On 02/26/2015 11:59 PM, Karlsson Wang wrote:
Do anybody know where it might be possible to find the scaling constants for
a Agiecut AT 200 EDM machine?
I could count and measure myself but lack the correct intruments for accurate
measurements.
Nicklas Karlsson
Do anybody know where it might be possible to find the scaling constants for a
Agiecut AT 200 EDM machine?
I could count and measure myself but lack the correct intruments for accurate
measurements.
Nicklas Karlsson
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 11:44:07 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: [Emc-users] hm2_eth driver missing
I just did a fresh pull and compiled from
Having built multizone ovens and oven controls over the yearsYes, you can
control it with a general purpose machine control program, but the dedicated
temperature controllers you can buy on EBAY or occasionally from www.mpja.com
are very inexpensive and will give you much better control of
You also want to read up on the configuration of the interface\
http://linuxcnc.org/docs/2.7/html/man/man9/hm2_eth.9.html
some more info..
http://wiki.linuxcnc.org/cgi-bin/wiki.pl?Uspace
sam
On 2/26/2015 8:26 AM, Marius Liebenberg wrote:
Thanks Peter, the shebang does it nicely :)
I was
On Thu, Feb 26, 2015, at 09:30 AM, richsh...@comcast.net wrote:
Also keep the safety stuff completely separate from the control stuff. By
that I mean the overtemp limiter controls a mechanical contactor, not just
turns the SSR signal off.
Yep. True story from work a few years ago: We
-- Original Message --
From: Peter C. Wallace p...@mesanet.com
To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine
Controller (EMC) emc-users@lists.sourceforge.net
Sent: 2015-02-26 17:13:54
Subject: Re: [Emc-users] hm2_eth driver missing
On Thu, 26 Feb 2015, Marius
Am I right to say that I cannot run this implementation on Ubuntu 10.04?
I have to move to Debian?
-- Original Message --
From: sam sokolik sa...@empirescreen.com
To: Marius Liebenberg mar...@mastercut.co.za; Enhanced Machine
Controller (EMC) emc-users@lists.sourceforge.net
Sent:
Thanks Peter, the shebang does it nicely :)
I was not aware that I had to have a different flavour to run the
ethernet stuff. If I had done it right from the word go, where would I
have found the information? Or maybe I should ask where would one read
to find out about the different
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 15:04:32 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] hm2_eth driver missing
Am I right to say that I cannot run this
On Thu, 26 Feb 2015, Marius Liebenberg wrote:
Date: Thu, 26 Feb 2015 14:26:06 +
From: Marius Liebenberg mar...@mastercut.co.za
To: Enhanced Machine Controller (EMC) emc-users@lists.sourceforge.net
Subject: Re: [Emc-users] hm2_eth driver missing
Thanks Peter, the shebang does it nicely
I just did a fresh pull and compiled from source. There are no hm2_eth
drivers anywhere that I can find. The firmware for 7i80 is not under the
lib/firmware directory either.
How do I go about to get the complete source to build from?
-
Regards / Groete
Marius D.
I am using the Hostmot 2 drivers but are not at the right computer now, I
could check within a few hurs.
I just did a fresh pull and compiled from source. There are no hm2_eth
drivers anywhere that I can find. The firmware for 7i80 is not under the
lib/firmware directory either.
How do I go
the 7i80 is similar to the 5i25 cards in that the firmware isn't loaded
each time - you have to load the using the mesa-flash utility.
(although it comes with a firmware installed - so you should be able to
test)
As far as the driver not being there - are you running rt-preemt
kernel? My
14 matches
Mail list logo