Mauro,
Please pulll changes:
1. correct init values in cnt_storage for TS continuity check:
http://udev.netup.ru/cgi-bin/hgwebdir.cgi/v4l-dvb-aospan/rev/f753dd0f27c9
2. Show speed of transport stream in Kbit/sec:
http://udev.netup.ru/cgi-bin/hgwebdir.cgi/v4l-dvb-aospan/rev/91923e3471ac
for
Hello Igor ,
I want to thank you for making those patches available . I have been
able to patch the latest HG pull and to compile and install the drivers
. I decided to install the whole lot as it was a bit hard to workout
just the ko's responsible for the S350 . After installing the card I
On 27 June 2009 12:09:20 OM Ugarcina wrote:
Hello Igor ,
I want to thank you for making those patches available . I have been
able to patch the latest HG pull and to compile and install the drivers
. I decided to install the whole lot as it was a bit hard to workout
just the ko's responsible
On Saturday 27 June 2009 00:04:45 m-kariche...@ti.com wrote:
From: Muralidharan Karicheri m-kariche...@ti.com
Re-sending adding Hans to CC
Following updates to vpfe capture driver :-
1) Adding support for camera capture using mt9t031 driver
(A patch for mt9t031 is already
On Saturday 27 June 2009 00:05:10 m-kariche...@ti.com wrote:
From: Muralidharan Karicheri m-kariche...@ti.com
Following updates to ccdc driver :-
1) Adding support for camera capture using mt9t031
2) Changed default resolution for ycbcr capture to NTSC to match
with
On Saturday 27 June 2009 00:05:48 m-kariche...@ti.com wrote:
From: Muralidharan Karicheri m-kariche...@ti.com
Following are the changes:-
1) moved i2c board specific part to sub device configuration
structure so that sub device can be loaded from vpfe capture
using the new
On Friday 26 June 2009 16:43:52 Aguirre Rodriguez, Sergio Alberto wrote:
But in user space there is nothing changed having access to
device and control them.
As you know, subdev and int-device is all about how to bind
interface(or host?) and device and make them communicated each
I found a problem with w_scan. With the following system
(2x HVR-4000):
/dev/dvb/adapter0/frontend0 : DVB-S/S2
/dev/dvb/adapter0/frontend1 : DVB-T
/dev/dvb/adapter1/frontend0 : DVB-S/S2
/dev/dvb/adapter1/frontend1 : DVB-T
there is no way to do a (DVB-T) scan on adapter1/frontend1 because
1)the
--- a/arch/arm/mach-davinci/board-dm355-evm.c
+++ b/arch/arm/mach-davinci/board-dm355-evm.c
@@ -136,10 +136,66 @@ static void dm355evm_mmcsd_gpios(unsigned gpio)
dm355evm_mmc_gpios = gpio;
}
-static struct tvp514x_platform_data tvp5146_pdata = {
- .clk_polarity = 0,
This message is generated daily by a cron job that builds v4l-dvb for
the kernels and architectures in the list below.
Results of the daily build of v4l-dvb:
date:Sat Jun 27 19:00:02 CEST 2009
path:http://www.linuxtv.org/hg/v4l-dvb
changeset: 12133:05e6c5c9bcb4
gcc version: gcc
Hi Antti... no idea... I think I saw similar errors when the reset GPIO
of the tuner was not on the correct position in some cards... but I'm
not sure. Frankly with this card I doubt it never worked, since it was
only confirmed by one person... so perhaps that GPIO missplacement is
possible or
On Sat, Jun 27, 2009 at 12:25 AM, George Adamsg_adam...@hotmail.com wrote:
Thanks again to both of you for your help. I gave the no_poweroff flag a
try, but didn't see any difference. I also tried a setchannel 3 during the
middle of the encoding session, and also saw no change.
But I
On Sat, 2009-06-27 at 17:57 -0400, Robert Krakora wrote:
Andy:
I too care about the environment. I am trying to find some extra time
to figure out if my KWorld 330U USB TV devices are actually going into
low power mode or not. I would say not as they get really hot, so I
unplug them when
On Sat, Jun 27, 2009 at 8:17 PM, Andy Wallsawa...@radix.net wrote:
Oh, I'm not against power management. But state is lost - somethings
that's fixable with a lot of work apparently. I was thinking maybe the
V4L2 spec could change.
I was also pondering maybe the final close() shouldn't be
Hi,
Am Samstag, den 27.06.2009, 00:25 -0400 schrieb George Adams:
Thanks again to both of you for your help. I gave the no_poweroff flag a
try, but didn't see any difference. I also tried a setchannel 3 during the
middle of the encoding session, and also saw no change.
hm, I'm late on the
A final wrapup (and again, thanks all of you - I'm indebted to you for your
help):
after booting:
v4l2-ctl -F
Frequency: 9076 (567.25 MHz)
ivtv-tune -c 3
/dev/video0: 61.250 MHz
v4l2-ctl -F
Frequency: 980 (61.25 MHz)
v4l2-ctl -f 61.25
Frequency set to 980 (61.25 MHz)
Hi,
Am Samstag, den 27.06.2009, 22:36 -0400 schrieb George Adams:
A final wrapup (and again, thanks all of you - I'm indebted to you for your
help):
after booting:
v4l2-ctl -F
Frequency: 9076 (567.25 MHz)
ivtv-tune -c 3
/dev/video0: 61.250 MHz
v4l2-ctl -F
Frequency: 980
17 matches
Mail list logo
