Manual says STP can be varied from 500 to 700 Hz. Mine will not go higher
than 650 Hz. What's up?
Bart de PA3GYU
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change,
Yes, indeed. The US has probably the highest tax rate in the world,
the better to support all those illegals getting benefits under 7
different names, I'm only halfway joking, we have a serious problem
with things like this! 73 de Alex NS6Y
On Jun 16, 2006, at 11:45 PM, David Douglass
The MC-43S Mike has been sold.
TNX for all how responded.
Kurt K0ARO
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Dave,
You brought up one point that is important. The person receiving your
sending must be able to copy it. It may sound neat to you to play with dot
and dash length and spacing, but will the other person be able to copy it?
On the other end of the pileup it is sometimes difficult to pull out a
How many hams have a 6-32 die in their tool kit to use on the paddle
screw?...And, if they did have one, it would not be necessary to thread it onto
the screw beforehand...
Jerry, wa2dkg
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You
Sorry to continue such an OT thread, but you US citizens should really
count your blessings...
In 2002 total tax burdens as percentage of GNP were:
USA 25%
Australia 32%
UK 35%
France 43%
Plenty more countries compared here http://tinyurl.com/fbrft
Regards
David
m0wam
-Original
Me and 'the boys' are heading out to play w/antennas (CF and EF/HW)
will be on KX1 20m/30m/40m -hope to find a few signals? Listening to
K1 early this AM I hear a few on 20m but little activity at 6AM MDT?
Should be on the trail and setup by 8?9AM MDT Will try 40M then 20m
and 30m last.
CUL
When bringing inner conductor thru the braid, it
can as said - be done by either un-weaving the braided
layer, or arching over the inner conductor - and
pulling it thru the braid via a small opening you make
in the braid itself.
One word of caution - using either method, especially
the hole in
Jeremiah McCarthy wrote:
How many hams have a 6-32 die in their tool kit to use on the paddle
screw?...And, if they did have one, it would not be necessary to thread it onto
the screw beforehand...
Jerry, wa2dkg
I for one have dies and taps from 4-40 to at least 3/8-24 plus a few
metrics.
Hi, Jesse:
There are several good ways to unravel the braid on coax...One way is to use a
sharp pointed tool, like an awl, a dental pick, an ice pick, or even a BIG
needle, and, starting near the end, inset the point into the braid and push the
point of the tool outward toward the end of the
In a message dated 6/17/06 8:09:53 AM Eastern Daylight Time,
[EMAIL PROTECTED] writes:
How many hams have a 6-32 die in their tool kit
Me!
also 4-40 and 8-32
Thread-a-nut-before-you-cut works well, though.
73 de Jim, N2EY
___
Elecraft mailing
When I lived in Luxembourg I found a solid plastic cased thing that has two
banana plugs which mate with a DMM and a BNC jack. With a BNC male connector
suitable for a probe's RG-174 cable it is easy to change probes without
moving banana plugs, and soldering to banana plugs is not an issue.
Folks,
In the past, I have had an add-on or plugin for Firefox that displayed the
solar flux and K index in the lower right corner of the Mozilla Firefox
browser. I have changed computers and now cannot find the link to this neat
add-on. Can anyone supply it?
73,
Don W3FPR
Checking a new email address
73,
Tom - [EMAIL PROTECTED]
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Don Wilhelm wrote:
Folks,
In the past, I have had an add-on or plugin for Firefox that displayed the
solar flux and K index in the lower right corner of the Mozilla Firefox
browser. I have changed computers and now cannot find the link to this neat
add-on. Can anyone supply it?
Hi Don,
Is this the one you're looking for?
http://www.n0hr.com/Propfire.htm
If not it is worth checking out, I have it running in my FF browser
right now! DF:75 A:10 K:2. Very cool.
--
73, Rod N0RC
On 6/17/06, Don Wilhelm [EMAIL PROTECTED] wrote:
Folks,
In the past, I have had an add-on
Rod, Dave, Sam,
I am back in business - I knew you guys would come through for me.
73,
Don W3FPR
-Original Message-
From: Rod N0RC [mailto:[EMAIL PROTECTED]
Sent: Saturday, June 17, 2006 10:26 AM
To: [EMAIL PROTECTED]
Cc: Elecraft reflector
Subject: Re: [Elecraft] Solar condx
Hi Rod, hi Don
COOL Software !
After installing and restart in the right corner of the status
bar appears: question
Then, after right-click on question and click to Full propagation
- OK appears SF75 A10 K 2
Is this OK ? I use V1.0.5.4 in german language
72/73
Uli
DF5SF
KX1 SN:1424
Rod
Another (free) hf propagation software I like to use is hfprop by G4ILO
go to: http://www.g4ilo.com/
select 'software'
then 'hfprop'
quote
There are many propagation programs already in existence. However, most of them
are written with the main aim of forecasting propagation over a specific
Tony, N2TK, wrote:
You brought up one point that is important. The person receiving your
sending must be able to copy it. It may sound neat to you to play with dot
and dash length and spacing, but will the other person be able to copy it?
On the other end of the pileup it is sometimes difficult
Hi all,
I've just completed k2 #5542, after a week of intermittent construction
(including 3 nights away from home on business - soldering away in a
hotel room!)
Had 1st QSO with Colin G3VTT on 30m - and serendipitously he was also
using a K2. Is that karma or mojo?
Looking forward to testing
You can change your settings so that you only get 1 Elecraft email digest per
day (with a table of contests and all the message text).
1, Go to
http://mailman.qth.net/mailman/listinfo/elecraft
2. Go to the bottom of the web page
2a. Enter your email address
2b. Click on the Unscribe or edit
Im having problems getting this set up. When I do the CW test (parallel
port) the software latches the K2 into transmit, which is only fixable by
rebooting the computer, or (sometimes) by launching LOGGER32 which works
fine with the K2 (Same cabling, same computer, same K2!).
It does this in
HFProp by Julian Moss is not FREE, It is shareware, sure you can down load
it and use it as an Unregistered, but I ma shure that Julian would
appreciate the donation.
HFProp is a very fine tool, so support shareware
73 KI4DGH
Chuck Gehring
-Original Message-
From: [EMAIL PROTECTED]
Sounds like a lot of RF in the shack, John.
de Joe, aa4nn
- Original Message -
From: john [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent: Saturday, June 17, 2006 3:05 PM
Subject: [Elecraft] Anyone using N3FJP Field Day SW w/K2?
Im having problems getting this set up. When I do
Congratulations John. Worthwhile keeping an eye on 10m for South Americans
in amongst the European Es, a PY is CQing away on 28.4896 MHz SSB as I type
this at 19:54Z.
73,
Geoff
GM4ESD
- Original Message -
From: John GM4SLV [EMAIL PROTECTED]
To: elecraft@mailman.qth.net
Sent:
Folks,
I find the digest format cumbersome to deal with. The posts for the day are
lined up one after another in one long email and I would have to scroll down
to find the one I want to look at. Yes, the Table of contents makes it a
bit easier, but ...
I have an 'Elecraft' folder under my
Sam Morgan wrote:
Another (free) hf propagation software I like to use is hfprop by G4ILO
go to: http://www.g4ilo.com/
snip
I have been corrected.
HFProp is not freeware, but in the current version there are no restrictions on
its free of charge use. However, the software will display
Trying to get Tbird to lose it's appetite for html.
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be a subscriber to post to the list.
Subscriber Info (Addr. Change, sub, unsub etc.):
Don, et.al.
On 6/17/06, Don Wilhelm [EMAIL PROTECTED] wrote:
Folks,
I find the digest format cumbersome to deal with. The posts for the day are
Ditto.
The solution I settled on was Google Gmail. http://gmaill.google.com
Advantages/Cool features:
o message download is not required, read
Got it completed and installed and its putting out 110+ watts on each
band but- I'm getting rf feedback on some bands. I use a Gap Titan
vertical and an 88' vee. The wire is quiet below 15m but much feedback
on 15, 12, and 10. The vertical is quiet on 80, 40, and 30 but gets bad
from
It was a rainy morning, 16 June 2006, quite unusual for the drought we have
been seeing in Colorado.
i was preparing to go up Trail Ridge Road in the Rocky Mountain National Park
(RMNP) but the road was closed because it was snowing.
i went up to the start of the road and decided to hike up to
Bob,
This is a case where counterpoise wires may help you identify the source of
the problem.
Cut a wire a quarter wavelength at each of the troublesome bands and fasten
one end to the KPA100 ground screw - if the problems go away, the problem is
in your antenna system. Knowing where to look for
Hi to the group and Gary at Elecraft,
A week or so ago I queried this group about a problem with no SSB audio when
transmitting. Several people offered helpful information. I've also
corresponded with Gary three or four times. The problem has been solved.
Note I said solved not completely
I can provide a little information as I recently bought one for use with my
K2 on a forth coming trip to Seattle USA.
The unit is made by XP at www.xpiq.com The specific model is not on their
site but the reference below looks similar.
Hurray!
KX1 #1516 just contacted KG8GW in the WVA QSO Party! Wow, this is a cool rig!
Onward to the KXB3080, KXAT1 and the K6XX tuning indicator.
72,
Glen, NK1N
K1 #2144
KX1 #1516
___
Elecraft mailing list
Post to: Elecraft@mailman.qth.net
You must be
FOR SALE:
KAT100-1 150W automatic antenna tuner for the K2 and K2/100. New in box,
not built. Bought new from Elecraft in May 2005. $200+shipping.
Please contact me off-list at:
[EMAIL PROTECTED]
73,
Chris WT1L
___
Elecraft mailing list
Post
Hi Jerry,
Tnx for the clothespin hint...I those banana plugs are a bear to solder.
Tom
k2 1103
wb2qdg
--
Teamwork is a lot of people doing what I say.
- Original Message -
From: Jeremiah McCarthy [EMAIL PROTECTED]
To:
38 matches
Mail list logo