Thanks Greg for the info. I actually checked out my lilo.conf and it does
reflect what you are mentioning in your answer. This part will be added
to new knowledge.
Thanks again
Richard
At 20:08 2002-10-19 -0400, you wrote:
On Saturday 19 October 2002 05:00
pm, Richard Laframboise wrote:
> but how
Thank you for all the help.
I finally
got it working. The Plextor CD-RW was added after the installation of the
OS and would not be detected properly. Even if installed, afterwards, the
ide-scsi module. Because I am evaluating a solution to protect specific
server configurations, I had no
On Saturday 19 October 2002 05:00 pm, Richard Laframboise wrote:
> but how can I configure my ide cd to be known as a
> scsi device
You need to pass hdx=ide-scsi to your kernel at boot. Different procedure for
LILO and Grub, but you should be able to figure it out by looking at either
/etc/lilo
On Saturday October 19 2002 04:00 pm, Richard Laframboise wrote:
> Thanks Tom for the info but how can I configure my ide cd to be known
> as a scsi device
They have to be, otherwise they wouldn't work at all, even under
windoze ;) There is no such thing as an 'Integrated Drive Electronics/
Thanks Tom for the info but how can I configure my ide cd to be known as
a scsi device
At 15:50 2002-10-19 -0500, you wrote:
On Saturday October 19 2002 02:15
pm, Richard Laframboise wrote:
> Hi List,
>
> I have an IDE
CD burner - Plextor 8/4/32A - How can I
> address it as if it was a S
On Saturday October 19 2002 02:15 pm, Richard Laframboise wrote:
> Hi List,
>
> I have an IDE CD burner - Plextor 8/4/32A - How can I
> address it as if it was a SCSI device ?
>
> Purpose : To make backups
I've got the same burner, it's slave on ide1 (hdd), and ide-scsi
makes
Hi List,
I have an IDE CD burner - Plextor 8/4/32A - How can I address it
as if it was a SCSI device ?
Purpose : To make backups
Thanks
Richard
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakestore.com
I do believe you will find an rpm for mt on your cd. Install it and all will
become magically available.
regards
Daryl
n Tuesday 14 May 2002 14:10, you wrote:
> Hi All,
>
> Following on from my problem with a HP Colorado IDE tape drive, I have
> found the following message in the 'dmesg' outp
Hi All,
Following on from my problem with a HP Colorado IDE tape drive, I have found the
following message in the 'dmesg' output.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: HPModel: COLORADO 14GB Rev: 4.01
Type: Sequential-Access ANSI SCSI r
On Thursday 15 November 2001 06:20 pm, you wrote:
>
> If you find that you need "append=quiet" back into "lilo.conf", I think
> only white space is needed.
What does "quiet" do?
It it still useful to use
ide0=0x1f0
and
floppy=daring
with Mandrake (both are suppose to force the use of faste
-BEGIN PGP SIGNED MESSAGE-
Hash: SHA1
On 15 Nov 2001, Darren King wrote:
Have you added the extra 'space'?
like:
append=" hdc=ide-scsi"
- ^
[]s Ricardo Castanho
>I added a cdrw to my system. I added hdc=ide-scsi to lilo.conf, ran
>lilo and added the alias scsi_adapter ide-scsi
"J. C. Woods" wrote:
>
> Darren King wrote:
> >
> > The problem was that I added hdc=ide-scsi to an existing append line in
> > lilo.conf, it already said append=quiet so I just added a comma and then
> > hdc=ide-scsi. Guess it didn't like that. I added hdc=ide-scsi as the
> > only append item
-BEGIN PGP SIGNED MESSAGE-
Hash: RIPEMD160
You can put the 'quiet' back in, but don't use a comma, like this:
append=" idebus=66 hdc=ide-scsi devfs=mount failsafe"
On Thursday 15 November 2001 14:44, Darren King wrote:
> The problem was that I added hdc=ide-scsi to an existing append l
Darren King wrote:
>
> The problem was that I added hdc=ide-scsi to an existing append line in
> lilo.conf, it already said append=quiet so I just added a comma and then
> hdc=ide-scsi. Guess it didn't like that. I added hdc=ide-scsi as the
> only append item and it worked fine.
>
> Darren
If
On Fri, Nov 16, 2001 at 07:44:45AM +1100, Darren King wrote:
> The problem was that I added hdc=ide-scsi to an existing append line in
> lilo.conf, it already said append=quiet so I just added a comma and then
> hdc=ide-scsi. Guess it didn't like that. I added hdc=ide-scsi as the
> only append i
The problem was that I added hdc=ide-scsi to an existing append line in
lilo.conf, it already said append=quiet so I just added a comma and then
hdc=ide-scsi. Guess it didn't like that. I added hdc=ide-scsi as the
only append item and it worked fine.
Darren
On Thu, 2001-11-15 at 22:34, J. C. W
- Original Message -
From: Darren King <[EMAIL PROTECTED]>
To: <[EMAIL PROTECTED]>
Sent: Thursday, November 15, 2001 12:02 PM
Subject: [expert] ide-scsi question
> I added a cdrw to my system. I added hdc=ide-scsi to lilo.conf, ran
> lilo and added the alias scsi_a
Darren King wrote:
>
> I added a cdrw to my system. I added hdc=ide-scsi to lilo.conf, ran
> lilo and added the alias scsi_adapter ide-scsi to modules.conf.
>
> Now what. cdrecord-scanbus does not see it so I can burn to it yet.
>
> Darren
>
Do a "cat /proc/devices". Do you have a character
I added a cdrw to my system. I added hdc=ide-scsi to lilo.conf, ran
lilo and added the alias scsi_adapter ide-scsi to modules.conf.
Now what. cdrecord-scanbus does not see it so I can burn to it yet.
Darren
Want to buy your Pack or Services from MandrakeSoft?
Go to http://www.mandrakest
I've set up my kernel with ide-scsi, so that I can use my ATAPI CD drive for
digital audio extraction with cdrdao, which works fine. However, I cannot play
the audio CDs that I'm extracting from!
I've tried kscd and ascd, but neither work.
My ATAPI drive is /dev/hdd. With emulation, it shows up
Mage Grimau wrote:
>
> I was using ide-scsi to use my cd burner under 7.1 just fine.
> I added a real scsi (adaptec) card and HD.
> Now cdrecord -scanbus just sees the real scsi and not my cd burner.
> Can they work together, or do I have to remove the real scsi to use
> my cd burner?
>
> --
> M
Hi,
I don't think so. I'm using a Future Domain Scsi card with a scsi cd
burner. Also, I have configured my cdrom ide as scsi with the ide-scsi
option.
If I run cdrecord -scanbus the result is:
Cdrecord 1.9 (i586-mandrake-linux-gnu) Copyright (C) 1995-2000 Jörg
Schilling
Linux sg driver version:
I was using ide-scsi to use my cd burner under 7.1 just fine.
I added a real scsi (adaptec) card and HD.
Now cdrecord -scanbus just sees the real scsi and not my cd burner.
Can they work together, or do I have to remove the real scsi to use
my cd burner?
--
Mage Grimau
..
Shouldn't need to insmod or modprobe at all.
Most likely,
a) the IDE devices should stop moving once you get rid of the insmod.
b) the SCSI devices all got bumped up one in the chain.
On Sun, 02 Apr 2000, you wrote:
| A friend told me to enable my IDE CD-writer by putting append="hdc=ide-scsi"
On Mon, 03 Apr 2000, you wrote:
>
> /dev/sr0 is another location where your cdwriter appears.
>
> insmod is not the currently preferred method
>
You're correct on that. My bad. :-)
John
John Aldrich wrote:
>
> On Sun, 02 Apr 2000, you wrote:
> > A friend told me to enable my IDE CD-writer by putting append="hdc=ide-scsi" in
> > lilo.conf (lilo was run afterward) and insmod ide-scsi in rc.local.
> >
> > That allowed xcdroaster to have access to my CD-writer as scd0, but now I can
Bug Hunter wrote:
> What is happening here is that the scsi emulator for IDE is being
> loaded, and possibly it is blowing away your other scsi devices (The scsi
> emulator for Parallel Port, and the scsi scanner).
>
> I suspect a rmmod ide-scsi will allow you to use those devices.
>
> Note
What is happening here is that the scsi emulator for IDE is being
loaded, and possibly it is blowing away your other scsi devices (The scsi
emulator for Parallel Port, and the scsi scanner).
I suspect a rmmod ide-scsi will allow you to use those devices.
Note that with the ide-scsi module
Well I think that the problem is that you have reordered the ID devices, so your
link files are wrong because they point to the wrong devices.
If you do a:
cat /proc/scsi/scsi
you will have the devices that are ok.
But the question is change in the dev directory the link files that you have.
T
On Sun, 02 Apr 2000, you wrote:
> A friend told me to enable my IDE CD-writer by putting append="hdc=ide-scsi" in
> lilo.conf (lilo was run afterward) and insmod ide-scsi in rc.local.
>
> That allowed xcdroaster to have access to my CD-writer as scd0, but now I can't
> read from my IDE Zip drive
A friend told me to enable my IDE CD-writer by putting append="hdc=ide-scsi" in
lilo.conf (lilo was run afterward) and insmod ide-scsi in rc.local.
That allowed xcdroaster to have access to my CD-writer as scd0, but now I can't
read from my IDE Zip drive or scan with my SCSI scanner. I presume th
31 matches
Mail list logo
