I was thinking about what has been recently discussed about the
possibility of measuring frequency via time-stamping samples
referenced to NTP and crunching the numbers. On a different vein, it
would be possible to make a PC output PPS from the internal clock
synchronised to NTP. OK, all the
Hi all,
I need a bit of help getting an old Sulzer D-5 5MHz oscillator to work. It
was built into a rack module with monitoring facilities and had been
slightly 'got-at' by the previous owner. Some of the connections were
pencilled on the case but not enough to give confidence about powering it
Paul can you send me a photo of your oscillator?
Cheers
Rob Kimberley
-Original Message-
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On
Behalf Of Steve Rooke
Sent: 10 October 2008 08:37
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Sulzer Labs
Paul,
Send me a photo as well please. I have a Sulzer 1150 5MHz oscillator and am
curious if it looks the same.
BillWB6BNQ
[EMAIL PROTECTED]
Rob Kimberley wrote:
Paul can you send me a photo of your oscillator?
Cheers
Rob Kimberley
-Original Message-
From: [EMAIL
Hi all,
I need a bit of help getting an old Sulzer D-5 5MHz oscillator to work. It
was built into a rack module with monitoring facilities and had been
slightly 'got-at' by the previous owner. Some of the connections were
pencilled on the case but not enough to give confidence about
Hi Mike,
I ordered the shell, that was easy enough to find once I had a good part
number. I wasn't sure on the coax connector so I bought one of each. I
have a roll of some skinny coax which I believe is RG174, but wasn't
positive. Instead of driving into work to check, I opted to just buy the
On Wed, Oct 8, 2008 at 4:42 PM, Mike S [EMAIL PROTECTED] wrote:
Mouser P/Ns: 152-FM11W1S-K121 (connector shell), 152-FMX006P102 (50
ohm
crimp/solder coax contact for RG-174U sized cable)
At 10:06 AM 10/10/2008, Robert Darlington wrote...
I wasn't sure on the coax connector...not knowing
Hi.
Does anyone know if the Symmetricom SA.31m is pin compatible with standard
OXCOs used in com gear and test instruments?
I would make sense that it was, but then again...
Also, does anyone know off hand the price of new SA.31m's in small quantities?
Thanks!
Jeff
Jeffrey K. Okamitsu,
The reason I asked is that AFIK Austron acquired the Sulzer line and
therefore we can probably go down an Austron route regarding any
documentation.
Rob Kimberley
Paul,
Send me a photo as well please. I have a Sulzer 1150 5MHz oscillator and am
curious if it looks the same.
BillWB6BNQ
Ulrich,
I have been wanting to try your EZGPIB to control and capture data from various
instruments I run in my lab. My GPIB bus typically has 3-6 instruments
connected and I currently use the NI GPIB-ENET/100 as a LAN bridge to any one
of several windows based computers. Ocassionally, I also
Hi. Will the beam tube in a 5071A work in a 5061B?
I suspect not, but I defer to experts out there.
Jeff
Jeffrey K. Okamitsu, PhD, MBA
+1-609-638-5402
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to
Hi all,
I'm using a Trimble Lassen IQ receiver for a Shera style GPSDO. That part
works OK but I would also like to get serial data from the receiver's output
port #2.
The receiver seems to respond to commands sent to port #1 but the desired
outputs don't seem to appear.
Specifically I want
Looking more closely at the software list, I don't see the utility that I
use. Whatever it is, it's a DOS based thing or is at least a shell ap with
just text. I'll dig up the zip file at work when I'm in the office over the
weekend and get it over to you if I still have it. I've used it
13 matches
Mail list logo