As I recall, there wasn’t anything “official”, but if a car came in under
warranty or close to it with the symptoms, it got replaced.
My former 350SDL got either a crate engine or short block, I couldn’t quite
tell exactly which from the VMI, around 90k.
-D
On Feb 13, 2024, at 12:03 PM,
IIRC, there was a factory recall on the rodbenders to address this problem.
On Tue, Feb 13, 2024 at 12:41 PM dan penoff.com via Mercedes <
mercedes@okiebenz.com> wrote:
> 300SDL version was prone to water jacket leaks in the head/head gasket, as
> I recall. There were later heads (014?) that
300SDL version was prone to water jacket leaks in the head/head gasket, as I
recall. There were later heads (014?) that were redesigned to address the
issue. 350SDLs had leakage problems as well that when extreme, would cause the
#1 cylinder (typically) to hydrolock, causing the connecting rod
On 13/02/2024 11:33 AM, dan penoff.com via Mercedes wrote:
I thought they were the same engine but the 350SDL had 210 ci versus 183 ci for
the 300SDL? I believe the displacement difference would have been a change in
both bore and stroke.
Different heads, too, as I recall.
-D
Did they
I thought they were the same engine but the 350SDL had 210 ci versus 183 ci for
the 300SDL? I believe the displacement difference would have been a change in
both bore and stroke.
Different heads, too, as I recall.
-D
> On Feb 13, 2024, at 9:28 AM, Allan Streib via Mercedes
> wrote:
>
>
The 350 SDL became known as the rodbender, I believe they started badging them
300SDL at some point to get away from that reputation. At least I recall
hearing that.
On Tue, Feb 13, 2024, at 11:24, Andrew Strasfogel via Mercedes wrote:
> Focus on what's important, please.
>
> On Tue, Feb 13,
Focus on what's important, please.
On Tue, Feb 13, 2024 at 8:06 AM Bob Rentfro via Mercedes <
mercedes@okiebenz.com> wrote:
> They are. I wasn’t paying good attention in the initial post.
>
> AZBob
>
> Sent from my iPhone
>
> > On Feb 12, 2024, at 9:37 PM, Andrew Strasfogel via Mercedes <
>
They are. I wasn’t paying good attention in the initial post.
AZBob
Sent from my iPhone
> On Feb 12, 2024, at 9:37 PM, Andrew Strasfogel via Mercedes
> wrote:
>
> I was taught that the 350SDLs were the rod benders.
>
>> On Mon, Feb 12, 2024 at 11:26 PM Andrew Strasfogel
>> wrote:
>>
>>
I was taught that the 350SDLs were the rod benders.
On Mon, Feb 12, 2024 at 11:26 PM Andrew Strasfogel
wrote:
> Add the labor cost to R/R and it gets a little pricey.
>
> On Mon, Feb 12, 2024 at 11:19 PM Allan Streib wrote:
>
>> OM617s have got to be a dime a dozen. I have one I'd sell cheap.
Add the labor cost to R/R and it gets a little pricey.
On Mon, Feb 12, 2024 at 11:19 PM Allan Streib wrote:
> OM617s have got to be a dime a dozen. I have one I'd sell cheap.
>
> On Mon, Feb 12, 2024, at 23:15, Andrew Strasfogel wrote:
>
> Could have lost its oil and fried the engine. I bought
OM617s have got to be a dime a dozen. I have one I'd sell cheap.
On Mon, Feb 12, 2024, at 23:15, Andrew Strasfogel wrote:
> Could have lost its oil and fried the engine. I bought an '83 300TD like
> this. Turned over but wouldn't start.
>
> On Mon, Feb 12, 2024 at 10:40 PM Allan Streib via
Could have lost its oil and fried the engine. I bought an '83 300TD like
this. Turned over but wouldn't start.
On Mon, Feb 12, 2024 at 10:40 PM Allan Streib via Mercedes <
mercedes@okiebenz.com> wrote:
> "Doesn’t start" I was gonna say offer $500 and work up from there but the
> interior does
"Doesn’t start" I was gonna say offer $500 and work up from there but the
interior does look to be in pretty nice shape especially for closing in on a
quarter-million miles and it's an interesting color.
On Mon, Feb 12, 2024, at 17:46, Floyd Thursby via Mercedes wrote:
> Offer $1500, probably
I’m trying to engage the seller to ask him what he means by “will not start”.
Plus, if it’s still registered or will there be Mucho fees to get it out of the
PRK. We will see what he says.
AZBob
Sent from my iPhone
> On Feb 12, 2024, at 6:53 PM, Bob Rentfro wrote:
>
> Yeah, I didn’t look
Yeah, I didn’t look or read very closely because when I posted that I thought
it was an SDL.
My nuclear attention to detail is waning now that I’ve been retired for a
minute.
I’d check that out if I were closer.
AZBob
Sent from my iPhone
> On Feb 12, 2024, at 4:45 PM, Kaleb Striplin via
603 90-95
Sent from my iPhone
> On Feb 12, 2024, at 5:41 PM, Dwight Giles via Mercedes
> wrote:
>
> which is the rodbender?
>
>> On Mon, Feb 12, 2024, 6:01 PM Andrew Strasfogel via Mercedes <
>> mercedes@okiebenz.com> wrote:
>>
>> No. This is the million mile engine. Only Arnold can bend
Isn't it the 6 cylinder in the SDL?
Randy
On 12/02/2024 5:40 PM, Dwight Giles via Mercedes wrote:
which is the rodbender?
On Mon, Feb 12, 2024, 6:01 PM Andrew Strasfogel via Mercedes <
mercedes@okiebenz.com> wrote:
No. This is the million mile engine. Only Arnold can bend the rods.
On Mon,
which is the rodbender?
On Mon, Feb 12, 2024, 6:01 PM Andrew Strasfogel via Mercedes <
mercedes@okiebenz.com> wrote:
> No. This is the million mile engine. Only Arnold can bend the rods.
>
> On Mon, Feb 12, 2024, 5:19 PM Kaleb Striplin via Mercedes <
> mercedes@okiebenz.com> wrote:
>
> > 617.
Offer $1500, probably needs fuel filters. It looks really nice
--FT
On 2/12/24 5:18 PM, Kaleb Striplin via Mercedes wrote:
617. Looks like a good deal.
Sent from my iPhone
On Feb 12, 2024, at 4:02 PM, Robert Rentfro via Mercedes
wrote:
No. This is the million mile engine. Only Arnold can bend the rods.
On Mon, Feb 12, 2024, 5:19 PM Kaleb Striplin via Mercedes <
mercedes@okiebenz.com> wrote:
> 617. Looks like a good deal.
>
> Sent from my iPhone
>
> On Feb 12, 2024, at 4:02 PM, Robert Rentfro via Mercedes <
>
617. Looks like a good deal. Sent from my iPhoneOn Feb 12, 2024, at 4:02 PM, Robert Rentfro via Mercedes wrote:https://www.facebook.com/marketplace/item/1383555115882058/ Nice color. AZBob Sent from Mail for Windows
___http://www.okiebenz.comTo search list
https://www.facebook.com/marketplace/item/1383555115882058/ Nice color. AZBob Sent from Mail for Windows
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
So with 269000 miles does that mean the engine has outgrown its Rod bending
phase?
On Mon, May 3, 2021, 9:35 PM Buggered Benzmail via Mercedes <
mercedes@okiebenz.com> wrote:
> Doesn’t look bad aside from being white
>
> --FT
> Sent from iPhone
>
> > On May 3, 2021, at 8:53 PM, Allan Streib via
Doesn’t look bad aside from being white
--FT
Sent from iPhone
> On May 3, 2021, at 8:53 PM, Allan Streib via Mercedes
> wrote:
>
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery
Could be a good deal.
Sent from my iPhone
> On May 3, 2021, at 7:53 PM, Allan Streib via Mercedes
> wrote:
>
>
> https://louisville.craigslist.org/cto/d/louisville-sd-mercedes-diesel/7316406828.html
>
> Allan
>
> ___
> http://www.okiebenz.com
>
> To
https://louisville.craigslist.org/cto/d/louisville-sd-mercedes-diesel/7316406828.html
Allan
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
Not mine, etc, etc.
http://lansing.craigslist.org/cto/5389237120.html
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
Well, looks good in the photos.
Wilton
- Original Message -
From: "Mitch Haley via Mercedes" <mercedes@okiebenz.com>
To: "Mercedes List" <mercedes@okiebenz.com>
Cc: "Mitch Haley" <mi...@mitchellhaley.com>
Sent: Sunday, January
e - From: "Mitch Haley via Mercedes"
> <mercedes@okiebenz.com>
> To: "Mercedes List" <mercedes@okiebenz.com>
> Cc: "Mitch Haley" <mi...@mitchellhaley.com>
> Sent: Sunday, January 10, 2016 1:38 PM
> Subject: [MBZ] Rodb
Diesel badge and star missing from trunk lid, no dealer striping on
sides, side moldings s'posed to be grey - they seem to have a beige
tint - car may have been repainted.
Wilt
Maybe paint sprayed over duct tape to cover rust. "Southern" might
mean Battle Creek or Benton Harbor. Hard to
;
To: "Mercedes Discussion List" <mercedes@okiebenz.com>
Cc: "Kaleb C. Striplin" <ka...@striplin.net>
Sent: Sunday, January 10, 2016 2:22 PM
Subject: Re: [MBZ] Rodbender in MI
It does but there is something funny about it, something with the side
moulding.
Sent from my
Not mine, etc, etc.
http://lansing.craigslist.org/cto/5389237120.html
Nice color too! At least it is not black, or almost as bad, white.
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change
sorry, don't have a link. just a pitcher.
Musta been a bad day. or a bad month
-- next part --
A non-text attachment was scrubbed...
Name: Rodbender.jpg
Type: application/octet-stream
Size: 45537 bytes
Desc: not available
URL:
http://www.benzworld.org/forums/w140-s-class/2182777-1992-300sd-sale.html#post10443393
Just curious
Dan
___
http://www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
via Mercedes mercedes@okiebenz.com
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Monday, October 27, 2014 5:49 PM
Subject: [MBZ] Rodbender?
http://www.benzworld.org/forums/w140-s-class/2182777-1992-300sd-sale.html#post10443393
Just curious
Dan
Yes, same as '90 '91, unless it's had a proper crate engine replacement.
BTW, notice MB's deceptive practice - calling a 350 rodbender a
300 trying to make buyers think they were getting one of the
more-solid 300's from years earlier?
Wilton
I'd guess that was the stuffed shirts in MBUSA.
So where's the risk? It's lasted 132 k miles and if it runs properly now,
the odds are it will keep on running for a long time w/o major problems.
On Mon, Oct 27, 2014 at 6:28 PM, Curly McLain via Mercedes
mercedes@okiebenz.com wrote:
Yes, same as '90 '91, unless it's had a proper crate
In the local classifieds:
1991 Mercedes Benz 350 SDL Large sedan, 6 cyl. Diesel.
Excellent. 108,000 orig. miles. 25 mpg. Sun roof and full
luxuries. Smoke Silver. $9000. 812-824-9131
Not mine, etc.
Allan
--
1983 300D
1979 300SD
___
http://www.okiebenz.com
On Sat, Aug 20, 2011 at 8:06 PM, Allan Streib str...@cs.indiana.edu wrote:
In the local classifieds:
1991 Mercedes Benz 350 SDL Large sedan, 6 cyl. Diesel.
Excellent. 108,000 orig. miles. 25 mpg. Sun roof and full
luxuries. Smoke Silver. $9000. 812-824-9131
Not totally out of line for an
Rich wrote: Uh-oh, here we go.
Don't worry, they sold the car.
Donald H. Snook
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
My Factory Crated new zero time engine arrived with a blank spot and I
watched the dealer stamp the original serial number on it. So other than all
the 'Factory and Dealer paperwork and Records' I fail to see how you can tell
which engine is in the car.
Now maybe if the engine was replaced
@ okiebenz .com
Sent: Friday, February 5, 2010 9:55:56 AM GMT -05:00 US/Canada Eastern
Subject: [ MBZ ] Rodbender question
My Factory Crated new zero time engine arrived with a blank spot and I
watched the dealer stamp the original serial number on it. So other than all
the 'Factory and Dealer
, etc.
Wilton
- Original Message -
From: pm7...@comcast.net
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Friday, February 05, 2010 10:16 AM
Subject: Re: [MBZ] Rodbender question
So much for 'Numbers Matching' at a Benz Auction.
My other car is a 1954 Nash Metropolitan, I
YES! My memory isn't that far gone afterall! Thanks for corroborating what I
thought I remembered.
On Fri, Feb 5, 2010 at 8:55 AM, W140 w...@juno.com wrote:
My Factory Crated new zero time engine arrived with a blank spot and I
watched the dealer stamp the original serial number on it. So
Is there a way to know if a rodbender has had the engine replaced? Is
there a casting number or some other indicator that would indicate it
has been done?
Donald H Snook
McDonald Tinker Law Firm
(316) 263-5851
www.mtsqh.com
___
http://www.okiebenz.com
For
, February 4, 2010 1:00:12 PM GMT -05:00 US/Canada Eastern
Subject: [MBZ] Rodbender question
Is there a way to know if a rodbender has had the engine replaced? Is
there a casting number or some other indicator that would indicate it
has been done?
Donald H Snook
McDonald Tinker Law Firm
Take the VIN at the dealer to pull a service history? Supposedly the
good engines are factory rebuilds, I'd assume most of these were
installed by dealerships.
Allan
On Thu, 04 Feb 2010 12:00 -0600, Donald Snook dsn...@mtsqh.com wrote:
Is there a way to know if a rodbender has had the engine
Uh-oh, here we go.
--R
Donald Snook wrote:
Is there a way to know if a rodbender has had the engine replaced? Is
there a casting number or some other indicator that would indicate it
has been done?
Donald H Snook
McDonald Tinker Law Firm
(316) 263-5851
www.mtsqh.com
Dealer receipt for replacement engine in THAT car? MB records by VIN?
Wilton
- Original Message -
From: Donald Snook dsn...@mtsqh.com
To: Mercedes Mercedes@okiebenz.com
Sent: Thursday, February 04, 2010 1:00 PM
Subject: [MBZ] Rodbender question
Is there a way to know if a rodbender
(not a rebuild) will have a
blank spot with no number.
-Max
-Original Message-
From: mercedes-boun...@okiebenz.com
[mailto:mercedes-boun...@okiebenz.com] On Behalf Of Donald Snook
Sent: Thursday, February 04, 2010 1:00 PM
To: Mercedes
Subject: [MBZ] Rodbender question
Is there a way
Just ask Kaleb. He has had most of them in his back yard for a while.
Randy
-Original Message-
From: mercedes-boun...@okiebenz.com
[mailto:mercedes-boun...@okiebenz.com]on Behalf Of Donald Snook
Sent: Thursday, February 04, 2010 12:00 PM
To: Mercedes
Subject: [MBZ] Rodbender question
I go with 'ask the dealer'.
Serial numbers not matching does not mean the current engine in the car escapes
rodbender status. It could have come from a salvage vehicle, or worse yet, have
been rebuilt by incompetents.
Mitch.
___
http://www.okiebenz.com
hahahahahahahahahahahahahahahahahahaha
pm7...@comcast.net wrote:
Bring VIN# to dealer. He can tell you the engine S/N installed at factory.
Why would you care? Even the bad ones are good for a few weeks
No
I bought a factory engine for the '76 300D once - they were on sale,
supposedly one of the last two in the Chicago warehouse. It had a blank spot
where the serial number was supposed to be. I heard somewhere that a dealer
was supposed to stamp the original engines number there. Can't verify that
2-tone paint?
--R
92 Mercedes 300SD - $3500 (Summerville)
Date: 2010-01-20, 2:40PM EST
Reply to: sale-9awbt-1562129...@craigslist.org
Wrong year?
Wilton
- Original Message -
From: Rich Thomas richthomas79td...@constructivity.net
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Wednesday, January 20, 2010 5:20 PM
Subject: [MBZ] Rodbender?
2-tone paint?
--R
92 Mercedes 300SD - $3500 (Summerville
Found out a bit more about this... all evidence is that the engine is original.
Dealer services records show a lot of scheduled maintenance was performed but
no engine problems are documented so far.
Thought I'd pass this along... I don't want to part with $4,900 right now.
On Tue, 05 Jan
Hi All
Happy New Year
My knowledge, and experience, of MB's is fairly limited - can someone
explain what a 'Rodbender' is ?
I've seen the term used often on here, and I know it's re: a particular
engine - someone educate me further !
Howard
Bath
England
'93 1.8 190E 5-speed manual,
Howard wrote: My knowledge, and experience, of MB's is fairly limited - can
someone
explain what a 'Rodbender' is ? I've seen the term used often on here, and I
know it's re: a particular
engine - someone educate me further!
I don't know if someone else has already answered this but, the term
On Wed, 06 Jan 2010 08:13 -0600, Donald Snook dsn...@mtsqh.com wrote:
Regardless of its nomenclature, the 3.5 diesel engine is the rodbender - even
if the
car is called a 300SD in the 140 Chassis. Don't get that confused with
the 126 300SD. That was a fantastic engine and a great car.
'90 350SD/SDL (126) also rodbender.
Wilton
- Original Message -
From: Donald Snook dsn...@mtsqh.com
To: Mercedes@okiebenz.com
Sent: Wednesday, January 06, 2010 9:13 AM
Subject: Re: [MBZ] Rodbender ?
Howard wrote: My knowledge, and experience, of MB's is fairly limited -
can someone
Donald
Thanks for that clear explanation !
Howard Fulford
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To Unsubscribe or change delivery options go to:
Rod bender refers to the later OM603.xx engine used in the 1990-95
diesel w126 and w140 of the SD class. The rods would fail and lead to
ovaling of cylinders.
clay
On Jan 6, 2010, at 12:59 AM, Howard Fulford wrote:
Hi All
Happy New Year
My knowledge, and experience, of MB's is fairly
Thats good to know, because thats probably what I am going to end up
doing. Wonder how much wear that guy had on the #1 cylinder walls.
Donald Snook wrote:
Howard wrote: My knowledge, and experience, of MB's is fairly limited - can
someone
explain what a 'Rodbender' is ? I've seen the term
http://indianapolis.craigslist.org/cto/1536521989.html
Any chance it's really gone 250K miles without bending?
Allan
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list archives http://www.okiebenz.com/archive/
To
yes, very good chance.
Allan Streib wrote:
http://indianapolis.craigslist.org/cto/1536521989.html
Any chance it's really gone 250K miles without bending?
Allan
___
http://www.okiebenz.com
For new and used parts go to www.okiebenz.com
To search list
Check out the description of this car. I think the rods are already bent. This
poor seller is in over his head.
http://tiny.cc/ysm4d
Donald H. Snook
-- next part --
An HTML attachment was scrubbed...
URL:
It's quite a shame. Mercedes diesels have such an incredible reputation,
that so many people buy these for super high prices without knowing that
this specific model doesn't live up to the reputation at all.
Tyler
Donald Snook wrote:
Check out the description of this car. I think the rods
Those test will indicate that there is a problem but not the exact
nature of it.
Kaleb C. Striplin (CAT) wrote:
Will a compression or leak down test show bent rods etc?
---
Kaleb C. Striplin
Cox Auto Trader
730-Tulsa FSBO Supervisor
com
___
Local dealer quoted me $140 for a rod, then charged me $190 when I
went to pick it up. I replaced 3 lifters and a few bolts and got to
buy lots of new tools that I'll never use again.
Overall it was a good experience. Cylinders were okay. But I know it
is a ticking time bomb because there was no
If the cylinders and pistons are good, you can fix it for something like
$250 a rod (x6) plus gaskets, rings, etc. I'd budget $2000-2500 if I
were doing all the labor myself.
AFAIK, only MBZ seems to be able to redo the block so that the engine
will last hundreds of kilomiles after the rebuild.
In my case - no. Although I don't have a clue how to interpret leak
down test results, so I did not bother.
You have to pull the head and measure how much each piston protrudes
above the block at the top of it's stroke. Removing the vacuum pump
makes it easier to turn the engine by hand if you
Haley [EMAIL PROTECTED]
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Thursday, November 08, 2007 2:28 PM
Subject: Re: [MBZ] rodbender question
Kaleb C. Striplin (CAT) wrote:
Will a compression or leak down test show bent rods etc?
It should show egged out cylinders and pistons
Are the rod bender motors fixable or is it just a matter of the cost of doing
it? For example, if the rods are bent
and the cylinder worn oval, can it be bored or sleeved? If you have one that
appears to be alright is it wise to
fix it before it gets worse or is it considered hopeless?
Randy
PM
Subject: Re: [MBZ] rodbender question
In my case - no. Although I don't have a clue how to interpret leak
down test results, so I did not bother.
You have to pull the head and measure how much each piston protrudes
above the block at the top of it's stroke. Removing the vacuum pump
Kaleb C. Striplin (CAT) wrote:
Will a compression or leak down test show bent rods etc?
It should show egged out cylinders and pistons after the rods
have been bent a while. (of course, the blue cloud behind
the car indicates much the same thing)
Mitch.
Will a compression or leak down test show bent rods etc?
---
Kaleb C. Striplin
Cox Auto Trader
730-Tulsa FSBO Supervisor
___
http://www.okiebenz.com
For new parts see official list sponsor: http://www.buymbparts.com/
For used parts email [EMAIL PROTECTED]
To
Kaleb C. Striplin, work wrote:
So you have to pull the head to find out, wont show up in a test?
If you have uneven leakdown, you know SOMETHING is wrong.
Never seen a rodbender. How much shorter do the rods get when they bend?
Can you take off the valve springs with a cylinder at TDC and
[EMAIL PROTECTED]
To: Mercedes Discussion List mercedes@okiebenz.com
Sent: Thursday, November 08, 2007 2:51 PM
Subject: Re: [MBZ] rodbender question
Kaleb C. Striplin, work wrote:
So you have to pull the head to find out, wont show up in a test?
If you have uneven leakdown, you know SOMETHING
Check the turbo seals -- lots of oil in the intake with no significant
blowby means the bearings in the turbo are shot, allowing the shaft to
eat the seals. Lotta oil up the intake, usually, followed by serious
oil smoke out the back on acceleration. Usually accompanied by a
lazy turbo
I seem to remember something about NOT sleeving the 350, but the 300 is
sleeved at the factory. New sleeves, rods, pistons, and bearings were
$5000 six or so years ago when I thought I might need to rebuild my
603. More now.
Engine can be rebuilt, but it will likely cost more than a new one,
Stuck rings? Any carbon in the oil pan?
Jim
-Original Message-
From: [EMAIL PROTECTED]
[mailto:[EMAIL PROTECTED] On Behalf Of Kaleb C.
Striplin, work
Sent: Thursday, November 08, 2007 3:38 PM
To: Mercedes Discussion List
Subject: Re: [MBZ] rodbender question
So you have
$10? No, but it's not much higher. I figure someone will come in and out bid
me, so I want to keep later bids lower. I'll come back on Saturday and put in
my official highest bid to hopefully win the auction. We'll see.
--
Luther KB5QHU
Alma, Ark
'83 300SD (236 kmi)
'82 300CD (160 kmi)
'82
Why would you want to go thru the trouble of machining the head to make
the old injectors work when it would be much easier to just use the
newer style injectors?
[EMAIL PROTECTED] wrote:
In a message dated 9/24/2006 12:17:27 P.M. US Mountain Standard Time,
[EMAIL PROTECTED] writes:
In a message dated 9/24/2006 8:01:53 P.M. US Mountain Standard Time,
[EMAIL PROTECTED] writes:
Why would you want to go thru the trouble of machining the head to make
the old injectors work when it would be much easier to just use the
newer style injectors?
Kaleb,
As I mentioned, I
Will a '90 350SDL rod bender head work on a '87 300SDL?
--
Luther KB5QHU
Alma, Ark
'83 300SD (236 kmi)
'82 300CD (160 kmi)
'82 300D (74 kmi) needs MAJOR work
Already bidding and asking how much for shipping and the part number
off of the
head.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItemitem=200030653234
--
Luther KB5QHU
Alma, Ark
'83 300SD (236 kmi)
'82 300CD (160 kmi)
'82 300D (74 kmi) needs MAJOR work
Quoting Kaleb C. Striplin
Do you have an engine that needs it
On 9/24/06, Luther [EMAIL PROTECTED] wrote:
Already bidding and asking how much for shipping and the part number
off of the
head.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItemitem=200030653234
--
Luther KB5QHU
--
OK Don, KD5NRO
Norman, OK
On Sun, 24 Sep 2006 16:25:17 -0500 Luther [EMAIL PROTECTED] wrote:
Already bidding and asking how much for shipping and the part number
off of the
head.
http://cgi.ebay.com/ebaymotors/ws/eBayISAPI.dll?ViewItemitem=200030653234
Do you get the cam, too?
Craig
Getting the cam, valves, etc. would make it that much more desirable.
He also has an IP -- just the thing to send to the Fins for a little re-work!
http://tinyurl.com/zucut
On 9/24/06, Craig McCluskey [EMAIL PROTECTED] wrote:
On Sun, 24 Sep 2006 16:25:17 -0500 Luther [EMAIL PROTECTED] wrote:
http://cgi.ebay.com/ebaymotors/350-SDL-Southern-Car-No-Rust-Turbo-Diesel
-Clean_W0QQitemZ4643645473QQcategoryZ6336QQrdZ1QQcmdZViewItem
This rodbender has 300K on it. How is that possible?
Donald H. Snook
1990 300SEL 127K
1992 Olds 98 122k
They probably clocked it.
-Dave Walton
94S350, 99E300
On 5/26/06, Donald Snook [EMAIL PROTECTED] wrote:
http://cgi.ebay.com/ebaymotors/350-SDL-Southern-Car-No-Rust-Turbo-Diesel
-Clean_W0QQitemZ4643645473QQcategoryZ6336QQrdZ1QQcmdZViewItem
This rodbender has 300K on it. How is that
92 matches
Mail list logo
