thu, May 28, 2020 at 10:44 AM James Bennett via Elecraft <
elecraft@mailman.qth.net> wrote:
> True. I’ve been using one from TGE, the N8XJK booster with analog meters,
> for years. Initially it generated a lot of crud, but after wrapping the
> leads with
I use my ductless hvac for both ac and heat. The unit is about 3 years old
and has variable speed motors in both the compressor and inside units. I
have never detected any rfi from the unit. I have a quiet environment, so
any noise is not being masked.
73, Dick, k7btw
Make sure the TMP connector center section on the boards is not broken or
push out. Easy to do if the TMP tip not lined up into the connector.
Also make sure that the pins from the SUB to the RF board are not missed
aligned.
Howard K6IA
Las Vegas
Thanks, Mike
It's a K3S, so it has the upgraded KSYN3As
Gareth, M5KVK
On 28/05/2020, 18:29, "Mike Harris" wrote:
Did I read at some stage that you do not have the internal ATU? That
being so you will not have selectable ANT 1 or ANT 2. That being the
case you will only have AN1
If the TMP cable was ever pulled on to unplug the connector, there is a better
than even chance the center conductor is broken.
Ben W4SC
Sent from Mail for Windows 10
__
Elecraft mailing list
Home:
An optimist believes we live in the best of all worlds. A pessimist fears
this is true.
John - n0hj
On Thu, May 28, 2020 at 7:12 PM Lynn W. Taylor, WB6UUT <
kx...@coldrockshotbrooms.com> wrote:
> Why do people always assume a dire future -- always the worst possible
> outcome?
>
> We all do
So much can happen in 3 years especially when talking about retirement ages and
I’d be inclined to buy the K2 now and build it now if that is a viable option
and it really is high on the bucket list.
Paul
W6PNG/M0SNA
www.nomadic.blog
> On May 28, 2020, at 3:23 PM, Fred Jensen wrote:
>
>
> glad I dropped ARRL membership 15 years ago
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by:
On 5/28/2020 3:27 PM, w4sc wrote:
If the TMP cable was ever pulled on to unplug the connector, there is a better
than even chance the center conductor is broken.
Yes, and I had the receptacle for a TMP cable come unsoldered from the
circuit board in one of my K3s.
73, Jim K9YC
Gareth --Maybe I missed this- But I have suffered thru the fun of SUB rx inbot
K3 anmd K3s ..
Maybe I missed it but I have never seen anything that says you can or cannot
hear a SIGNAL
in the SUB RX audio .All I have seen is you hear "noise" Forget all the ant
possibilities --
Fire up your
I for see more participation and way more activity due to the rule change.
Looking forward to working from home station, especially now that I have
one.
73,
Morgan NJ8M
__
Elecraft mailing list
Home:
You might want to have your wife purchase the K2 kit now and hide it
from you as a retirement present in 3 years. The K2 will likely remain
available for as long as the parts supply chain is intact. No way of
knowing when that may end but the K2 is around 20 years old.
73,
Fred ["Skip"]
Found the following NOS K2 Option. Selling.
$95 K2SB K2 Single Sideband Option w/K2KSB2 XTALS (14 Matched xtals) sealed
$95
$75 EC2 Cabinet opened but never unpacked,
panels still wrapped in brown paper with hardware bag.
Includes shipping USPS insured.
Reply off list please
http://www.arrl.org/temporary-rule-waivers-for-arrl-field-day-2020
73, David AJ4TF
--
Sent from: http://elecraft.365791.n2.nabble.com/
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Why do people always assume a dire future -- always the worst possible
outcome?
We all do this, and it's a bad habit.
I'm trying hard not to, and I've been a lot happier.
73 -- Lynn
On 5/27/20 4:45 PM, W6IPA wrote:
Eric,
Maybe the best would be to update the Shipping Status ,and other
k2/100 has found a new home-
Thanks 73
Dean
On Sun, May 10, 2020 at 9:52 PM Dean L wrote:
> FS, K2/100, CW/ssb, DSP board, early Serial#,
> Works as it should, could use updates $625, PayPal F, $16 USPS.
>
>
__
Elecraft mailing list
Likewise there seems to be a lot of pessimism when a product is in back order
status. If I really wanted a product, such as my K3S, there was a backlog of
orders. I placed the order and waited 3 months. No regrets in any aspect.
Bob, K4TAX
Sent from my iPhone
> On May 28, 2020, at 8:18
Two friends have ordered KPA1500's and got them in a couple of weeks. I'm
talking a week ago Tuesday. So apparently some stuff is going out and I have
received several items myself in the last two weeks. Just minor stuff but I
got it.
Ed.. AB4IQ
-Original Message-
From:
SOLD in record time about 15 secongs
Sent from Mail for Windows 10
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list
51 matches
Mail list logo