if ubi part fails, reset also mtd_devs to 0, as
further ubi part would use wrong mtd_devs.
Signed-off-by: Heiko Schocher h...@denx.de
---
This issue was posted from Andrew here:
http://patchwork.ozlabs.org/patch/410507/
Patchwork [U-Boot] ubi: reset relevant globals in ubi_exit()
Could this
On Mon, 2015-01-19 at 20:04 +0100, Hans de Goede wrote:
Hi,
On 17-01-15 23:51, Ian Campbell wrote:
On Thu, 2015-01-15 at 15:52 +0100, Hans de Goede wrote:
According to the Cortex-A7 MPCore Technical Reference Manual:
You must ensure this bit is set to 1 before the caches and MMU are
On Mon, 2015-01-19 at 20:44 +0100, Hans de Goede wrote:
Hi,
On 17-01-15 23:59, Ian Campbell wrote:
On Thu, 2015-01-15 at 15:52 +0100, Hans de Goede wrote:
Add initial sun9i (A80) support, only uart + mmc are supported for now.
Signed-off-by: Hans de Goede hdego...@redhat.com
On Mon, 2015-01-19 at 10:55 -0700, Stephen Warren wrote:
* Indicate that boot.scr is fully supported, not a legacy option.
Still, recommend use of extlinux.conf over boot.scr.
Thanks for this. The bits around that look fine now.
One thing I happened to spot while skimming:
+handled by
Hello Dashi Cao,
On Tue, 20 Jan 2015 14:12:35 +0800, Da Shi Cao dscao...@gmail.com
wrote:
In standalone applications, it seems that the execution of printf
function in U-Boot is dependent on the value of register R9, which is
setup in app_startup. But r9 can be used by your program at the
On Mon, 2015-01-19 at 11:29 +0100, Hans de Goede wrote:
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend engine to do the dma from
memory, as the
- use linux display timing settings
- change backlight duty cycle 500ns
- some defaultenvironment changes
- change fit_addr_r to 0x1400 as needed if
MAX_LOCKDEP_SUBCLASSES in linux gets increased.
- Environment now at 0xd in nand flash
Signed-off-by: Heiko Schocher h...@denx.de
---
On Mon, 19 Jan 2015 06:29:47 +0200
Siarhei Siamashka siarhei.siamas...@gmail.com wrote:
On Sun, 04 Jan 2015 20:49:38 +0100
Hans de Goede hdego...@redhat.com wrote:
Hi,
On 04-01-15 20:19, Michal Suchanek wrote:
Setting magic 'reserved' hpcr bit on sun5i DEBE seems required for
On Mon, 2015-01-19 at 15:35 +0100, Hans de Goede wrote:
Siarhei, thanks for bringing this topic up once again, I agree that this
is ideally something which we should fix. The problem is that the only
way to know that any new settings which we do are actually good, is to
test them on lots of
On Tuesday, January 20, 2015 at 07:12:35 AM, Da Shi Cao wrote:
In standalone applications, it seems that the execution of printf
function in U-Boot is dependent on the value of register R9, which is
setup in app_startup. But r9 can be used by your program at the
decision of gcc compilation
On Friday, December 19, 2014 at 05:39:13 AM, Peng Fan wrote:
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel gpmi-nand.c driver with each
data block 512 bytes.
Hi Albert,
On Tue, 2015-01-20 at 08:07 +0100, Albert ARIBAUD wrote:
Hello Alexey,
On Mon, 19 Jan 2015 20:55:03 +0300, Alexey Brodkin
alexey.brod...@synopsys.com wrote:
In case of CONFIG_SYS_MALLOC_F_LEN malloc_base is used for early
start-up code and is set very early, typically in
Hello Hans,
On Mon, 19 Jan 2015 20:04:58 +0100, Hans de Goede hdego...@redhat.com
wrote:
Hi,
On 17-01-15 23:51, Ian Campbell wrote:
On Thu, 2015-01-15 at 15:52 +0100, Hans de Goede wrote:
According to the Cortex-A7 MPCore Technical Reference Manual:
You must ensure this bit is set to
Hello Thomas,
On Tue, 20 Jan 2015 19:34:32 +0800, Da Shi Cao dscao...@gmail.com
wrote:
No, I didn't use that option. This option should fix it.
Please also look at other options used for hello_world, as you might hit
other compatibility-related issues if you're not using the same ones.
Hi Simon,
On Tue, Jan 20, 2015 at 11:19 AM, Simon Glass s...@chromium.org wrote:
In commit a62e84d the old functionality of obtaining a PCI address from the
'reg' property was lost. Add it back, so we can support both a compatible
string list and a 'reg' property.
This patch fixes PCIe
Hi Simon,
On Mon, 2015-01-19 at 16:34 -0700, Simon Glass wrote:
Hi Andreas,
Why do you need manual reloc? Is this a toolchain bug?
From my experience the only way to escape manual relocation is to use
PIE (Position Independent Executable), but this might not be supported
in a toolchain for
On Friday, December 19, 2014 at 05:39:12 AM, Peng Fan wrote:
Calculate ecc strength according oobsize, but not hardcoded
which is not aligned with kernel driver
Signed-off-by: Peng Fan peng@freescale.com
Signed-off-by: Ye.Li b37...@freescale.com
Reviewed-by: Marek Vasut ma...@denx.de
On Tuesday, January 20, 2015 at 07:35:26 AM, Peng Fan wrote:
Hi Marek,
Since you are familiar with this driver, would you please help review
this patch?
Hi!
I commented on both. Next time, please CC me and Stefano, since the patches
might slip just like this one did.
Thank you for this
No, I didn't use that option. This option should fix it.
Thanks a lot.
Thomas
On Tue, Jan 20, 2015 at 5:37 PM, Albert ARIBAUD
albert.u.b...@aribaud.net wrote:
Hello Dashi Cao,
On Tue, 20 Jan 2015 14:12:35 +0800, Da Shi Cao dscao...@gmail.com
wrote:
In standalone applications, it seems that
Signed-off-by: Andreas Bießmann andreas.de...@googlemail.com
---
arch/avr32/config.mk|3 +++
arch/avr32/cpu/u-boot.lds |2 ++
arch/avr32/include/asm/config.h |1 +
arch/avr32/include/asm/u-boot.h |7 +++
arch/avr32/lib/Makefile |2 ++
Hi,
On 20-01-15 09:16, Siarhei Siamashka wrote:
On Mon, 19 Jan 2015 06:29:47 +0200
Siarhei Siamashka siarhei.siamas...@gmail.com wrote:
On Sun, 04 Jan 2015 20:49:38 +0100
Hans de Goede hdego...@redhat.com wrote:
Hi,
On 04-01-15 20:19, Michal Suchanek wrote:
Setting magic 'reserved'
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede hdego...@redhat.com
---
drivers/video/Kconfig | 15 +--
Add support for Hitachi tx18d42vm LVDS LCD panels, these panels have a
lcd controller which needs to be initialized over SPI, once that is
done they work like a regular LVDS panel.
Signed-off-by: Hans de Goede hdego...@redhat.com
---
board/sunxi/Kconfig | 7 +++
Hi Anatolij,
Here is v2 of my Hitachi tx18d42vm LVDS LCD support patches. You already
acked v1, but v1 was sunxi specific and following the example of the ssd2828
patches I've decided to respin the patch to make the hitachi tx18d42vm bits
generic so that they can be used by non sunxi boards too.
Hi, Marek
On 1/20/2015 7:04 PM, Marek Vasut wrote:
On Tuesday, January 20, 2015 at 07:35:26 AM, Peng Fan wrote:
Hi Marek,
Since you are familiar with this driver, would you please help review
this patch?
Hi!
I commented on both. Next time, please CC me and Stefano, since the patches
might
Hello Heiko
Thank you fro the review. I added atomic_long_read in ubifs.h as
for other atomic operations.
I hope (but I can't garantee) by this time the mail is well
formed. If not please tell me again.
During mount_ubifs the ubifs_replay_journal was disabled. This patch
enables it again and
Hi,
On 19-01-15 21:16, Priit Laes wrote:
Gemei G9 is an A10 based tablet, with 1G RAM, 16G NAND, 1024x768
IPS LCD display, stereo speakers, 1.3MP front camera and 5 MP
rear camera, 8000mAh battery, GT901 2+1 touchscreen, Bosch BMA250
accelerometer and RTL8188CUS USB wifi. It also has MicroSD
Hi, Marek
On 1/20/2015 7:03 PM, Marek Vasut wrote:
On Friday, December 19, 2014 at 05:39:13 AM, Peng Fan wrote:
If ecc chunk data size is 512 and oobsize is bigger than 512, there is
a chance that block_mark_bit_offset conflicts with bch ecc area.
The following graph is modified from kernel
On 01/20/15 09:15, Peng Fan wrote:
This patch add DT support for mxc gpio driver.
Include a bank_index entry in platdata. This can avoid using
`plat - mxc_plat` to calculate bank number. Also this can simplify code.
Although, I don't insist, but I would recommend to split the patch into 2:
Thank you very much for this Peter, it's much appreciated, and should
hopefully stop anyone else falling into the same trap!
Thanks!
Dave George
On 16/01/2015 17:08, Peter Tyser wrote:
Hi David,
It looks like the entry point is 0x4. Why does the tutorial state
that the example needs
Hello Simon,
On Mon, 19 Jan 2015 12:39:34 -0700, Simon Glass s...@chromium.org
wrote:
Hi Albert,
On 18 January 2015 at 23:54, Albert ARIBAUD albert.u.b...@aribaud.net wrote:
Hello Simon,
On Sun, 18 Jan 2015 11:55:36 -0700, Simon Glass s...@chromium.org
wrote:
At present SPL uses a
On 01/20/2015 12:29 AM, Andreas Bießmann wrote:
This is the first attempt to add generic board support to avr32 architecture.
It
has at least one relevant part for other manual reloc architectures.
This series is currently runtime tested on grasshhopper only. I expect some
changes
Hi,
I'm working on the improvement of the recipes of u-boot in the Poky
reference system of Yocto project.
To do this, I need to fully understand the build system used in
u-boot, mainly the u-boot tools (tools, env ..).
My questions are:
- what is the build system used in u-boot?
- Does this
This is the first attempt to add generic board support to avr32 architecture. It
has at least one relevant part for other manual reloc architectures.
This series is currently runtime tested on grasshhopper only. I expect some
changes regarding LCD support when testing the code on atstk1002. The
+Thierry
Hi Bin,
On 20 January 2015 at 05:59, Bin Meng bmeng...@gmail.com wrote:
Hi Simon,
On Tue, Jan 20, 2015 at 11:19 AM, Simon Glass s...@chromium.org wrote:
In commit a62e84d the old functionality of obtaining a PCI address from the
'reg' property was lost. Add it back, so we can
Hi,
On 20-01-15 11:22, Albert ARIBAUD wrote:
Hello Hans,
On Mon, 19 Jan 2015 20:04:58 +0100, Hans de Goede hdego...@redhat.com
wrote:
Hi,
On 17-01-15 23:51, Ian Campbell wrote:
On Thu, 2015-01-15 at 15:52 +0100, Hans de Goede wrote:
According to the Cortex-A7 MPCore Technical Reference
Hi,
On 20-01-15 10:14, Ian Campbell wrote:
On Mon, 2015-01-19 at 11:29 +0100, Hans de Goede wrote:
Testing has shown that on sun4i the display backend engine does not have
deep enough fifo-s causing flickering / tearing in full-hd mode due to
fifo underruns. On sun4i use the display frontend
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family only.
Change-Id: Ie27a945c9fe79d044cc886e269b60747f1744116
Signed-off-by: Volodymyr Riazantsev volodymyr.riazant...@globallogic.com
---
drivers/mmc/fsl_esdhc.c | 8 ++--
include/configs/mx6_common.h | 2 ++
Hi Pantelis,
On Mon, Jan 19, 2015 at 10:47 AM, Pantelis Antoniou
pantelis.anton...@gmail.com wrote:
Hi Volodymyr,
On Jan 14, 2015, at 22:46 , Volodymyr Riazantsev
volodymyr.riazant...@globallogic.com wrote:
Add support of the DDR mode for eSDHC driver.
Enable it for i.MX6 SoC family
commit a62e84d7b1824a202dd incorrectly changed the tegra pci code to the
new fdtdec pci helpers. To get the device index of the root port, the
reg property should be parsed from the dtb (as was previously the
case).
With this patch i can successfully network boot my jetson tk1
Signed-off-by:
On Mon, Jan 19, 2015 at 06:33:43PM +0100, Paul Kocialkowski wrote:
When booting from USB peripheral boot, the bootrom will not properly deinit
the
MUSB controller, which doesn't clearly indicate an USB disconnection to the
host
and leaves U-Boot to deal with the state of the previous USB
Hi Tom,
On 1 December 2014 at 17:48, Simon Glass s...@chromium.org wrote:
This series adds eDP support for nyan-bg so that the display works.
Nyan-big is based on tegra124.
Some support is added for new clocks to make this work. The drm_dp_helper.h
file is brought in from Linux since many
(Corrected the u-boot list address in the cc of this thread and added
Kevin hilman who is also quite interested in this topic)
On Tue, 2015-01-20 at 10:36 +0100, Sjoerd Simons wrote:
Hey Suriyan,
I just noticed the patchset Akshay Saraswat sent (Add support for
booting multiple cores),
Sorry, missed this. Yes, looks good to me. I can apply it to
u-boot-tegra/master, or TomR can take it in to master U-Boot directly.
Tom
-Original Message-
From: Stephen Warren [mailto:swar...@wwwdotorg.org]
Sent: Monday, January 19, 2015 3:57 PM
To: u-boot@lists.denx.de; Simon
I've merged that patch series w/u-boot-tegra/next and /master, done a MAKEALL
-s tegra, and rebased against ARM /master and pushed to denx.de.
Stephen - please test and if it looks OK, I'll prepare a PR.
-Original Message-
From: Tom Warren
Sent: Tuesday, January 20, 2015 8:28 AM
To:
Hello Kevin,
On Tue, Jan 20, 2015 at 3:38 PM, Suriyan Ramasami suriya...@gmail.com wrote:
Hello Kevin,
On Tue, Jan 20, 2015 at 3:29 PM, Suriyan Ramasami suriya...@gmail.com wrote:
Hello Kevin,
On Tue, Jan 20, 2015 at 2:43 PM, Kevin Hilman khil...@kernel.org wrote:
Suriyan Ramasami
On Thu, Jan 15, 2015 at 08:39:45PM +, Alexey Brodkin wrote:
Dear Tom,
The following changes since commit
28c4dae114c9b94b2ad81d4da716e9fc2cba:
Merge branch 'next' of git://git.denx.de/u-boot-video (2015-01-14
16:26:15 -0500)
are available in the git repository at:
On Mon, Jan 19, 2015 at 05:50:26PM +0200, Pantelis Antoniou wrote:
The following changes since commit ab77f24119e80257de4ab017b877f92f96980562:
Merge branch 'master' of git://git.denx.de/u-boot-ti (2015-01-16 10:25:01
-0500)
are available in the git repository at:
On Sun, Jan 18, 2015 at 12:33:47PM +0100, Marek Vasut wrote:
The following changes since commit ab77f24119e80257de4ab017b877f92f96980562:
Merge branch 'master' of git://git.denx.de/u-boot-ti (2015-01-16 10:25:01
-0500)
are available in the git repository at:
- add bcm_usb_gadget.c
- implement fastboot on 'bcm28155_ap' boards
Signed-off-by: Steve Rae s...@broadcom.com
---
drivers/usb/gadget/Makefile | 2 +
drivers/usb/gadget/bcm_usb_gadget.c | 240
include/configs/bcm28155_ap.h | 20 ++-
3 files
Suriyan Ramasami suriya...@gmail.com writes:
Hello Kevin,
These are the changes that would be necessary in uboot mainline for SPL:
arch/arm/cpu/armv7/exynos/Kconfig
- select OF_CONTROL
+ select SUPPORT_SPL
+ select OF_CONTROL if !SPL_BUILD
Akshay Saraswat aksha...@samsung.com writes:
This patch series introduces changes for booting secondary CPUs
on Exynos5420 and Exynos5800.
Thanks for this series. I think this should help get the odroid-xu3
behave better with the mainline linux kernel (assuming I can get it
working with
On Thu, Jan 15, 2015 at 10:18:01AM +0100, Pali Rohár wrote:
On Thursday 15 January 2015 10:07:05 Pali Rohár wrote:
Hello,
when starting U-Boot (from git master) on Nokia N900 it show
lot of these lines on N900 screen:
Timed out in wait_for_event: status=
Check if pads/pull-ups
Since a complete gadget implementation is not available yet,
this series provides a method for interfacing the existing gadget
code with the UDC driver code.
Steve Rae (4):
usb: gadget: fastboot: add CONFIG_FASTBOOT_NO_GADGET support
usb: add 'bcm_udc_otg' support
usb: update 'sysmap.h'
Hello Suriyan,
Suriyan Ramasami suriya...@gmail.com writes:
Hello Sjoerd Simons,
A signed BL2 which allows unsigned BL2 chain load is already
available for experimentation. Refer this link:
http://forum.odroid.com/viewtopic.php?f=98t=6147#p58984
The suriyan.bl2-hkxu3.1212.5422.zip blob
Hello Kevin,
On Tue, Jan 20, 2015 at 3:29 PM, Suriyan Ramasami suriya...@gmail.com wrote:
Hello Kevin,
On Tue, Jan 20, 2015 at 2:43 PM, Kevin Hilman khil...@kernel.org wrote:
Suriyan Ramasami suriya...@gmail.com writes:
Hello Kevin,
These are the changes that would be necessary in uboot
On 01/14/2015 05:34 PM, Marek Vasut wrote:
On Wednesday, January 14, 2015 at 05:40:41 PM, dingu...@opensource.altera.com
wrote:
From: Dinh Nguyen dingu...@opensource.altera.com
Hi!
This adds the code to configure the SDRAM controller that is found in the
SoCFGPA Cyclone5 and Arria5
On Tue, Dec 23, 2014 at 12:04:53PM -0700, Simon Glass wrote:
This does nothing now, so drop it. We have SPL anyway to do our low-level
init.
Signed-off-by: Simon Glass s...@chromium.org
Acked-by: Ian Campbell i...@hellion.org.uk
Applied to u-boot/master, thanks!
--
Tom
signature.asc
On Tue, Dec 23, 2014 at 12:04:55PM -0700, Simon Glass wrote:
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass s...@chromium.org
Applied to
On Tue, Dec 23, 2014 at 12:04:57PM -0700, Simon Glass wrote:
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass s...@chromium.org
Acked-by: Stefano
On Fri, Dec 19, 2014 at 04:53:24PM -0500, Tom Rini wrote:
Prior to this change we set the gd pointer early so that we can store
data in it. This becomes problematic for DM changes as well as being
odd in general. Re-work the code paths so that we don't need to set the
gd pointer so early
On Tue, Dec 23, 2014 at 12:04:58PM -0700, Simon Glass wrote:
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass s...@chromium.org
Applied to
On Sat, Jan 17, 2015 at 02:09:13AM -0500, Sinan Akman wrote:
Signed-off-by: Sinan Akman si...@writeme.com
Cc: kim.phill...@freescale.com
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: Digital signature
___
U-Boot mailing
All of the code in arch/arm/cpu/armv7/sunxi/board.c was under a check
for CONFIG_SPL_BUILD so instead only build for SPL. This lets us drop a
hunk of code that was never enabled.
Cc: Hans de Goede hdego...@redhat.com
Cc: Ian Campbell i...@hellion.org.uk
Signed-off-by: Tom Rini tr...@ti.com
---
On Sat, Jan 17, 2015 at 06:54:52PM -0500, Sinan Akman wrote:
Signed-off-by: Sinan Akman si...@writeme.com
Cc: Tom Rini tr...@ti.com
Applied to u-boot/master, thanks!
--
Tom
signature.asc
Description: Digital signature
___
U-Boot mailing list
On Tue, Dec 23, 2014 at 12:04:56PM -0700, Simon Glass wrote:
The global_data pointer (gd) has already been set before board_init_f()
is called. We should not assign it again. We should also not use gdata since
it is going away.
Signed-off-by: Simon Glass s...@chromium.org
Acked-by: Igor
On Tue, Dec 23, 2014 at 12:04:51PM -0700, Simon Glass wrote:
We need to get rid of this SPL-specific setting of the global_data pointer.
It is already set up in start.S immediately before board_init_f() is called,
and there may be information there that is needed (e.g. pre-reloc malloc
info).
On Tue, Dec 23, 2014 at 12:04:52PM -0700, Simon Glass wrote:
The current sunxi implementation uses gdata, which is going away. It also
sets up DRAM before board_init_f() in SPL.
There is really no reason to do much in s_init() since board_init_f() is
called immediately afterwards. The only
Hello Kevin,
These are the changes that would be necessary in uboot mainline for SPL:
arch/arm/cpu/armv7/exynos/Kconfig
- select OF_CONTROL
+ select SUPPORT_SPL
+ select OF_CONTROL if !SPL_BUILD
configs/odroid-xu3_defconfig
+CONFIG_SPL=y
include/configs/odroid_xu3.h
#undef
Add the required definitions for the USB OTG interface.
Signed-off-by: Steve Rae s...@broadcom.com
---
arch/arm/include/asm/arch-bcm281xx/sysmap.h | 141
1 file changed, 141 insertions(+)
diff --git a/arch/arm/include/asm/arch-bcm281xx/sysmap.h
Implement the UDC support for the USB OTG interface.
Signed-off-by: Steve Rae s...@broadcom.com
---
This commit is not checkpatch clean - however, there seems to be
no way to remove this warning:
warning: drivers/usb/gadget/bcm_udc_otg.c,97:
Adding new packed members is to be done
Implement fastboot_func_init() which provides a minimalistic setup
of the USB endpoints and requests required by the fastboot gadget.
Signed-off-by: Steve Rae s...@broadcom.com
---
drivers/usb/gadget/f_fastboot.c | 39 +++
1 file changed, 39 insertions(+)
On 12 January 2015 at 18:02, Simon Glass s...@chromium.org wrote:
Add a dm_ prefix to driver model I2C functions so that we can keep the old
ones around.
This is a little unfortunate, but on reflection it is too difficult to
change the API. We can undo this rename when most boards and drivers
On 12 January 2015 at 18:02, Simon Glass s...@chromium.org wrote:
For boards which use multiple I2C devices, or for SOCs which support
multiple boards, we might want to convert these to driver model at different
times. At present this is difficult because we need to either use
CONFIG_DM_I2C
On 15 January 2015 at 09:19, Simon Glass s...@chromium.org wrote:
Since GPIO support has now moved to the driver model uclass, we can drop
this include.
Signed-off-by: Simon Glass s...@chromium.org
---
lib/fdtdec.c | 2 --
1 file changed, 2 deletions(-)
Applied to u-boot-dm.
Hi,
On Wed, Jan 21, 2015 at 3:05 AM, Simon Glass s...@chromium.org wrote:
Hi Sjoerd,
On 20 January 2015 at 10:06, Sjoerd Simons
sjoerd.sim...@collabora.co.uk wrote:
commit a62e84d7b1824a202dd incorrectly changed the tegra pci code to the
new fdtdec pci helpers. To get the device index of
Exynos5420 has different registers with other exynos5 SoCs to control
usb device phy, so need separated function to enable exynos5420 usb
device phy.
Signed-off-by: Joonyoung Shim jy0922.s...@samsung.com
---
I used usbdev instead of usbdrd on function name because registers
name prefix is
Hi, Igor
On 1/20/2015 10:39 PM, Igor Grinberg wrote:
On 01/20/15 09:15, Peng Fan wrote:
This patch add DT support for mxc gpio driver.
Include a bank_index entry in platdata. This can avoid using
`plat - mxc_plat` to calculate bank number. Also this can simplify code.
Although, I don't
Signed-off-by: Sinan Akman si...@writeme.com
---
board/freescale/mpc837xerdb/mpc837xerdb.c |7 ++-
1 files changed, 6 insertions(+), 1 deletions(-)
diff --git a/board/freescale/mpc837xerdb/mpc837xerdb.c
b/board/freescale/mpc837xerdb/mpc837xerdb.c
index e0a1031..565f815 100644
---
Hi Simon,
On Tue, Jan 20, 2015 at 10:31 PM, Simon Glass s...@chromium.org wrote:
+Thierry
Hi Bin,
On 20 January 2015 at 05:59, Bin Meng bmeng...@gmail.com wrote:
Hi Simon,
On Tue, Jan 20, 2015 at 11:19 AM, Simon Glass s...@chromium.org wrote:
In commit a62e84d the old functionality of
This commit 904672e (lcd: refactor lcd console stuff into its
own file), which cause lcd console address is not initialized.
This patch split lcd console address initialize and lcd logo
display into two functions.
Signed-off-by: Bo Shen voice.s...@atmel.com
---
common/lcd.c | 11 ---
1
The dwc3_set_mode function is used only in
drivers/usb/host/xhci-exynos5.c so make it to static.
Signed-off-by: Joonyoung Shim jy0922.s...@samsung.com
---
drivers/usb/host/xhci-exynos5.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/drivers/usb/host/xhci-exynos5.c
Signed-off-by: Masahiro Yamada yamad...@jp.panasonic.com
---
Changes in v2:
- Fix umc_init.c too
arch/arm/cpu/armv7/uniphier/ph1-ld4/pll_init.c | 6 +++---
arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c | 4 ++--
arch/arm/cpu/armv7/uniphier/ph1-pro4/pll_init.c | 6 +++---
The inlining is done by GCC when needed, there is no need to do it
explicitly. Furthermore, the inline keyword does not force-inline
the code, but is only a hint for the compiler.
Signed-off-by: Masahiro Yamada yamad...@jp.panasonic.com
---
arch/arm/cpu/armv7/uniphier/ph1-ld4/umc_init.c | 4
Hello Kevin,
On Tue, Jan 20, 2015 at 2:43 PM, Kevin Hilman khil...@kernel.org wrote:
Suriyan Ramasami suriya...@gmail.com writes:
Hello Kevin,
These are the changes that would be necessary in uboot mainline for SPL:
arch/arm/cpu/armv7/exynos/Kconfig
- select OF_CONTROL
+
Hi Kevin,
Akshay Saraswat aksha...@samsung.com writes:
This patch series introduces changes for booting secondary CPUs
on Exynos5420 and Exynos5800.
Thanks for this series. I think this should help get the odroid-xu3
behave better with the mainline linux kernel (assuming I can get it
Hello Alexey,
On Tue, 20 Jan 2015 13:06:57 +, Alexey Brodkin
alexey.brod...@synopsys.com wrote:
Hi Albert,
On Tue, 2015-01-20 at 08:07 +0100, Albert ARIBAUD wrote:
Hello Alexey,
On Mon, 19 Jan 2015 20:55:03 +0300, Alexey Brodkin
alexey.brod...@synopsys.com wrote:
In case of
if CONFIG_AT91SAM9_WATCHDOG is set, do not disable WDT in
SPL
Signed-off-by: Heiko Schocher h...@denx.de
---
arch/arm/cpu/at91-common/spl.c | 4
1 file changed, 4 insertions(+)
diff --git a/arch/arm/cpu/at91-common/spl.c b/arch/arm/cpu/at91-common/spl.c
index 6473320..aaa5eec 100644
---
call hw_watchdog_init() also if CONFIG_AT91SAM9_WATCHDOG
is used.
Signed-off-by: Heiko Schocher h...@denx.de
---
common/board_f.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
diff --git a/common/board_f.c b/common/board_f.c
index 3a4b32c..693a75c 100644
--- a/common/board_f.c
+++
enable WDT for the taurus board.
Signed-off-by: Heiko Schocher h...@denx.de
---
include/configs/taurus.h | 6 ++
1 file changed, 6 insertions(+)
diff --git a/include/configs/taurus.h b/include/configs/taurus.h
index 65468ad..b61dc2d 100644
--- a/include/configs/taurus.h
+++
make the HW WDT timeout configurable through the define
CONFIG_AT91_HW_WDT_TIMEOUT.
Signed-off-by: Heiko Schocher h...@denx.de
---
README | 3 +++
drivers/watchdog/at91sam9_wdt.c | 4
2 files changed, 7 insertions(+)
diff --git a/README b/README
index
Masahiro Yamada (3):
ARM: UniPhier: use linux/sizes.h for readability
ARM: UniPhier: rename SG_MEMCONF_* macros for readability
ARM: UniPhier: add SG_MEMCONF macros for DDR channel 2
arch/arm/include/asm/arch-uniphier/sg-regs.h | 109 +++
1 file changed, 77
PH1-sLD3, PH1-LD6b have DDR channel 2.
Signed-off-by: Masahiro Yamada yamad...@jp.panasonic.com
---
Changes in v2: None
arch/arm/include/asm/arch-uniphier/sg-regs.h | 44
1 file changed, 44 insertions(+)
diff --git a/arch/arm/include/asm/arch-uniphier/sg-regs.h
add reset controller status register
Signed-off-by: Heiko Schocher h...@denx.de
---
arch/arm/include/asm/arch-at91/at91_rstc.h | 2 ++
1 file changed, 2 insertions(+)
diff --git a/arch/arm/include/asm/arch-at91/at91_rstc.h
b/arch/arm/include/asm/arch-at91/at91_rstc.h
index a942342..e4eb3da
Hello Hans,
On Tue, 20 Jan 2015 15:32:34 +0100, Hans de Goede hdego...@redhat.com
wrote:
Hi,
On 20-01-15 11:22, Albert ARIBAUD wrote:
Hello Hans,
I'm leaning toward grouping all CP15 inits (including cache(s)
and TLB disabling and maybe VBAR setting) in a single CP15 call to
a
Hello Jakub,
On Tue, 20 Jan 2015 20:09:21 +0100, Jakub Jančo kub...@gmail.com
wrote:
Hello,
I want to disable uboot tftp on my device and if uboot allow some
login/access(eg. by console) then disable it too.
My aim is to lock uboot except booting image(OS), I want manage it only
from
Hello Konstantyn,
Am 20.01.2015 17:09, schrieb Konstantyn Prokopenko:
Hello,
I'm using the latest u-boot on our custom board. The u-boot is located on the
NAND flash in the first 4MB partition. I break 256MB NAND into 4 MTD
partitions: u-boot(4MB), kernel(4MB), rootfs(100MB), safefs(40MB),
Signed-off-by: Masahiro Yamada yamad...@jp.panasonic.com
---
Changes in v2:
- Split into two patches
arch/arm/include/asm/arch-uniphier/sg-regs.h | 25 +
1 file changed, 13 insertions(+), 12 deletions(-)
diff --git a/arch/arm/include/asm/arch-uniphier/sg-regs.h
Match the suffixes of SG_MEMCONF_* macros with SZ_* macros defined
by linux/sizes.h for readability.
Signed-off-by: Masahiro Yamada yamad...@jp.panasonic.com
---
Changes in v2:
- Split into two patches
arch/arm/include/asm/arch-uniphier/sg-regs.h | 40 ++--
1 file
Hello Anton,
Am 20.01.2015 15:22, schrieb Anton Habegger:
Hello Heiko
Thank you fro the review. I added atomic_long_read in ubifs.h as
for other atomic operations.
Hmm.. I see, there are other missing atomic defines for UBI also ...
Ok, I tend to accept your patch, but the correct way would
1 - 100 of 105 matches
Mail list logo
