Steve,
I'm just wondering if you use RX EQ with large gain settings. As I recall, the
K3 cancels those gains with the two narrowest Width settings (i.e., 50 and 100
Hz). This might account for at least part of the large increase in gain that
you experienced when you
opened up the Width
When I tune K3 to the carrier wave signal of a AM broad casting in LSB mode,
and then press NR, the AF output of K3 turns very very loud. AFV display will
turns from 1xxx to 5xxx when DSP is activated in this situation. Description
above is is a simulation of receiveing a sharp SSB signal in
David,
The LMC660 op amp can have a tendency to oscillate when driving a
capacitive load (see the LMC660 datasheet) although it is normally
stable in the K2.
Before replacing it, try the following steps - check after each one and
stop if no oscillation.
1) Flush trim the leads of U10 and the
Good thinking Chuck. I have the RX EQ set for band 4 at +2 and band 5 at +3.
The difference in volume is very slight. What I heard was FULL volume.
Steve Ellington
n...@carolina.rr.com
- Original Message -
From: ni0c n...@earthlink.net
To: elecraft@mailman.qth.net
Sent: Thursday, April
~
N2CQ QRP CONTEST CALENDAR
April 9 - May 10, 2009
~
PSK Flavors Contest ... QRP Category
Apr 11, 12:00 to 18:00 YOUR LOCAL TIME
Rules: http://www.podxs070.com/
I'd go into WINDOWS device manager.
start; right mouse click on my computer; that will get you to where
you can click on manage; then device manager... then ports
You will then see all the com ports
one of them might be a modem ,
but one will suggest a USB connection like prolific
Hello Jay,
I have found on Window Vista, when I connect the USB cable to the Radio
Computer, and the radio computer is turned on, the device Ports (Com
LPT) is added to Device Manager. Click on the device and the description will
appear. Prolific USB-To-Serial Bridge (Com 5). I now know
When ice freezes, it is called frozen. When glue hardens, it dries, and
concrete cures. What is it called when solder becomes solid again after being
in the liquid state.
73
Alan
W1HYV
_
Quick access to your favorite MSN
Wayne, et al,
Is there any way to have a continuous display of one of the functions
adjusted by the 4 multifunction knobs, e.g., power, mic, width, etc.?
The other day I was making amplifier adjustments and had to keep adjusting
the power knob. I would have liked the display of power on
I've always thought it was called cooling or solidifying.
- Keith N1AS -
- K3 711 -
-Original Message-
When ice freezes, it is called frozen. When glue hardens, it dries, and
concrete cures. What is it called when solder becomes solid again after
being in the liquid state.
What is it called when solder becomes solid
You said it yourself. Molten metal SOLIDIFIES when cooled. :)
David, W4SMT
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
When ice freezes, it is called frozen. When glue hardens, it dries, and
concrete cures. What is it called when solder becomes solid again after being
in the liquid state.
If that is what happened it is usually called a dry joint...
--
View this message in context:
Hope this is temporary. what's the cause?
--
Kind Regards / Mit freundlichen Gruessen
Chris Wagner KF6VCI
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post:
What kills solid state PN junctions is excessive power dissipation (heat).
You can abuse the breakdown voltage of a PN junction as long as the power
dissipated there is within the power dissipation range of the PN junction.
That's how Zener diodes work and it is why they have a power dissipation
This is probably 8 days too late, but the site may be down because of
a whole lot of new products being announced. Apple takes it's site
down while updating for new products. Elecraft is following he same
strategy. Look for a spectrum display that beats the one built into
ICOM7800 in
I have heard that there's an ATTT trunk line cut in San Jose that affects
service to the Santa Cruz County area, including Aptos. Telephones and
internet are affected.
73, andy, ae6y
- Original Message -
From: Lyle Johnson k...@wavecable.com
To: Chris Wagner kf6...@gmail.com
Cc:
AHA :-) I went back to it yet again and finally found the SUB POT option at
the
end of all the SQ MAIN number settings :-) Things are working just GREAT now!
I
guess I just need to be a little more adventuresome in hunting for some of
these
settings! MNI TNX for prompting me again to
At 10:06 AM 09/04/09, you wrote:
When ice freezes, it is called frozen. When glue hardens, it dries,
and concrete cures. What is it called when solder becomes solid
again after being in the liquid state.
Set?
john
__
Elecraft
Well, there is always 20 meters!!! :)
Russ Garrett
Kd7mpk
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Andy Faber
Sent: Thursday, April 09, 2009 10:19 AM
To: Lyle Johnson; Chris Wagner
Cc: elecraft@mailman.qth.net
-Original Message-
From: elecraft-boun...@mailman.qth.net [mailto:elecraft-
boun...@mailman.qth.net] On Behalf Of John
Sent: Thursday, April 09, 2009 10:20 AM
To: elecraft@mailman.qth.net
Subject: Re: [Elecraft] What is it called?
At 10:06 AM 09/04/09, you wrote:
What is it
Hope this is temporary. what's the cause?
Major disruption in the 831 area code area. Affecting telephones,
internet, etc.
73,
Lyle KK7P
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Trolling
Steve Ellington
n...@carolina.rr.com
- Original Message -
From: Alan Price w1...@arrl.net
To: Elecraft elecraft@mailman.qth.net
Sent: Thursday, April 09, 2009 12:06 PM
Subject: [Elecraft] What is it called?
When ice freezes, it is called frozen. When glue hardens, it dries,
Only familiar with Heathkit amps. Driven an SB200 SB220 with various solid
state
radios. Ic 730,TS 430,Ft757,IC746. I used an Ampkeyer between the radios the
Heath amps.
There are various interfaces. Some radios it's over kill but some need it.
It also a safety too. The Heath turns on 120v
Reminder, tomorrow, April 10th, will be the last day to submit your EQP 2009
score.
Please do so if you haven't already.
Submit results to eqp2...@elecraft.com
Tnx es 73,
Roger K7SJ K3 #75
Your EQP2009 scoring guy
__
Elecraft mailing
I worked in the discrete semiconductor industry for 30 years
(engineering, manufacturing, management) and that statement is simply
not true at all.
Zener diodes are designed to break down uniformly across the entire
junction, but most other semiconductors are not. A reverse voltage
Andy Faber wrote:
I have heard that there's an ATTT trunk line cut in San Jose that affects
service to the Santa Cruz County area, including Aptos. Telephones and
internet are affected.
Wayne will be cut off from distractions, able only to work on firmware! Who
knows what the
result will
It has been down all day for us. I am surprised such a failure is allowed -
someone will be in deep trouble.
--
View this message in context:
http://n2.nabble.com/Elecraft%27s-website-down--I-keep-getting-%22network-timeout%22-tp2612190p2612594.html
Sent from the Elecraft mailing list archive
I'm in Santa Cruz, and things like telephones (landlines), cell
phones, and DSL is down for a lot of people. Even 911 service (!).
Sigh. So much for redundancy on the part of the backbone providers, eh?
Jeff N6GQ
On Thu, Apr 9, 2009 at 11:03, AD6XY m.j.wil...@rl.ac.uk wrote:
It has been down
I have no idea of the cause, of course but as a retired utility
communications tech I'll tell you that anything is possible and
sooner-or-later will happen. A utility simply can't cover every
possible uh-oh.
My utility ... like most ... uses an extensive microwave system
for control of the
This link provided some information about the fiber optics line being cut.
http://www.mercurynews.com/ci_12106300?source=most_viewed
Looks like that is the problem.
Jerry, K4DZR
You have a right to seek justice! Click here to find
At 01:56 PM 04/08/09, Eric Swartz - WA6HHQ, Elecraft wrote:
When replying to emails on the list, please remember to edit down the copied
text to the minimum needed to retain context.
Might it be in order for folks reeplying to a digest message change
the subject line to that
of the thread,
The outage is affecting all land-line communications with Elecraft in
Aptos. Your only option until further notice is ham radio :)
73,
Wayne
N6KR
---
http://www.elecraft.com
__
Elecraft mailing list
Home:
On Thu, 2009-04-09 at 09:06 -0700, Alan Price wrote:
When ice freezes, it is called frozen. When glue hardens, it dries,
and concrete cures. What is it called when solder becomes solid
again after being in the liquid state.
I have the opposite question: What do you call it when solder
wayne burdick wrote:
The outage is affecting all land-line communications with Elecraft in
Aptos. Your only option until further notice is ham radio :)
So you and Eric are on what frequency?
--
73,
Vic, K2VCO
Fresno CA
http://www.qsl.net/k2vco
I think you FLOW solder.
CC Packet Cluster W0MU-1
W0MU.NET or 67.40.148.194
A slip of the foot you may soon recover, but a slip of the tongue you may
never get over. Ben Franklin
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On
The word here in Silicon Valley is that Verizon had a major fiber cable break.
It has taken out pretty much all their communications in the south valley down
into Monterrey. This includes telphone, cell phones, internets, and their other
communications. No word on when it will be repaired.
It was deliberate, apparently in both cases...
http://www.sfgate.com/cgi-bin/article.cgi?f=/c/a/2009/04/09/BAP816VTE6.DTLtsp=1
On Thu, Apr 9, 2009 at 13:13, Jack Brindle jackbrin...@earthlink.net wrote:
The word here in Silicon Valley is that Verizon had a major fiber cable
break. It has
Well, at my place when it has cooled, it is called soldered.
Then we go on to the next step...
Jack Brindle, W6FB
-Original Message-
From: Adam Koczarski k3...@k3ark.com
Sent: Apr 9, 2009 10:25 AM
To: 'Elecraft Reflector' elecraft@mailman.qth.net
Subject: Re: [Elecraft] What is it
My K3 display shows ERR KEY when I turn it on. It's been working flawlessly
until now and no recent changes have been
made.
1.No programs are running on the computer. ERR Key is displayed on the K3
2.If I shut down the computer the ERR Key turns off partway thru the
Windows is Shutting
I'm probably over thinking this, but when solder changes from any state to
any other state, it's still called solder.
: )
Tom
-Original Message-
From: elecraft-boun...@mailman.qth.net
[mailto:elecraft-boun...@mailman.qth.net] On Behalf Of Jack Brindle
Sent: Thursday, April 09, 2009 4:51
Did you check your CW key and/or paddle? I have had that issue when the plug
was slightly askew or if it was making contact. The error code indicates a
closed connection somewhere. Also check the cables to your amplifier (if you
ahve one in line).
Lou, W0FK
My K3 display shows ERR KEY
It was deliberate, apparently in both cases...
http://www.sfgate.com/cgi-bin/article.cgi?f=/c/a/2009/04/09/BAP816VTE6.DTLtsp=1
So the communications capabilities for a few million people are routed through
some unattended vaults in public places and there's
My K3 display shows ERR KEY when I turn it on.
Try disconnecting all cables from the K3 except the antenna and power
(obviously!) and see if the symptoms persist. If they don't, plug in one cable
at a time until the problem returns and go from there. Alternatively it could
be a problem
I think this thread has gone about to the limit, but, soldering is bonding
materials together with a eutectic material, in this case usually a lead/tin
based 63/37% material. Soldering/heating is what you do to accomplish the
act. Nuf said.
Mel, K6KBE
--- On Thu, 4/9/09, NG3V
OK, here the deal. My K2 S/N 6698 doesn't have the same freq offset on
all the bands. How can I program that so it is dead nuts on every band?
Here's the freq measurement spots and what the radio is showing as a
center freq using Spectrogram.
Signal freq then radio's displayed freq...
1.9
Bud,
If the K3 is powered on with a KEY(or paddles) or PTT closure, ERR KEY
will result, and will not transmit until the condition is cleared. (but
connect a dummy load just in case).
I am not certain the LINE IN has anything to do with it, but if VOX is
on, the K3 can be keyed with the LINE
Mike,
First there is up to a +/- 20 Hz tolerance that can be attributed to the
K2 DAC, so dead nuts on may not actually be achievable, but you can
get close. First question is - what are you using for a reference? How
much do you trust its frequency accuracy? That is one potential source
Alan,
If I am working on a radio, I would call it DONE - go on to the next
one. :-D
Now... if a drop of molten solder falls on the floor ?? (is that
akin to a tree falling in the forest?)
We now return to our regularly scheduled broadcast.
73,
Don W3FPR
Alan Price wrote:
When ice
At the eutectic, the solidus and liquidus temps are the same
Gil
- Original Message -
From: NG3V n...@comcast.net
To: 'Jack Brindle' jackbrin...@earthlink.net; 'Elecraft Reflector'
elecraft@mailman.qth.net
Sent: Thursday, April 09, 2009 6:30 PM
Subject: Re: [Elecraft] What is
Well it looks like my K3 won't talk to my Steppir anymore. I saw a post a while
back where a gentleman was having a problem. Y cable, baud, all is ok. I
haven't used the Steppir or the radio in a week or so. Been busy farming. Any
suggestions? It's been working on this K3 and my old one for a
Eutectic only applies to the 37/63 solder alloy.
Eutectic infers two things - 1) it is the alloy with the lowest
temperature melting point, and 2) there is no plastic state, meaning
it goes directly from a liquid to a solid with no plastic state in between.
The second point is the most
Hi,
I have a KX1 with 30/80 module and ATU that need to built, but I have
optic neuritis which makes me impossible to built it my self. I am looking
for a person that can built my KX1. I will pay if the fee is beyond my
budget.
--
George Rebong
KE6TE
See if you can isolate the problem - Turn off the K3 disconnect the computer
from the K3, turn it on and check the config menu setting for PTT-KEY. Turn
both PTT and KEY to OFF. Turn off the VOX. Turn off the K3 and reconnect the
computer. Turn on K3 then start up computer. You should be ok.
FW ver 3.06 - audio increases to rock concert levels on s-9 CW signal when NR
is switched in. NR is unusable now for me - same on SSB also.
Gill
hello all,
Anyone try this: listening a S7 to S9 signal (SSB) on any band with
your headphone, at this time, try to
enable NR, you will
Not only that, but the major electric feeders are also run out in the
open! Long-distance transmission lines, whether they be for
communications, power transfer or car/truck/train throughways are
necessarily run through non-secure areas, in most cases in the open.
It would be extremely
Paul, G4AFU asked Rose to make him a covers for his
K3 / ACOM pair and there are now two photos of them
on her URL at: http://tinyurl.com/7lm3m5.
It looks like a -nice- amplifier!
73! Ken Kopp - K0PP
elecraftcov...@rfwave.net
__
56 matches
Mail list logo