Hi All
We are waiting for the KX3 SYNC-AM function.
How many months does it take for a debut SYNC-AM?
73,
JE0LFI / nakamura
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Does this happy to anyone else with the new TX Monitor…?
My TX monitor sensor sits between my KPA500 and the KAT500 and since I have
installed it and had it up and running I have had more than my average spurts
of high SWR. For example, a key down may cause this spurt but just a moment
later
Do any of you new K3s owners have one of my
DXpedition K3 cases with the foam end cap kit?
If so, do the end caps fit the K3s OK? I don't think
there are any differences that would impact the fit
of the front or back end caps, but I'd like to conform
this.
Thank you, and ...
73!
Rose - N7HKW
My P3TXMON scope display is not performing as it should, while I am talking
in SSB mode.
Frequently the display will go to a straight line with vertical signals that
are very narrow.
It looks almost like it is switching to a very wide span or the time base is
changing frequency.
This will
Problem solved. Internal antenna routing messed up completely after
upgrading to the latest firmware. I've reloaded an old configuration
saved with a very old firmware (from May 2013) after the upgrade. That
was a bad idea.
Call me SRU... (stupid radio user) :-) ... my fault.
Thanks to all
Gents,
with the last firmware release I'm struggling with diversity mode. I was
running diversity for a very long time without any issues on my Xpol EME
system (144 MHz). The main RX is fed with the H-Pol signal from my
transverter #1 via KXV3-A, the sub RX is fed with the Vpol signal from
Brian,
it is MCU 5.29 from June 16. 2015. I didn't try the latest beta yet.
Before I roll back to a former FW I'd like to share my thoughts and
experiences cause its perhaps me doing something wrong.
73 Udo, DK5YA
Am 11.08.2015 um 13:34 schrieb brian:
Hi Udo,
Very nice setup.
You don't
Sorry, forgot to mention: it's a K3 (serial 59xx) issue here.
Am 11.08.2015 um 13:01 schrieb Udo Langenohl - DK5YA:
Gents,
with the last firmware release I'm struggling with diversity mode. I was
running diversity for a very long time without any issues on my Xpol EME
system (144 MHz). The main
Udo,
the last release where it worked well for you was 5.14?
73 - Petr, OK1RP
-
http://ok1rp.blogspot.com
--
View this message in context:
http://elecraft.365791.n2.nabble.com/Struggling-with-diversity-mod-tp7606199p7606202.html
Sent from the Elecraft mailing list archive at Nabble.com.
Thought of this when replying to an eHam post. Has anyone tried using a
tablet/cell phone screen protector on the Plexiglas screen cover to keep it
from being scratched when hiking or camping? Seems like one tablet screen
protector should give you a few applications if necessary.
73
Greg
I'd back this request too...For me, it's not a particularly high priority, but
would certainly like to see it at some point!
73, Quin G3WRR
- Forwarded Message -
From: Dennis Egan egan.denni...@gmail.com
To: elecraft@mailman.qth.net
Sent: Monday, 10 August 2015, 13:34
Except you may have to clean off the 'sticky goop' from the tape.
I would think sliding the KX3 into an old sock or something similar
would provide adequate protection while transporting it.
73,
Don W3FPR
On 8/11/2015 11:56 AM, Mel Farrer via Elecraft wrote:
Good idea, but I did it a little
yes...and the side panels with folding cover are great too. I was not
referring to transport though...just a little extra protection when operating
in the field (stumps, bouldersetc. :) )
- Original Message -
From: Don Wilhelm w3...@embarqmail.com
To: elecraft@mailman.qth.net
Not trying to promote any ones products, but I would want my buttons and
knobs protected as well and there fore I use a SideKX cover from Gem
products. Great product and a fellow ham
--
View this message in context:
Good idea, but I did it a little different, I covered the screen with clear
shipping tape. A little careful getting all of the air bubbles from forming,
but does a great job protecting the screen of the LCD.. No cost replacing it
either. hi.
Mel, K6KBE
From: a...@cablespeed.com
Sold.
--
View this message in context:
http://elecraft.365791.n2.nabble.com/P3-TX-Monitor-For-Sale-tp7606183p7606209.html
Sent from the Elecraft mailing list archive at Nabble.com.
__
Elecraft mailing list
Home:
Still have my almost loaded K2-100 for sale.Great package of stuff.Please
contact me for more information928-710-9231 kf...@arrl.net 73! Tomy KF7GC
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
Hi,
No compensation is necessary. I have a Ridge Equipment dummy load on one of
my ports and it measures 1.02 with an LP-100A in SWR in bypass mode on 10m.
AB2TC - Knut
Dick Dievendorff-4 wrote
The former.
Dick, K6KR
Sent from my iPhone
On Aug 9, 2015, at 18:17, Jim Miller lt;
I once did a TDR measurement of the distance between the input and
output in bypass mode.
It comes out to be about 18.Interesting, I would have expected
much less.
73 de Brian/K3KO
On 8/11/2015 16:55 PM, ab2tc wrote:
Hi,
No compensation is necessary. I have a Ridge Equipment dummy load
Be aware that most tapes such as shipping tape will generate many thousands
of volts due to ESD effects when the tape is pulled off the surface it is
stuck to.
--Ed, N3CW--
__
Elecraft mailing list
Home:
The late summer/fall Hamfest Season is gearing up. Elecraft will be
attending several Hamfests in the near future and could use some booth help
if anyone is available and willing to put in a few hours. Please reply
directly to l...@elecraft.com
1. Huntsville Hamfest - Aug. 15 and 16 ( sorry
Make sure that you have correctly set the RX states controlled with RX ANT
and ANT.
Sometimes when you upgrade firmware, things like which antenna you were
listening on get lost.
73, Guy K2AV.
On Tue, Aug 11, 2015 at 10:21 AM, ok1rp indi...@xsmail.com wrote:
Udo,
the last release where it
I use this. Better check the size
http://www.bhphotovideo.com/c/product/16160-REG/Domke_722_15R_15x15_Color_Coded_Protective.html
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help:
It will do that if the K3 is in transmit mode but with no power coming
out. The P3 auto-scales the modulation display amplitude, so if there
is no signal it jacks the gain way up and you see quantized noise.
The next version of P3 firmware will limit the maximum gain so you don't
see so much
On 8/11/2015 8:56 PM, KE1B wrote:
Is there any way for the K3S to take its audio from the USB codec
rather than the Line-in or Mic-in?
Exactly the same configuration as AFSK with audio via Line In but
no connection to the Line In jack.
Mode = DATA
SubMode = AFSK A
MENU:Mic Sel
Chris,
I had the same issue with the band down side. With the power off, I just
rapidly and aggressively pushed on the band down side with moderate pressure --
maybe 20 times. The switch seemed to be sticky when new. The issue returns if
the button is partly depressed in haste.
Elecraft
Tonight I turned on my 8-month old K3, and went to switch from 80m to 40m.
Pressing the right side of the BAND rocker switch, the radio began
incorrectly interpreting different commands, and the behavior was
repeatable even after power cycle. First couple of presses changed modes.
Next press
See below
Is there any way for the K3S to take its audio from the USB codec rather than
the Line-in or Mic-in? I don’t see that choice in the menu.
Yes, use LINE IN and don't plug any cable into the LINE IN jack on the
back of the radio. it will then use the USB.
Conversely, is there any
Get Elecraft blessing first, however, a quality electrical contact cleaner with
plastic safe contact lubricant will likely help. Check with Elecraft before
using anything.
Jerry Moore
K3S future owner
On August 11, 2015 8:44:05 PM EDT, Chris Hallinan challi...@gmail.com wrote:
Tonight I turned
There have been problems with the pushbutton switches in the four
controls to the left of the main VFO knob (e.g. speed/mic). Push
the buttons and twiddle the shafts of these controls for two
minutes each, and the problem will probably not recur. When
these controls fail, they cause multiple
Interesting observations after upgrading my K3 to the KSYN3A this evening.
1. I was already running 5.14 firmware. After installation I upgraded
to 5.29 but the DSP was already at 2.83 so I only sent the MCU and FPF
firmware. After the upgrade I started getting ERR DSE. Reflash of all
Search on Google for
LCD Protective Film
Buy a piece large enough and cut to size.
On 8/11/2015 7:48 PM, Richard Donner wrote:
I use this. Better check the size
http://www.bhphotovideo.com/c/product/16160-REG/Domke_722_15R_15x15_Color_Coded_Protective.html
Hi Doug,
If noise is the issue you might want to search the archives. Some
time back a fellow posted information on a replacement Noctua fan that had more
CFM output but was quieter than the original per the specs.
So if replacement is required then possibly the
Is there any way for the K3S to take its audio from the USB codec rather than
the Line-in or Mic-in? I don’t see that choice in the menu.
Conversely, is there any way for N1MM+/MMTTY to send ASCII data to the K3S for
FSK transmission. I don’t think they are set up to do that. What I am trying
On Aug 11, 2015, at 6:17 PM, Joe Subich, W4TV li...@subich.com wrote:
On 8/11/2015 8:56 PM, KE1B wrote:
Is there any way for the K3S to take its audio from the USB codec
rather than the Line-in or Mic-in?
Exactly the same configuration as AFSK with audio via Line In but
no connection
Clever, Dave. Trouble you prepare for seldom
happens, I've heard :-)
Phil W7OX
On 8/11/15 7:33 PM, Dave Hachadorian wrote:
I had a similar problem a couple years ago, and
ordered four
replacement encoder/switches, which are
surprisingly inexpensive.
When I went to actually do the job, it
36 matches
Mail list logo