hello,
so, any tips for measuring distance in PCBNEW ?
I tried to make an auxilliary axis in order to place my (0,0) to a corner of my
pcb, but it is only used for drilling etc..
any ideas ?
12:46:11 -
Julien Bayle julien.ba...@gmail.com julien.bayle%40gmail.com wrote:
hello,
so, any tips for measuring distance in PCBNEW ?
I tried to make an auxilliary axis in order to place my (0,0) to a corner
of my pcb, but it is only used for drilling etc..
any ideas
specify that.
I route by hand so in Kicad, I specify it in DRC Control dialog (PCB Design
Rules Check)
M.
On Thu, May 21, 2009 at 3:27 PM , Julien Bayle wrote:
thanks a lot.
where can I do that?
before exporting the dsn file? inside the router?
2009/5/21 kajdas *kaj...@cox.net* kaj
sure you spacings are correct.
M.
On Fri, May 22, 2009 at 7:53 AM , Julien Bayle wrote:
could you help me with that?
I looked for that ... I didn't find anything in kicad.. only the drc
test...
but I don't find the rules... and how I could change and tweak them
:-(
Julien
if you intend to autoroute boards.
Best Regards,
Brian Sidebotham.
2009/5/17 Julien Bayle julien.ba...@...:
[Attachment(s) from Julien Bayle included below]
hi Brian,
here is the error message (in french, but I can translate it)
here is the ses file from freerouting.net
hello,
I'm using freerouting.net to autoroute my pcbs for the protodeck project I
began.
at the beginning, I created my modules but I did a mistake:
I put pads for leds, for switchs and for headers on the two side!
But I only want to solder on one side (bottom side for leds + switches
upper
it will help, one day :)
--- In kicad-users@yahoogroups.com, Julien Bayle julien.ba...@... wrote:
hello,
I'm using freerouting.net to autoroute my pcbs for the protodeck project I
began.
at the beginning, I created my modules but I did a mistake:
I put pads for leds, for switchs
sides.
On one side, the pad size could be almost zero but the hole is still there
and needs to be accounted for when routing.
Otherwise it is a surface mount part and the router does what it did for
you the first time.
Martin
On Thu, May 21, 2009 at 10:13 AM , Julien Bayle wrote:
I think I
??
--- In kicad-users@yahoogroups.com, Julien Bayle julien.ba...@... wrote:
thanks kajds for your answer.
a friend advised me to keep the same pad size on both side... in order to
make it easier to design.
I guess it is ok too :)
Julien
2009/5/21 kajdas kaj...@...
Of course it makes
I found another way (but it is a tip...)
I create zone around holes
I fill them
and I uncheck the Parameterrouteignore conduction aeras
it works..
But I guess your advice is THE solution, not my tip...
--- In kicad-users@yahoogroups.com, Julien Bayle julien.ba...@... wrote:
thanks a lot
:
--- In kicad-users@yahoogroups.com, Julien Bayle julien.bayle@ wrote:
hi,
I create a pretty ground zone in order to suppress some tracks.
no problem for the zone creation. it is very well documented so..
BUT I have a little problem:
after the filling of the zone, it remains all
,
Brian Sidebotham.
2009/5/17 Julien Bayle julien.ba...@...:
[Attachment(s) from Julien Bayle included below]
hi Brian,
here is the error message (in french, but I can translate it)
here is the ses file from freerouting.net, too.
I hope I can solve that ...
as I
hi,
I create a pretty ground zone in order to suppress some tracks.
no problem for the zone creation. it is very well documented so..
BUT I have a little problem:
after the filling of the zone, it remains all the tracks existing between
the pads supposed to be connected to the zone.
I put a
the real question is :
what is the differnce between soldcomp maskcomp ???
--- In kicad-users@yahoogroups.com, Julien Bayle julien.ba...@... wrote:
hi all experts,
I'm inside a big project: http://www.julienbayle.net/diy/protodeck/
I finished one of the PCBs it requires and I'm very
.
the real question is :
what is the differnce between soldcomp maskcomp ???
--- In kicad-users@yahoogroups.com, Julien Bayle wrote:
hi all experts,
I'm inside a big project:
http://www.julienbayle.net/diy/protodeck/
I finished one of the PCBs
hi,
I would want to autoroute my pcb.
I tested native autorouter... on several pcb, it began to autoroute and
finished . on some other, it didn't start and just displayed the whole unrouted
wires.
so, I tested freerouting.net
it works everytime and it is pretty good!
BUT, how to use the result
but ...
Julien
2009/5/17 Brian Sidebotham brian.sidebot...@gmail.com
2009/5/17 Julien Bayle julien.ba...@gmail.com julien.bayle%40gmail.com
:
hi,
I would want to autoroute my pcb.
I tested native autorouter... on several pcb, it began to autoroute and
finished . on some other, it didn't start
Hello,
I'm working on a big project: the protodeck midibox based controller.
All will be shared here: http://www.julienbayle.net/diy/protodeck/ and for the
moment, you can check different step here:
http://www.julienbayle.net/diy/protodeck/blog/
So, the question is:
I created some modules
18 matches
Mail list logo
