Re: [Emc-users] TB6600 Stepper Motor Drivers
That's good news. Thanks, Dave On 6/23/2015 12:14 AM, Steve Stallings wrote: > Yes, you can cut the center taps free of each other > and drive it full coil. You might also consider using > half coil depending on how the motor responds. > > All the ones that I have seen are standard connectors > that were hand soldered. Easily modified. > > Steve Stallings > > >> -Original Message- >> From: Dave Cole [mailto:linuxcncro...@gmail.com] >> Sent: Tuesday, June 23, 2015 12:00 AM >> To: emc-users@lists.sourceforge.net >> Subject: Re: [Emc-users] TB6600 Stepper Motor Drivers >> >> Hi Steve, >> >> I did not know that. Thanks for the info.So if I cut the center >> taps loose from pin 5 and insulate the individual center taps >> I should >> have all of the coil end connections in the 5 pin DIN plug and I can >> drive with with a standard bipolar driver? >> >> Unless they glued those DIN connectors together or they are >> molded on, >> that should not be a difficult modification.I don't have >> the machine >> as this is for my nephew. The machine is about 10 years old. Any >> idea if they were molding on the DIN connectors back then? >> >> Thanks, >> >> Dave >> >> On 6/22/2015 10:32 PM, Steve Stallings wrote: >>> Are you aware that the original motors are 6 wire unipolar >>> motors with the center taps connected together at the 5 pin >>> DIN plug? While these motors can be used with a bipolar >>> driver, rewiring will be necessary. >>> >>> Steve Stallings >>> >>> -Original Message- From: Dave Cole [mailto:linuxcncro...@gmail.com] Sent: Monday, June 22, 2015 10:05 PM To: emc-users@lists.sourceforge.net Subject: [Emc-users] TB6600 Stepper Motor Drivers Is anyone on the list using some of the TB6600 stepper >> motor drivers that are listed on Ebay? There are some 5A, 50 volt units that are selling for less than $15 each with free shipping from China or Hong Kong. I need to put together an inexpensive control box for a >> Sherline. The original control box was lost. Dave >>> >> -- >> >>> Monitor 25 network devices or servers for free with OpManager! >>> OpManager is web-based network management software that monitors >>> network devices and physical & virtual servers, alerts via >> email & sms >>> for fault. Monitor 25 devices for free with no restriction. >> Download now >>> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >>> ___ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> --- >> This email has been checked for viruses by Avast antivirus software. >> https://www.avast.com/antivirus >> >> >> -- >> >> Monitor 25 network devices or servers for free with OpManager! >> OpManager is web-based network management software that monitors >> network devices and physical & virtual servers, alerts via >> email & sms >> for fault. Monitor 25 devices for free with no restriction. >> Download now >> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >> ___ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] TB6600 Stepper Motor Drivers
Yes, you can cut the center taps free of each other and drive it full coil. You might also consider using half coil depending on how the motor responds. All the ones that I have seen are standard connectors that were hand soldered. Easily modified. Steve Stallings > -Original Message- > From: Dave Cole [mailto:linuxcncro...@gmail.com] > Sent: Tuesday, June 23, 2015 12:00 AM > To: emc-users@lists.sourceforge.net > Subject: Re: [Emc-users] TB6600 Stepper Motor Drivers > > Hi Steve, > > I did not know that. Thanks for the info.So if I cut the center > taps loose from pin 5 and insulate the individual center taps > I should > have all of the coil end connections in the 5 pin DIN plug and I can > drive with with a standard bipolar driver? > > Unless they glued those DIN connectors together or they are > molded on, > that should not be a difficult modification.I don't have > the machine > as this is for my nephew. The machine is about 10 years old. Any > idea if they were molding on the DIN connectors back then? > > Thanks, > > Dave > > On 6/22/2015 10:32 PM, Steve Stallings wrote: > > Are you aware that the original motors are 6 wire unipolar > > motors with the center taps connected together at the 5 pin > > DIN plug? While these motors can be used with a bipolar > > driver, rewiring will be necessary. > > > > Steve Stallings > > > > > >> -Original Message- > >> From: Dave Cole [mailto:linuxcncro...@gmail.com] > >> Sent: Monday, June 22, 2015 10:05 PM > >> To: emc-users@lists.sourceforge.net > >> Subject: [Emc-users] TB6600 Stepper Motor Drivers > >> > >> Is anyone on the list using some of the TB6600 stepper > motor drivers > >> that are listed on Ebay? > >> > >> There are some 5A, 50 volt units that are selling for less > >> than $15 each > >> with free shipping from China or Hong Kong. > >> > >> I need to put together an inexpensive control box for a > Sherline. The > >> original control box was lost. > >> > >> Dave > >> > >> > > > > > -- > > > Monitor 25 network devices or servers for free with OpManager! > > OpManager is web-based network management software that monitors > > network devices and physical & virtual servers, alerts via > email & sms > > for fault. Monitor 25 devices for free with no restriction. > Download now > > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > > ___ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > > > -- > > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via > email & sms > for fault. Monitor 25 devices for free with no restriction. > Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] TB6600 Stepper Motor Drivers
Hi Steve, I did not know that. Thanks for the info.So if I cut the center taps loose from pin 5 and insulate the individual center taps I should have all of the coil end connections in the 5 pin DIN plug and I can drive with with a standard bipolar driver? Unless they glued those DIN connectors together or they are molded on, that should not be a difficult modification.I don't have the machine as this is for my nephew. The machine is about 10 years old. Any idea if they were molding on the DIN connectors back then? Thanks, Dave On 6/22/2015 10:32 PM, Steve Stallings wrote: > Are you aware that the original motors are 6 wire unipolar > motors with the center taps connected together at the 5 pin > DIN plug? While these motors can be used with a bipolar > driver, rewiring will be necessary. > > Steve Stallings > > >> -Original Message- >> From: Dave Cole [mailto:linuxcncro...@gmail.com] >> Sent: Monday, June 22, 2015 10:05 PM >> To: emc-users@lists.sourceforge.net >> Subject: [Emc-users] TB6600 Stepper Motor Drivers >> >> Is anyone on the list using some of the TB6600 stepper motor drivers >> that are listed on Ebay? >> >> There are some 5A, 50 volt units that are selling for less >> than $15 each >> with free shipping from China or Hong Kong. >> >> I need to put together an inexpensive control box for a Sherline. The >> original control box was lost. >> >> Dave >> >> > > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] TB6600 Stepper Motor Drivers
Are you aware that the original motors are 6 wire unipolar motors with the center taps connected together at the 5 pin DIN plug? While these motors can be used with a bipolar driver, rewiring will be necessary. Steve Stallings > -Original Message- > From: Dave Cole [mailto:linuxcncro...@gmail.com] > Sent: Monday, June 22, 2015 10:05 PM > To: emc-users@lists.sourceforge.net > Subject: [Emc-users] TB6600 Stepper Motor Drivers > > Is anyone on the list using some of the TB6600 stepper motor drivers > that are listed on Ebay? > > There are some 5A, 50 volt units that are selling for less > than $15 each > with free shipping from China or Hong Kong. > > I need to put together an inexpensive control box for a Sherline. The > original control box was lost. > > Dave > > -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] TB6600 Stepper Motor Drivers
Is anyone on the list using some of the TB6600 stepper motor drivers that are listed on Ebay? There are some 5A, 50 volt units that are selling for less than $15 each with free shipping from China or Hong Kong. I need to put together an inexpensive control box for a Sherline. The original control box was lost. Dave --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] fun with logging - mach4 edition
>>I'd be lost without you. :) I know, but its a burden I must carry. ;-) Dave On 6/22/2015 5:54 PM, Peter Homann wrote: > Hey Dave, > > Thanks for looking out for me. I'd be lost without you. :) > > Peter > > On 23/06/2015 12:07 AM, Dave Cole wrote: >> I was referring to Peter Homann, who first made the comment.He is >> well connected to the Mach3/4 world. >> I don't try and stay on top of what is going on in the Mach3/4 world. > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus > > > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] fun with logging - mach4 edition
Hey Dave, Thanks for looking out for me. I'd be lost without you. :) Peter On 23/06/2015 12:07 AM, Dave Cole wrote: > I was referring to Peter Homann, who first made the comment.He is > well connected to the Mach3/4 world. > I don't try and stay on top of what is going on in the Mach3/4 world. --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] Threading wizard problems
I am testing a wizard that Robert Adams is doing for threading with Linuxcnc. There are problems with the Gcode but I am not clued up enough to help. Below is the code that is generated but it does not execute. It runs to G76 and then it just waits there. I think the I and K values are swapped and the I must be negative for outside thread but cannot tell anything more. G18 G90 G7 G21 G94 G97 S828 M3 T3 M6 M8 F401.1 G0 Z2.54 G0 X8.635 G76 P1.25 Z-15 I0.635 J0.2 K1.083 Q0 H0 L2 E1.083 M9 M5 M30 - Regards / Groete Marius D. Liebenberg +27 82 698 3251 +27 12 743 6064 -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] minimum spindle speed
On 22/06/15 18:48, Tom Easterday wrote: > I am controlling a spindle motor with a VFD commanded by modbus. Which VFD? The ones I use have many settings, and adjusting the speed range and acceleration up to speed are all part of them. -- Lester Caine - G8HFL - Contact - http://lsces.co.uk/wiki/?page=contact L.S.Caine Electronic Services - http://lsces.co.uk EnquirySolve - http://enquirysolve.com/ Model Engineers Digital Workshop - http://medw.co.uk Rainbow Digital Media - http://rainbowdigitalmedia.co.uk -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] minimum spindle speed
On 6/22/15 11:48 AM, Tom Easterday wrote: > I am controlling a spindle motor with a VFD commanded by modbus. My current > speed range is 0-3500 rpm. If I run the spindle below 275 rpm the current > spikes and triggers the VFD’s protection shutoff. How do I set the minimum > spindle speed so that the user can’t command a speed below 275rpm? > -Tom There's not a way to limit what values are accepted by G-code S-word commands. You could make a small HAL circuit that prevents commands from being sent to the VFD is the commanded speed is too low. Something like this logic maybe: vfd.enable = motion.spindle-on && (motion.spindle-speed-out > 275) -- Sebastian Kuzminsky -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] minimum spindle speed
Look to see if the VFD has a minimum speed command setting. N. Christopher Perry > On Jun 22, 2015, at 1:48 PM, Tom Easterday wrote: > > I am controlling a spindle motor with a VFD commanded by modbus. My current > speed range is 0-3500 rpm. If I run the spindle below 275 rpm the current > spikes and triggers the VFD’s protection shutoff. How do I set the minimum > spindle speed so that the user can’t command a speed below 275rpm? > -Tom > > > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
[Emc-users] minimum spindle speed
I am controlling a spindle motor with a VFD commanded by modbus. My current speed range is 0-3500 rpm. If I run the spindle below 275 rpm the current spikes and triggers the VFD’s protection shutoff. How do I set the minimum spindle speed so that the user can’t command a speed below 275rpm? -Tom -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
Re: [Emc-users] fun with logging - mach4 edition
You certainly got Brian's attention! Hmmm... no mention of the motion pauses... only accel violations. He is aware that LinuxCNC is open source software right? ;-) He would be way, way ahead to reuse some of the LinuxCNC code which can be done in a legal way and make that plug into Mach4. There has been discussions of a "pluggable" trajectory planner for a long time. I think that is also on the Machinekit TODO list. Siemens is using loads of GPLed software in their proprietary software/hardware products now.Every time I buy a Siemens software/hardware package I get a little CD that has the source code on it for the included GPLed software. Dave On 6/22/2015 10:19 AM, sam sokolik wrote: > https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/messages/148029 > > sam > > On 6/22/2015 9:07 AM, Dave Cole wrote: >> I was referring to Peter Homann, who first made the comment.He is >> well connected to the Mach3/4 world. >> I don't try and stay on top of what is going on in the Mach3/4 world. >> >> Sam did a bunch of testing of Mach3's trajectory planner testing >> previously, so I think his results of the Mach4 testing is very interesting. >> >> It's very cool that LinuxCNC has the ability to observe the performance >> of Mach3/4 by interconnecting the two systems. >> >> That should be a real eye opener for the Mach4 gang. >> >> Dave >> >> On 6/22/2015 2:19 AM, Peter Blodow wrote: >>> I don't. What is it? >>> Peter Blodow >>> >>> Am 22.06.2015 04:14, schrieb Dave Cole: Peter, You should know what is going on Dave On 6/21/2015 8:46 PM, Peter wrote: > > > > > It must be a slow day on the emc-users list. > > Peter > > --- > Peter Homann > http://www.homanndesigns.com/store > > On Mon 22/06/15 9:59 AM , Dave Cole > * wrote:Wow! > > I guess this may be why they were pushing hardware generated step > and > direction creation so hard. > > Dave > > On 6/21/2015 3:28 PM, sam sokolik wrote: > > > https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 > [1] > > > > sam > > > > > -- > > ___ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users [2] > > --- > This email has been checked for viruses by Avast antivirus software. > https://www.avast.com/antivirus [3] > > > -- > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users [4] > > - > Message sent via Atmail Open - http://atmail.org/ > > Links: > -- > [1] > http://webmail.homanndesigns.com/parse.php?redirect=https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 > [2] > http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users > [3] > http://webmail.homanndesigns.com/parse.php?redirect=https://www.avast.com/antivirus > [4] > http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net
Re: [Emc-users] fun with logging - mach4 edition
https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/messages/148029 sam On 6/22/2015 9:07 AM, Dave Cole wrote: > I was referring to Peter Homann, who first made the comment.He is > well connected to the Mach3/4 world. > I don't try and stay on top of what is going on in the Mach3/4 world. > > Sam did a bunch of testing of Mach3's trajectory planner testing > previously, so I think his results of the Mach4 testing is very interesting. > > It's very cool that LinuxCNC has the ability to observe the performance > of Mach3/4 by interconnecting the two systems. > > That should be a real eye opener for the Mach4 gang. > > Dave > > On 6/22/2015 2:19 AM, Peter Blodow wrote: >> I don't. What is it? >> Peter Blodow >> >> Am 22.06.2015 04:14, schrieb Dave Cole: >>> Peter, >>> >>> You should know what is going on >>> >>> Dave >>> >>> On 6/21/2015 8:46 PM, Peter wrote: It must be a slow day on the emc-users list. Peter --- Peter Homann http://www.homanndesigns.com/store On Mon 22/06/15 9:59 AM , Dave Cole * wrote:Wow! I guess this may be why they were pushing hardware generated step and direction creation so hard. Dave On 6/21/2015 3:28 PM, sam sokolik wrote: > https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 [1] > > sam > > -- > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users [2] --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus [3] -- ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users [4] - Message sent via Atmail Open - http://atmail.org/ Links: -- [1] http://webmail.homanndesigns.com/parse.php?redirect=https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 [2] http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users [3] http://webmail.homanndesigns.com/parse.php?redirect=https://www.avast.com/antivirus [4] http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers, alerts via email & sms for fault. Monitor 25 devices for free with no restriction. Download now http://ad.doubleclick.net/ddm/clk/292181274;119417398;o ___ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users >>> --- >>> This email has been checked for viruses by Avast antivirus software. >>> https://www.avast.com/antivirus >>> >>> >>> -- >>> Monitor 25 network devices or servers for free with OpManager! >>> OpManager is web-based network management software that monitors >>> network devices and physical & virtual servers, alerts via email & sms >>> for fault. Monitor 25 devices for free with no restriction. Download now >>> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >>> ___ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >>> >> --- >> Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft. >> https://www.avast.com/antivirus >> >> >> -- >> Monitor 25 network devices or servers for free with OpManager! >> OpManager is web-based network management software that monitors >> network devices and physical & virtual servers, alerts via email & sms >> for fault. Monitor 25 devices for free with no restriction. Download now >> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >> ___ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users > --- > This email has been checked for viruses by Avast antivirus software. > https:
Re: [Emc-users] fun with logging - mach4 edition
I was referring to Peter Homann, who first made the comment.He is well connected to the Mach3/4 world. I don't try and stay on top of what is going on in the Mach3/4 world. Sam did a bunch of testing of Mach3's trajectory planner testing previously, so I think his results of the Mach4 testing is very interesting. It's very cool that LinuxCNC has the ability to observe the performance of Mach3/4 by interconnecting the two systems. That should be a real eye opener for the Mach4 gang. Dave On 6/22/2015 2:19 AM, Peter Blodow wrote: > I don't. What is it? > Peter Blodow > > Am 22.06.2015 04:14, schrieb Dave Cole: >> Peter, >> >> You should know what is going on >> >> Dave >> >> On 6/21/2015 8:46 PM, Peter wrote: >>> >>> >>> >>> >>> It must be a slow day on the emc-users list. >>> >>> Peter >>> >>> --- >>> Peter Homann >>> http://www.homanndesigns.com/store >>> >>> On Mon 22/06/15 9:59 AM , Dave Cole >>> * wrote:Wow! >>> >>> I guess this may be why they were pushing hardware generated step and >>> direction creation so hard. >>> >>> Dave >>> >>> On 6/21/2015 3:28 PM, sam sokolik wrote: >>> > >>> https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 >>> [1] >>> > >>> > sam >>> > >>> > >>> -- >>> > ___ >>> > Emc-users mailing list >>> > Emc-users@lists.sourceforge.net >>> > https://lists.sourceforge.net/lists/listinfo/emc-users [2] >>> >>> --- >>> This email has been checked for viruses by Avast antivirus software. >>> https://www.avast.com/antivirus [3] >>> >>> >>> -- >>> ___ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users [4] >>> >>> - >>> Message sent via Atmail Open - http://atmail.org/ >>> >>> Links: >>> -- >>> [1] >>> http://webmail.homanndesigns.com/parse.php?redirect=https://groups.yahoo.com/neo/groups/mach1mach2cnc/conversations/topics/148006 >>> [2] >>> http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users >>> [3] >>> http://webmail.homanndesigns.com/parse.php?redirect=https://www.avast.com/antivirus >>> [4] >>> http://webmail.homanndesigns.com/parse.php?redirect=https://lists.sourceforge.net/lists/listinfo/emc-users >>> -- >>> Monitor 25 network devices or servers for free with OpManager! >>> OpManager is web-based network management software that monitors >>> network devices and physical & virtual servers, alerts via email & sms >>> for fault. Monitor 25 devices for free with no restriction. Download now >>> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >>> ___ >>> Emc-users mailing list >>> Emc-users@lists.sourceforge.net >>> https://lists.sourceforge.net/lists/listinfo/emc-users >> --- >> This email has been checked for viruses by Avast antivirus software. >> https://www.avast.com/antivirus >> >> >> -- >> Monitor 25 network devices or servers for free with OpManager! >> OpManager is web-based network management software that monitors >> network devices and physical & virtual servers, alerts via email & sms >> for fault. Monitor 25 devices for free with no restriction. Download now >> http://ad.doubleclick.net/ddm/clk/292181274;119417398;o >> ___ >> Emc-users mailing list >> Emc-users@lists.sourceforge.net >> https://lists.sourceforge.net/lists/listinfo/emc-users >> > > --- > Diese E-Mail wurde von Avast Antivirus-Software auf Viren geprüft. > https://www.avast.com/antivirus > > > -- > Monitor 25 network devices or servers for free with OpManager! > OpManager is web-based network management software that monitors > network devices and physical & virtual servers, alerts via email & sms > for fault. Monitor 25 devices for free with no restriction. Download now > http://ad.doubleclick.net/ddm/clk/292181274;119417398;o > ___ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users --- This email has been checked for viruses by Avast antivirus software. https://www.avast.com/antivirus -- Monitor 25 network devices or servers for free with OpManager! OpManager is web-based network management software that monitors network devices and physical & virtual servers
