Dave,
my opinion is that this big tree around your GPS antenna causing a lot of
trouble
as especially when the tree are wet...
Rgds Ernie.
-Original Message-
From: quartz55 quart...@hughes.net
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent:
Hi,
seems to me that the server is OK but minimum activity from the people.
Rgds Ernie.
-Original Message-
From: dzorbini dzorb...@netscape.net
To: time-nuts time-nuts@febo.com
Sent: Thu, Dec 19, 2013 7:19 pm
Subject: [time-nuts] No E-mails
Hello: haven't received any messages for
Hi Bruce,
try to use this one
Resistor Color Code Identification
Rgds Ernie.
-Original Message-
From: Brucekareen brucekar...@aol.com
To: time-nuts time-nuts@febo.com
Sent: Thu, Nov 21, 2013 7:17 pm
Subject: [time-nuts] Off-Topic Question -- German Composition Resistors
While
Hi Bruce,
sorry but the server removed the embedded pics.
here is a link
http://www.diyaudioandvideo.com/Electronics/Color/
Rgds Ernie.
-Original Message-
From: Brucekareen brucekar...@aol.com
To: time-nuts time-nuts@febo.com
Sent: Thu, Nov 21, 2013 7:17 pm
Subject: [time-nuts]
Bob,
please have a look to the flwng link. about the stability..
http://www.jrmiller.demon.co.uk/projects/ministd/stab.htm
Rgds Ernie.
-Original Message-
From: Bob Camp li...@rtty.us
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Thu,
Hi Götz,
very nice handy project, just to watch the TB without a PC.
You should have as a KIT .
Best regards,
Ernie.
-Original Message-
From: Götz Romahn go...@g-romahn.de
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Fri, Aug 23, 2013 6:52 pm
Hi Fred,
there is only a 48Volt connection and some unknown data com I did not use
any mating connector just the power in... everything is available on the front
plate.
Rgds Ernie.
-Original Message-
From: Frederick Bray fwb...@mminternet.com
To: time-nuts time-nuts@febo.com
If you connect to this server../ Internet / and the second RS232 output
from your PC is connected to your GPS receiver then it shows as DGPS mode.
for the GPS unit.but not very simple...
I used it several years ago.. before the WAAS was not fully
activated..it
Hi,
anybody has the Trimble Thunderbolt GPSDO but in a letter size
PCB board from the Hong-Kong epay seller
It has a SMC socket and beside the normal 10 MHz output it has a second
frequency output 9,830400 MHz.
What is the purpose for this freq in the GSM base station...
Please
9:00 AM, Erno Peres wrote:
it has a second frequency output 9,830400 MHz.
What is the purpose for this freq in the GSM base station...
None that I can think of. But it is 8 times the CDMA chip rate of 1.2288
Hz, so would be useful in a CDMA base station
it could be also that the pover supply drops the voltage under nominal load...
looks Ok with no load
-Original Message-
From: J. L. Trantham jlt...@att.net
To: 'Discussion of precise time and frequency measurement' time-nuts@febo.com
Sent: Sun, Jan 13, 2013 1:50 pm
Subject: Re:
Hi Said,
just additional question: did the DC current increased when you started to
blow air
You should run this test / blowing air / minimum 24 hrs.or longer!
Rgds Ernie.
-Original Message-
From: SAIDJACK saidj...@aol.com
To: time-nuts time-nuts@febo.com
Sent:
Hi David,
I am interested about this GPS module but to get here in Hungary it is also
around 60-80 USD...
Rgds Ernie.
-Original Message-
From: David J Taylor david-tay...@blueyonder.co.uk
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Fri, Dec 14,
Hi Gents,
please put me on the list. I should like to have one unit or a KIT.
Rgds Ernie.
-Original Message-
From: Volker Esper ail...@t-online.de
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent: Mon, Nov 19, 2012 8:57 pm
Subject: Re: [time-nuts]
The Saga just goes on...! INFO only.
Rgds Ernie.
Lightsquared Returns With New Proposal For GPS Fix
October 4, 2012
The company asked the FCC to modify its license application so it can use its
5MHz of spectrum that haven’t caused GPS concerns.
LightSquared, the now bankrupt
Chuck,
I have seen already intermittent antenna receptacle on the
back of the TB, also chk all coax connectors for solid contact.
Rgds Ernie.
-Original Message-
From: Chuck Harris cfhar...@erols.com
To: Discussion of precise time and frequency measurement time-nuts@febo.com
Sent:
Hi Chris,
the Kenwood TCXO module is quite adequate because the microwave transverter LO
is the major problem... let say a 10GHz/144 transverter LO xtal osci is
106,500MHz and multiplying up to 10GHz / fxtalX96 / is more critical to get
exact 10368,000MHz
Rgds Ernie.
Hi,
anybody having some experience with this board..
I have the following problemafter power on the board it does not output
any msg only if I use the TrimbleStudio SMT software..on my PC..
Is there any solution to use the board without the PC/software ???
Thanks a
be configured to some extent).
On Mon, Jun 25, 2012 at 1:18 PM, Erno Peres erniepe...@aol.com wrote:
Hi,
anybody having some experience with this board..
I have the following problemafter power on the board it does not
output any msg only if I use the TrimbleStudio SMT software
Hi David,
thanks a lot for the info, I have also the 1PPS output, but had the
impression that it will also output TSIP or any other kind of MSG upon
power-up... and you can configure the board as required of the need.it
outputs according to the TrimbleStudio SW is TEP format but any
Hi David,
I have chked vith TAC32 SW, 9600 Baud and Motorola binary code and it is
working OK. even will initialize the SMT gps board when there is a power
interruption and no any protocol comes out.
Also chked with the Winoncore SW and it display data but not all.. and this
SW does
Hi Ulbrich,
Sorry but not everybody a digital and/or a professional guru... can you please
be a more specific namely to show us the pre filter and other circuitif
you do not mind.
Understand that the key point is the PLL or the phase comparator
circuit.if you want to build
Hi Rich,
please advise which program can I open the files...??
Rgds Ernie.
-Original Message-
From: Rich msima...@sympatico.ca
To: time-nuts time-nuts@febo.com
Sent: Tue, Mar 27, 2012 12:24 am
Subject: Re: [time-nuts] FE5680A x-rays
Ok here they are:
About 30 real-time X-ray
Hi,
have a look at trhis side...
http://www.g4jnt.com/EvenSimplerSimplestGpsdoPossible.htm
Rgds Ernie
-Original Message-
From: Magnus Danielson mag...@rubidium.dyndns.org
To: time-nuts time-nuts@febo.com
Sent: Sat, Mar 10, 2012 5:19 pm
Subject: Re: [time-nuts] DIY GPS-DO
Hi Gents,
received my FE-5680A UN 63401 S/N 0311-61144...
Anybody can advise a few idea about this module..?
From the label I can see it requires +5 Volt but no info about the RS232...
Can I adjust the C field from the DB9 connector
Any info appreciated.
Many thanks and
Hi Chris,
thanks for the info. My second problem is that the unit is in locked position
after powering up but after about 5-8min the freq goes down slowly about
9.999.997.3 Hz and the lock ind level is still low.
Also noticed that during the sweep the max freq is 10.000.004 Hz and the
Hi Nevell,
FYI my one delivers almost +5dBm on 50 Ohm.Ref Voltage +4,86 Volt.
Rgds Ernie.
-Original Message-
From: Scott Newell newell+timen...@n5tnl.com
To: time-nuts time-nuts@febo.com
Sent: Thu, Feb 9, 2012 5:16 am
Subject: [time-nuts] Morion MV89 output level?
Got my
Hi Ray,
please find on this link the info what you are looking for.
http://www.jrmiller.demon.co.uk/projects/ministd/frqstd.htm
Rgds Ernie.
-Original Message-
From: Ray Xu rayxu...@gmail.com
To: time-nuts time-nuts@febo.com
Sent: Sun, Jan 29, 2012 7:51 am
Subject:
This is why the North-Italy territory wants to be separeted the rest of
Italy..hihi
EP.
-Original Message-
From: David C. Partridge david.partri...@perdrix.co.uk
To: 'Discussion of precise time and frequency measurement' time-nuts@febo.com
Sent: Mon, Jan 16, 2012
Hello,
I have a Temex RMO 10MHz rubidium osci but no lock signal comes out.
Checking the RS232 diag code I have the flwng hex code:
7D 04 39 8B 41 4A 48 CB
where the second HEX code indicating the Rb signal level which is in my case
is almost zero and it
Hi Don,
this type of receiver sometimes need a good 15-20 min to find their place...
they are not very sensitive...
also if the receiver comes-up in NMEA mode then they probably used a spec
application and it
is much better to config the 20 pin connectors to Rockwell-binarymode
...@febo.com] On
ehalf Of Erno Peres
ent: Saturday, January 07, 2012 8:40 AM
o: shali...@gmail.com; time-nuts@febo.com
ubject: Re: [time-nuts] Getting my Rockwell D200 GPS to work
i Don,
this type of receiver sometimes need a good 15-20 min to find their place...
hey are not very sensitive...
lso
Hi,
I also would use an adjustable PS and checking the output RF level to see
if the RF level is increasing while incraising the DC voltage... when the
output amplitude is not changing anymore then it should be the operating DC
voltage
or chk the outcoming Ref DC voltage.
Rgds Ernie.
Hi Jeff,
looks like the UPS battery and the 5061B draws too much currenttogether
just charge-up the UPS and when it is OK plug the other unit in
This is my first guess.
Rgds Ernie..
-Original Message-
From: Jeffrey Okamitsu w...@w3kl.com
To: Time Nuts
34 matches
Mail list logo