was discussed in this thread last year.
http://elecraft.365791.n2.nabble.com/K3-Odd-ALC-behavior-td7633052i20.html
Gordon - N1MGO
On 05/14/2018 03:05 AM, Alan Ibbetson wrote:
Don,
I'm puzzled you when you say
"If it were a K3 problem, that aliasing would also be happening with
other data modes as
it was when
you last transmitted, so if you tune around, click on some signals, have a
listen and then try using TUNE the audio frequency could be anywhere unless
you take specific action.
--
Alan Ibbetson
a...@g3xaq.net
__
Elecraft mai
knows what
Windows does under the covers.
73, Alan G3XAQ
On 5/10/2018 5:58 AM, Alan Ibbetson wrote:
I'm an infrequent user of data modes. I'm trying to use FT8 with the
latest version of the WSJT-X software. Sound card input is via LINE IN.
I'm using DATA A mode.
Everything works OK
,
Don W3FPR
On 5/10/2018 5:58 AM, Alan Ibbetson wrote:
I'm an infrequent user of data modes. I'm trying to use FT8 with the
latest version of the WSJT-X software. Sound card input is via LINE IN.
I'm using DATA A mode.
Everything works OK on transmit except that intermittently the K3 output
falls
sound card/cable(s).
73 Bill AE6JV
On 5/10/18 at 2:58 AM, a...@g3xaq.net (Alan Ibbetson) wrote:
I'm an infrequent user of data modes. I'm trying to use FT8
with the latest version of the WSJT-X software. Sound card
input is via LINE IN. I'm using DATA A mode.
Everything works OK on trans
A software fault? Or something even weirder?
My FW REVS says
uC 05.14
d1 02.83
d2 00.00 (no KRX3 is installed)
FL 01.19
dr 00.00
73. Alan G3XAQ
--
Alan Ibbetson
a...@g3xaq.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailma
KDSP2 DSP option, removed from working K2, complete with standoff
mounting pillar. £100 (one hundred GB pounds) plus postage from England.
Contact alan (at) g3xaq (dot) net.
__
Elecraft mailing list
Home:
efficiency for portable applications (Field Day/DXpedition/travel). Also,
most users would not notice such a subtle change.
73,
Wayne
N6KR
--
Alan Ibbetson
a...@g3xaq.net
__
Elecraft mailing list
Home: http://mailman.qth.net/mailman
Another customer who just did the installation tested transmit close-in phase
noise before/after
and saw pretty dramatic results. At ± 0.5 kHz from the carrier, the new synth
was down about -133 dBc,
while the old was down about -115 dBc.
Does the new synth use the same chip as the KX3? It's
I want to parallel the receivers on my recently-acquired K2 with my K3.
I have the KXV3A RX ANT option on my K3 and K160RX option on my K2. The
obvious way to couple the two is with a 3dB hybrid but that will cost
me 3dB degradation in noise figure on both receivers.
The KRX3 option in the K3
I have just (again) acquired a K2/100. It shows exactly the symptom
below as described in 2009
---
If I move (even very slightly) the rf gain control the audio silences
and the S
meter shows full deflection. After about three seconds or so the receiver
recovers and the s meter returns to
say SN above 4000, the pot should
not be worn out yet unless the operator used it excessively - so in that
case, look for an unsoldered connection between the RF gain control and
the path to the K2 Control Board.
73,
Don W3FPR
On 2/17/2015 12:44 PM, Alan Ibbetson wrote:
I have just (again) acquired
suggest you get the proper one
from Elecraft PN E520004 to be certain it fits.
73,
Don W3FPR
On 2/17/2015 1:15 PM, Alan Ibbetson wrote:
Thanks Don. It's an early K2, serial number 997. Is there
anything unusual about the pot or is it just a standard sized
would Elecraft do it this way, so these gaming headsets don't work
without an ugly crossover adapter? Is there any non-soldering way to
change the connections on the rear panel Mic jack?
Thanks,
Alan G3XAQ
--
Alan Ibbetson
a...@g3xaq.net
put a range of values on
it for the benefit of others who may tread this path with yet another
flavour of not-Yamaha headset.
And now on to fiddling with TX EQ and suchlike. Can you hear me,
Mother?
73, Alan
On 29/10/2013 14:32, Alan Ibbetson wrote:
Hi All,
I'm a new K3 owner so please
I note the astonishingly good numbers for phase noise for the KX3. Which
version of the Si570 LO chip is used? Is it the CMOS one or one of the
more expensive variants?
73, Alan G3XAQ
__
Elecraft mailing list
Home:
I want to increase the output power from my K1 station. I have an
ex-laptop 15V/4A supply to hand so a 3:1 turns ratio collector
transformer looks like it will offer a useful 20W RF output.
As a first step in this exercise I am trying to understand the design of
the K1's own single ended PA
can inject a 4913 kHz signal directly
into the IF amp if you remove the SSB board (or in the W3 jumper
position if the KSB2 is not installed). That may or not be helpful,
but it can give another data point.
73,
Don W3FPR
Alan Ibbetson wrote:
I'm working on K2 S/N 4590 (Rev B pcb
In message [EMAIL PROTECTED], Roelof Bakker
[EMAIL PROTECTED] writes
Hello Alan,
I had also a problem with low output.
It appeared that I had installed a 1800 pF capacitor instead of 180 pF
at C182.
Have you checked this capacitor?
Roelof,
Thanks for your suggestion. C182 is marked 181
removed all the PC polling noise.
Regards,
Alan
In message [EMAIL PROTECTED], Alan Ibbetson
[EMAIL PROTECTED] writes
My newer laptop does not have a serial port and doesn't run DOS so I
got a MicroHAM CW Keyer. It works fine with my FT1000MP Mk5, but with
my K2/100 I get significant noise (like
My newer laptop does not have a serial port and doesn't run DOS so I got
a MicroHAM CW Keyer. It works fine with my FT1000MP Mk5, but with my
K2/100 I get significant noise (like, S5 on the meter) on all bands
whenever the MicroHAM is polling the K2 RS232 for VFO/Mode data.
Has anyone else
21 matches
Mail list logo