Bert may I ask how you created the charts (what software are you using).Thank
You
On Tuesday, April 10, 2018, 9:04:58 a.m. EDT, ewkehren via time-nuts
wrote:
Looking at the pictures it is the same unit I bought. It is not dual oven bit
trimble works with LH right
How did You Pay for them, I cannot make a payment
On Tuesday, April 10, 2018, 2:01:41 p.m. EDT, W7SLS - Scott Scheirman
wrote:
I ordered 2. We shall see
Scott
No connection with seller(s)
Sent from my iPhone
> On Apr 10, 2018, at 7:13 AM, gandalfg8---
Can anybody Explain the operation of the chart in Lady Heather especially the
colors what they represent.Thank You
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow
Hello Everyone I need help on on calibrating Time base oscillators for
counters with Lady Heather's Version 5 Can any one help with the setup for
making measurements.
Thank You
On Wednesday, January 26, 2011, 5:56:16 a.m. EST, Achim Vollhardt
wrote:
Luciano,
you should definitely check this thing out
http://www.four15news.net/biz/?read=8780772
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
I got a EFC-5680A it will not lock. Someone suggested I adjust C217 which
worked, but it drifts slightly back and forth some times when started from a
cold start it will go out of lock, and may or may not relock.
Any suggestions will be appreciated.Thank You
- Original Message -
From:
Hi,
I have been a member of the group for a long time yahoo is not sending email.
Thank You
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
Hi,
I would be interest in receiving the manual.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
Hi Francis,
Thank You for the advise, do you remember which capacitor to disconnect.
Best regards,
Sal C. Cornacchia
From: Francis Grosz fgr...@otiengineering.com
To: time-nuts@febo.com
Sent: Thursday, October 27, 2011 11:37:01 AM
Subject: Re: [time-nuts
Hi Don,
Thank You for the info, I do not have a manual, I will try a few things and see
if it will wok out.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Don Latham d...@montana.com
To: Discussion of precise time
Hi Paul,
I have a Fluke 207-E-5 VLF Receiver with a number of problems, can You help
with a service manual?
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: paul swed paulsw...@gmail.com
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Hello all time-Nuts,
I have a older Bulovaaccuquartz the hands are not moving any ideas on the
problem.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
The information contained in this e-mail transmission is privileged and/or
confidential intended solely
Hi Roberto,
Do You have any idea when the two volume Service Manual for the HP 3586A,B,C
will be uploaded to Your web site.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
The information contained in this e-mail transmission is privileged and/or
confidential
Hi Roberto,
I would be interested?
Thank You
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Roberto Barrios rbarri...@msn.com
To: time-nuts@febo.com
Sent: Mon, November 29, 2010 5:18:07 PM
Subject: [time-nuts] 3586A HQ
Hi Luciano,
Thank You for the information, it will help me to decide on what to get.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Paramithiotti, Luciano Paolo S luciano.paramithio...@hp.com
To: Discussion of precise time
Thank You John, It is working Great. Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: John Miles jmi...@pop.net
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Thu, June 17, 2010 5:38:16 PM
Subject: Re: [time-nuts] how sad
Can some one help me out on lady heather how to change communication port from
com1 to com 3.
Thank You
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Mark Stephens ma...@non-stop.com.au
To: time-nuts@febo.com time-nuts
Hi Warren, how do I change the com port in Lady Heather software.
Thank You
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: WarrenS warrensjmail-...@yahoo.com
To: Discussion of precise time and frequency time-nuts@febo.com
Thank You Bob, I will try it and will advise it it works for me.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bob Camp li...@rtty.us
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Thu
Hi Bert,
Could You tell me how to produced the trace for two timebase oscillators.
Thank You
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bert, VE2ZAZ ve2...@yahoo.ca
To: time-nuts@febo.com
Sent: Wed, March 17, 2010 11:01
Hi John,
Thank You for taking the time, I am relatively New at this and would like to
knows if I am interpreting the reading correctly.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: John Miles jmi...@pop.net
Hello Group members,
I need some help interpreting Lady Heather software results like the colours
and chart results for My Tibold GPS Receiver, any help would be appreciated as
I am new at this.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Hello Group members,
I need some help interpreting Lady Heather software results like the colours
and chart results for My Tbold GPS Receiver, any help would be appreciated as I
am new at this.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Thank You John, I have tried with different sweep speeds both above and below
100 us/div, the problem appears to be no output at all.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: John Ackermann N8UR j...@febo.com
will wait and what he
suggests to do.
Thank You so much for all Your help, a great group of well informed peoples.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Robert Darlington rdarling...@gmail..com
To: Discussion of precise
. Cornacchia
Electronic RF Microwave Engineer (Ret.)
sure or other use is strictly prohibited. If you have received this
notification in error, please immediately contact the sender and delete the
material.
From: Bruce Griffiths bruce.griffi...@xtra.co.nz
It is barely visable on the Tektronix 485.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
The information contained in this e-mail transmission is privileged and/or
confidential intended solely for the exclusive use of the individual addressee.
If you
Oscilloscope and 5345A Counter, the Tbolt software shows all green.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Stan, W1LE stanw...@verizon.net
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Hi Bob,
The pulse is barely visible on the Tektronix 485 it appears to be a very low
output.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bob Camp li...@cq.nu
To: Discussion of precise time and frequency measurement time
Hi Didier,
When the 50 ohms termination is switch on the oscilloscope there is a tiny
positive dot deflecting every second, it appears to have a very low output.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Didier Juges
I cannot measure anything, with the scope set at max sensitivity, there is only
a tiny dot indication every second.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bruce Griffiths bruce.griffi...@xtra.co.nz
To: Discussion
What is the best way to measure or to see any display at the 1 PPS BNC
connector, unfortunately I don't have a digital oscilloscope.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bruce Griffiths bruce.griffi...@xtra.co.nz
Hello everyone I have a Magnavox (Nav-Com Inc.) Model C/GPS Part Number
140254.913 Serial Number 01559 does anyone have any experience what it can be
used for or any information available, thank You for helping.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Hi John Miles,
Is there an instruction manual available for LadyHeather to interpret the
displayed values like PPS, and other values.
Thank You for making such valuable software available to everyone.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Hi Bob,
Can You explain what 10 PPT stands for.
Thank You
From: Bob Camp li...@cq.nu
To: Discussion of precise time and frequency measurement time-n...@febo..com
Sent: Thu, January 21, 2010 7:50:43 AM
Subject: Re: [time-nuts] LPRO Pressure Sensitivity
Hi
Hi Bob,
Thank You for the information, it is very much appreciated, I could not figure
it out without Your help.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Bob Camp li...@cq.nu
To: Discussion of precise time
Hello everyone I have a Magnavox (Nav-Com Inc.) Model C/GPS Part Number
140254.913 Serial Number 01559 does anyone have any experience what it can be
used for or any information available, thank You for helping.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Hello everyone I have a Magnavox (Nav-Com Inc.) Model C/GPS Part Number
140254.913 Serial Number 01559 does anyone have any experience what it can be
used for or any information available, thank You for helping.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret
Can someone help with the software for a Tbolt 35757256 built 6/2/05 A002206,61
Rev E, I just received this unit from China without any information or manual
or software, I am about to built the power supply for it and would appreciate
any help possible
Best regards,
Sal C. Cornacchia
Thank You for the links it will help
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Stanley Reynolds stanley_reyno...@yahoo.com
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Fri, January
the other parts.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: gandal...@aol.com gandal...@aol.com
To: time-nuts@febo.com
Sent: Fri, January 15, 2010 6:53:16 PM
Subject: Re: [time-nuts] need help on Tbolt
In a message dated
Hi Nigel,
You are right it is A002206.G1 I must have pressed the wrong keys.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: gandal...@aol.com gandal...@aol.com
To: time-nuts@febo.com
Sent: Fri, January 15, 2010 6:55:48 PM
issues, managed to
repair some of the but cannot find the proper manual with later revisions, do
You have a manual with later revisions or check the revision numbers on Your.
Thank You
Best regards,
Sal C.. Cornacchia
Electronic RF Microwave Engineer (Ret
(Later
Model), do You have a manual or is any way to check the revision of the plug in
boards.
Thank You for helping out.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: J. Forster j...@quik.com
To: Discussion of precise
. Cornacchia
Electronic RF Microwave Engineer (Ret.)
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
Hi Robert,
Will the Motorola that You have mentioned give a 10.00 MHz output standard.
Thank You
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Robert Atkinson robert8...@yahoo.co.uk
To: Discussion of precise time
Thank You Robert for the quick response.
Best regards,
Sal C. Cornacchia
Electronic RF Microwave Engineer (Ret.)
From: Robert Atkinson robert8...@yahoo.co.uk
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Mon, December
. Cornacchia
Electronic RF Microwave Engineer (Ret.)
___
time-nuts mailing list -- time-nuts@febo.com
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
48 matches
Mail list logo