>
> I tried doing the virtual image thing with mine and couldn't get it to work.
> I ended up doing the same. You can get cf to USB adapters fairly cheap. And
> did the initial install with my laptop then logged in and fixed the
> networking stuff. I later did a fresh install over pxe using the
On May 22, 2019 6:05 PM, Chris Zakelj wrote:
>
> When I set my 4801 up years and years ago, I did it by using an IDE>CF
> adapter on an old Athlon system I had hanging around rather than messing
> around with virtual images, PXE booting, or the like. The Geode processor
> is roughly equivalent
When I set my 4801 up years and years ago, I did it by using an IDE>CF
adapter on an old Athlon system I had hanging around rather than messing
around with virtual images, PXE booting, or the like. The Geode processor
is roughly equivalent to a Pentium II, so use i386 images. Past that, from
my
> What kernel did you install? I know I'm running i386 on mine, and I'm
> also sure I'd be running amd64 if I could, so I'd say the 4801 can't
> handle amd64 kernels.
I installed i386, of course. Are you running 6.5 on yours?
>
> I never had any trouble booting from a serial console. The
Have you tried
boot> stty com0 38400
boot> set tty com0
On Wed, May 22, 2019 at 2:14 PM Alberto Mijares wrote:
> Hi guys,
>
> I'm new on this list. Greetings everyone.
>
> Here is my case:
>
> I installed OpenBSD on a 4GB Flash Card by attaching the card to a
> Bhyve VM as a "ahci-hd" custom
Hi guys,
I'm new on this list. Greetings everyone.
Here is my case:
I installed OpenBSD on a 4GB Flash Card by attaching the card to a
Bhyve VM as a "ahci-hd" custom drive. Then, booted the VM and disabled
a few of services. Also disabled kernel and libs randomization, since
it's not needed and
With the release of 4.2 I thought I would check again to see if the
vpn1411 still fails with 'Corrupted MAC on input' on a Soekris net4801.
I am happy to say that I can no longer reproduce the error using the
GENERIC kernel.
In the past I could pop up the error within minutes using this
Hi,
Breen Ouellette schrieb:
With the release of 4.2 I thought I would check again to see if the
vpn1411 still fails with 'Corrupted MAC on input' on a Soekris net4801.
I am happy to say that I can no longer reproduce the error using the
GENERIC kernel.
Noticed that too, maybe it's this
Breen Ouellette [EMAIL PROTECTED] wrote:
With the release of 4.2 I thought I would check again to see if the
vpn1411 still fails with 'Corrupted MAC on input' on a Soekris net4801.
I am happy to say that I can no longer reproduce the error using the
GENERIC kernel.
Does anyone know if
Michael [EMAIL PROTECTED] wrote:
Noticed that too, maybe it's this change:
* New MAC algorithm available for data integrity in ssh(1), UMAC-64.
About 20% faster than HMAC-MD5.
ssh still defaults to hmac-md5. umac-64 isn't used unless you
explicitly configure it.
--
Christian naddy
On Tue, Oct 17, 2006 at 08:38:06AM +0200, marc wrote:
same problem
but chris tell me that and it works
Your /etc/ttys file probably doesn't have anything in it for:
tty00 /usr/libexec/getty std.19200 vt100 on secure
the soekris always boots with 19200 by default.
you can change
Stephen Bosch wrote:
Hi:
I have a Soekris net4801 which runs from a compact flash disk. It boots
to the serial console. I've set everything to 9600 baud, 8 bit words, no
parity, 1 stop bit.
When left unattended, it boots normally.
If I try to enter anything at the boot prompt, I see
For the archives, since searching this seems harder than it should be.
-Mike
-Original Message-
From: Stephen Bosch [mailto:[EMAIL PROTECTED]
Sent: Monday, October 16, 2006 1:52 PM
To: Michael Scheliga
Subject: Re: OpenBSD 3.8, Soekris net4801 - console boot hangs when keys
pressed
13 matches
Mail list logo
