FWIW Centurylink Webmail email app I have to use has the SEND button next to
the SAVE DRAFT button and I hit
wrong button and SENT before I changed address and deleted all the digest .
Intended this to go to Tom only - but so be it. It was an accident and I
apologize for the whole thing being
I can host if someone will cover domain cost and get family permission to
ressurect from way back. Bandwidth usage currently not issue with hosting
service I use.
N6RNO
On Mon, Jan 11, 2021, 18:52 Joseph Shuman via Elecraft <
elecraft@mailman.qth.net> wrote:
> If you can download the website,
On 1/11/2021 6:29 PM, HP wrote:
Tom - I will give you some unsolicited advice-- The KRC2 was the worst RFI
sucking piece of gear I ever owned.
Simple reason -- it's chock full of Pin One Problems and is unshielded.
Oh, you say, it's a metal chassis. Yes, BUT -- all the connectors are
If you can download the website, or get a copy, it is fairly simple (but
somewhat time consuming to verify the links) to set it up as an archived site
accessible from a DVD or thumb drive. With permission from the family it could
be sold or offered as a resource the same as Fred’s books. No
- On Jan 11, 2021, at 6:31 PM, wrote:
| Send Elecraft mailing list submissions to
| elecraft@mailman.qth.net
| To subscribe or unsubscribe via the World Wide Web, visit
| http://mailman.qth.net/mailman/listinfo/elecraft
| or, via email, send a message with subject or body 'help' to
|
Tom - I will give you some unsolicited advice-- The KRC2 was the worst RFI
sucking piece of gear I ever owned.
I think that being hooked to the guts of the processor in the K3 was a killer
-no amount of fiddling would calm
it down. Was "usable" at 100 watts but my 80 meter antenna runs across
Firmly wiggling the cables (for the 3rd time) resolved the problem.
Something is probably loose inside. Thanks to those who responded for the
suggestions.
73, Ken, K6LA / VY2TT
__
Elecraft mailing list
Home:
You could first check if you get stable connection using the
PX3-utility. If that does not work, it could be an unstable power supply
issue (0,5A ~12V required).
Otherwise I suppose there is a loose connection inside of the P3. You
could check the cable from the main board to the display. The
Could the P3 be in DispTest mode?
Select Menu, the rotate the knob to ;this setting. Needs to be Off for normal
use.
Tom W4KX
From: Ken Widelitz
Sent: Monday, January 11, 2021 5:48 PM
To: Elecraft Support; Elecraft Reflector
Subject: [Elecraft] P3 Issue
P3 stopped working. When turned on, the
P3 stopped working. When turned on, the entire screen flashes from red to
green to blue to blank to grey to checkerboard to grey and then cycles
through those screens again, etc. I have done a reinitialization by holding
down the Label key while turning on the power. Nothing changes.
73, Ken,
Martin,
I have not done it, but the major problem I see is the question of "how
to get the signal inside the enclosure". There is precious little room
on the rear panel. You could go through the right side panel depending
on how you locate the oscillator with respect to the transverter.
Elecrafters,
i have a GPS-controlled LO 116MHz i would like to feed to the XV144 2m
external Transverter. Has anyone done this before ?
Thanks.
--
73!
Martin DM4iM
__
Elecraft mailing list
Home:
I suspect that K2 SN is below 3000. If so, add the Alternate AF Gain
Wiring mod. While you are doing that, I recommend that you replace the
AF Gain control.
The easiest way to change the control is to cut the pins close to the
body, then alternately heat the two mounting tabs while rocking
Hello Yls and Oms.I have a problem with my K2. When turning the AF Audio knob
counterclockwise the speaker is not quiet. Has anybody an idea how to fix this
problem ?Kind regards from germany73Sebo DL7LEVon meinem/meiner Galaxy gesendet
To All...
I am looking to buy a KRC2 if anyone has on in excess to their needs..
Please respond off line to the the listed email address..
Thanks in advance,,,
Tom
N7GP
ex WA8WZG
__
Elecraft mailing list
Home:
Thanks to all for the info. It does appear no critical updates are
required.
73 de Chuck, WS1L
chandler...@gmail.com
On Sun, Jan 10, 2021 at 11:05 AM Don Wilhelm wrote:
> Chuck,
>
> Any K2 above SN 4660 is fully up to date.
> If your real question is about options rather than updates, lift
Sorry, you can only have 1 working at a time. You can use a rs232 a/b switch
to switch between the 2.
Keith, KV5J
Keith
On Sunday, January 3, 2021, 11:33:42 AM CST, Jim Rhodes
wrote:
The question I have is, can I connect the Y-connector to the back of my KPA500
and connect both
17 matches
Mail list logo