Hi,
Could somebody comment on storage options i.e Gluster or Ceph and when to use
each one?
Looking for an architecture which is fully redundant, both at the hypervisor
level and at the storage level so needs to include data replication.
thx
___
Version: 4.5.1
Configure the HCI mode on the cockpit web interface, and the message "glusterfs
Host is not in 'Peer in Cluster' state" is displayed.
node1 gluster peer status normally shows three storage nodes
#gluster peer status
Number of Peers: 2
Hostname: 10.10.1.6
Uuid:
Hi everyone.
I have deployed a 3x replica glusterfs succesfully.
I have 4 nic in each server. Will be using 2 bond, one for gluster and the
other for the vm. My doubt is:
Actually, my network is 192.168.2.0/23
The IP of bond0 and bond1 should be in differente networks? Can i give, for
example,
Hello,
I’ve manually prepared my glusterFS volumes by the glusterCLi, one for the
Engine, and the other for Data. Both are detected by the engine as “GlusterFS”,
however, there’s no “Bricks” tab in both and I cannot see the bricks status
from the engine. Is there a required setting or parameter
Hi all,
I'm running a glusterFS setup v 8.6 with two node and one arbiter. Both nodes
and arbiter are CentOS 8 Stream with oVirt 4.4. Under gluster I have a LVM thin
partition.
VMs running in this cluster have really poor write performance, when a test
directly performend on the disk score
Hi All,
Does anyone have recommendations for GlusterFS monitoring/alerting software and
or plugins.
Kind regards
Simon...
___
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Privacy Statement:
I have an ovirt 4.3 on 3 Centos 7 with Gluster 9. Another Centos 7 server is
the Ovirt node, but only for management and file sharing.
Everything was fine until a power outage. Now node2 glusterfs will not spawn
the listening port for the brick..
All nodes are connected, but just no brick port
Hello,
I have 3 node HCI cluster with oVirt 4.4.6 and CentOS8.
For time to time (I belive) random brick on random host goes down
because health-check. It looks like
[root@ovirt-hci02 ~]# grep "posix_health_check" /var/log/glusterfs/bricks/*
I have researched and applied several tweaks to Gluster to improve performance
but on the vm side, depending on distribution, you can "tweak" the vm for
better performance on Gluster as well;
yum install tuned.noarch tuned-utils-systemtap.noarch tuned-utils.noarch
tuned-gtk.noarch -y
(GTK is
Hello,
What is the compatibility gluster version to work with oVirt 4.4.1 ?
Thanks
--
Jose Ferradeira
http://www.logicworks.pt
___
Users mailing list -- users@ovirt.org
To unsubscribe send an email to users-le...@ovirt.org
Privacy Statement:
I currently have 3 nodes, one is the engine node and 2 Centos 7 hosts, and I
plan to add another Centos 7 KVM host once I get all the vm's migrated. I have
san storage plus the raid 5 internal disks. All OS are installed on mirrored
SAS raid 1. I want to use the raid 5 vd's as exports, ISO and
Hello
I have quite some trouble getting Gluster to work.
I have 4 nodes running CentOS and oVirt. These 4 nodes is split up in 2
clusters.
I do not run Gluster via oVirt, i run it stand alone to be able to use all 4
nodes into one gluster volume.
I can add all peers successfully, and i
Hello everyone,
I've installed oVirt on 8 nodes of a MacroServer (SuperMicro Microcloud): 7
Nodes with oVirt Node installed and 1 Node with Centos 7 and oVirt installed.
The last one works like hypervisor and node.
I would use all the storage of all nodes like a Gluster storage, so I've
Currently when LibgfApiSupported is enabled it looks like the startup command
for the VM has the Gluster hostname always set to the same host. How does that
work if that host is down? In my case GlusterFS has 3x replication and
distribution enabled but if the first host is down the VMs don't
Hi Guys,
I would like to use GlusterFS distributed-replicated with arbiter volume on
4 nodes for oVirt.
Can you tell me what tuning parameters should I set for such volume for
best VM performance?
Does it make any sense to upgrade from Glusterfs 3.12 to 4.1 or even 5.0?
Thanks!
Jarek
All,
Now that GlusterFS 4.1 LTS has been released, and is the "default"
version of GlusterFS in CentOS (you get this from
"centos-release-gluster" now), what's the status with regards to oVirt?
How badly is oVirt 4.2.4 likely to break if one were to upgrade the
gluster* packages to 4.1?
Thanks,
It looks like we are experiencing a bug in the version of glusterfs
included with ovirt 4.2.3. It looks like glusterfs 3.12.x has an issue
where it consumes large amounts of ram which has caused our HV report
storage errors and pause VMs.
https://bugzilla.redhat.com/show_bug.cgi?id=1496379
Is
I have a 4 node setup (centos 7) with hosted engine on glusterfs (replica 3
arbiter1). Gluster fs is like this
ohost01 104G brick (real data)
ohost02 104g brick (real data)
ohost04 104g brick (arbiter)
ohost05 104g partition used as nfs-storage.
hosted engine is on gluster. I also have an
On Mon, Mar 19, 2018 at 5:57 PM, Jayme wrote:
> I'm spec'ing a new oVirt build using three Dell R720's w/ 256GB. I'm
> considering storage options. I don't have a requirement for high amounts
> of storage, I have a little over 1TB to store but want some overhead so I'm
>
I'm spec'ing a new oVirt build using three Dell R720's w/ 256GB. I'm
considering storage options. I don't have a requirement for high amounts
of storage, I have a little over 1TB to store but want some overhead so I'm
thinking 2TB of usable space would be sufficient.
I've been doing some
Gluster would be to overcomplicate this if you only want local storage
on both to be reachable over the network.
Simplest way is to setup an nf server on both nodes and create a
storage domain for each.
Gluster is a way to secure your data and replicate them over several
nodes. so that if one node
For it to work you need to have the bricks in replicate. Of brick on
each server.
If you only have two nodes. The quoum will be to low so it will set the
gluster to failsafe mode until the other brick comes online.
For it to work properly you need three nodes with one brick or two
nodes and a
Hello,
I'm very new to oVirt and glusterFS, so maybe I got something wrong...
I have the oVirt engine installed on a separate server and I have also two
physical nodes. On every node I configure glusterFS, the volume is in
distribution mode and have only one brick, from is one node. Both volumes
I am currently in the process of researching converting an existing SMB
infra to virtual. Ovirt/RHEV is a strong contender and checks off a lot
of boxes on our list. GlusterFS is appealing but I am finding it very
difficult to find any answers or stats/numbers regarding how well it can
perform
Hi,
Can you please check if you have vdsm-gluster package installed on the
system ?
Thanks
kasturi
On Wed, Aug 16, 2017 at 6:12 PM, Vadim wrote:
> Hi, All
>
> ovirt 4.1.4 fresh install
> Constantly seeing this message in the logs, how to fix this:
>
>
> VDSM kvm04 command
Can you check if you have vdsm-gluster rpm installed on the hosts?
On Wed, Aug 16, 2017 at 7:08 PM, Vadim wrote:
> In vdsm.log
>
> 2017-08-16 16:34:15,314+0300 ERROR (jsonrpc/5) [jsonrpc.JsonRpcServer]
> Internal server error (__init__:577)
> Traceback (most recent call last):
>
In vdsm.log
2017-08-16 16:34:15,314+0300 ERROR (jsonrpc/5) [jsonrpc.JsonRpcServer] Internal
server error (__init__:577)
Traceback (most recent call last):
File "/usr/lib/python2.7/site-packages/yajsonrpc/__init__.py", line 572, in
_handle_request
res = method(**params)
File
Hi, All
ovirt 4.1.4 fresh install
Constantly seeing this message in the logs, how to fix this:
VDSM kvm04 command GlusterTasksListVDS failed: 'AutoProxy[instance]' object has
no attribute 'glusterTasksList'
VDSM kvm04 command GlusterTasksListVDS failed: 'AutoProxy[instance]' object has
no
On 05/18/2017 10:35 AM, TranceWorldLogic . wrote:
Thanks,
Would you also explain about my 2nd question ?
let say hostB mounted glusterFS partition by using backup vol (e.g.
hostB) and after some time Host A come online, will GlusterFS client
(mount) automatically switch to Host A ?
mount
Thanks,
Would you also explain about my 2nd question ?
let say hostB mounted glusterFS partition by using backup vol (e.g. hostB)
and after some time Host A come online, will GlusterFS client (mount)
automatically switch to Host A ?
Thanks,
~Rohit
On Thu, May 18, 2017 at 9:43 AM, knarra
Hi,
backup-volfile-servers is mainly used to avoid SPOF. For example
take a scenario where you have Host A and Host B and when you try to
mount a glusterfs volume using Host A with backup-volfile-servers
specified, if Host A is not accessible, mount will happen with Host B
which is
Hi,
Before trying out, I want to understand how glusterfs will react for below
scenario.
Please help me.
Let consider I have two host hostA and hostB
I have setup replica volume on hostA and hostB. (consider as storage domain
for DATA in ovirt).
I have configure data domain mount command with
I figured it out. I forgot that these gluster volumes as recommended by the
Ovirt Glusterized setup were created as Replica 3 Arbiter 1 volumes, so now I
understand what that truly means, One brick only contains the directory and
meta data and so will always be smaller actual disk use.
This is a self hosted Glusterized setup, with 3 hosts. I have had some
glusterfs data storage domains have some disk issues where healing was
required. The self heal seemed to startup and the Ovirt Management portal
showed healing taking place in the Volumes/Brick tab. Later it showed
ovirt-release36 RPMs have been updated with the new glusterfs key url.
Thanks,
On Tue, Mar 22, 2016 at 5:47 PM, Fabrice Bacchella <
fabrice.bacche...@orange.fr> wrote:
> The command
> rpm --import
> https://download.gluster.org/pub/gluster/glusterfs/LATEST/rsa.pub
> worked too.
> >
>
> > Le 22
The command
rpm --import https://download.gluster.org/pub/gluster/glusterfs/LATEST/rsa.pub
worked too.
>
> Le 22 mars 2016 à 17:46, Robert Story a écrit :
>
> On Tue, 22 Mar 2016 17:28:20 +0100 Fabrice wrote:
> FB> I tried to add a new host on a RHEL7, but it fails.
> FB>
On Tue, 22 Mar 2016 17:28:20 +0100 Fabrice wrote:
FB> I tried to add a new host on a RHEL7, but it fails.
FB>
FB> In the ovirt-host-deploy-20160322171347-XXX-6ba9d4a3.log file, I found:
FB>
FB> warning:
Hello Fabrice,
i saw the same for a fresh installation of centos 7 (1511) and actuall
ovirt version. I wrote a solution here:
http://taste-of-it.de/ovirt-centos-installation-glusterfs-gpg-key-not-found/
I think its a bug.
Am 2016-03-22 17:28, schrieb Fabrice Bacchella:
I tried to add a new
I tried to add a new host on a RHEL7, but it fails.
In the ovirt-host-deploy-20160322171347-XXX-6ba9d4a3.log file, I found:
warning:
/var/cache/yum/x86_64/7/ovirt-3.6-glusterfs-epel/packages/glusterfs-libs-3.7.9-1.el7.x86_64.rpm:
Header V4 RSA/SHA256 Signature, key ID d5dc52dc: NOKEY
Il 09/07/2015 18:21, Stefano Stagnaro ha scritto:
The installation ended up correctly with ovirt-release35-005-1.noarch.rpm you
provided.
Thanks for the feedback, releasing it.
Thanks.
--
Sandro Bonazzola
Better technology. Faster innovation. Powered by community collaboration.
See
Il 09/07/2015 11:48, Stefano Stagnaro ha scritto:
Hi,
adding epel-6 gives another error:
Error: Package: vdsm-gluster-4.16.20-0.el6.noarch (@ovirt-3.5)
Requires: vdsm = 4.16.20-0.el6
Removing: vdsm-4.16.20-0.el6.x86_64 (@ovirt-3.5)
vdsm =
Il 09/07/2015 11:48, Stefano Stagnaro ha scritto:
Hi,
adding epel-6 gives another error:
Error: Package: vdsm-gluster-4.16.20-0.el6.noarch (@ovirt-3.5)
Requires: vdsm = 4.16.20-0.el6
Removing: vdsm-4.16.20-0.el6.x86_64 (@ovirt-3.5)
vdsm =
Il 09/07/2015 11:48, Stefano Stagnaro ha scritto:
Hi,
adding epel-6 gives another error:
Error: Package: vdsm-gluster-4.16.20-0.el6.noarch (@ovirt-3.5)
Requires: vdsm = 4.16.20-0.el6
Removing: vdsm-4.16.20-0.el6.x86_64 (@ovirt-3.5)
vdsm =
Il 09/07/2015 11:48, Stefano Stagnaro ha scritto:
Hi,
adding epel-6 gives another error:
Error: Package: vdsm-gluster-4.16.20-0.el6.noarch (@ovirt-3.5)
Requires: vdsm = 4.16.20-0.el6
Removing: vdsm-4.16.20-0.el6.x86_64 (@ovirt-3.5)
vdsm =
The installation ended up correctly with ovirt-release35-005-1.noarch.rpm you
provided.
Thanks.
--
Stefano Stagnaro
Prisma Telecom Testing S.r.l.
Via Petrocchi, 4
20127 Milano – Italy
Tel. 02 26113507 int 339
e-mail: stefa...@prismatelecomtesting.com
skype: stefano.stagnaro
On gio,
Hi,
Can you please try enabling epel 6 repo. It should have the needed
dependencies.
-Regards
Darshan N
- Original Message -
From: Stefano Stagnaro stefa...@prismatelecomtesting.com
To: users@ovirt.org
Sent: Wednesday, July 8, 2015 4:09:42 PM
Subject: [ovirt-users] GlusterFS host
: Wednesday, July 8, 2015 4:09:42 PM
Subject: [ovirt-users] GlusterFS host installation failed
Hi,
host installation in a glusterfs cluster is failing due to dependecies
errors:
Error: Package: glusterfs-server-3.7.2-3.el6.x86_64
(ovirt-3.5-glusterfs-epel)
Requires
The libs are available for epel6 as well I remember.
Worth giving a try.
Regards,
Shubhendu
On 07/09/2015 03:50 PM, Shubhendu Tripathi wrote:
I installed librcu using the below command -
yum install
ftp://ftp.muug.mb.ca/mirror/fedora/epel/7/x86_64/u/userspace-rcu-0.7.9-1.el7.x86_64.rpm
I installed librcu using the below command -
yum install
ftp://ftp.muug.mb.ca/mirror/fedora/epel/7/x86_64/u/userspace-rcu-0.7.9-1.el7.x86_64.rpm
Regards,
Shubhendu
On 07/08/2015 04:09 PM, Stefano Stagnaro wrote:
Hi,
host installation in a glusterfs cluster is failing due to dependecies
Hi,
host installation in a glusterfs cluster is failing due to dependecies errors:
Error: Package: glusterfs-server-3.7.2-3.el6.x86_64 (ovirt-3.5-glusterfs-epel)
Requires: pyxattr
Error: Package: glusterfs-server-3.7.2-3.el6.x86_64 (ovirt-3.5-glusterfs-epel)
Requires:
Hello,
I'm in the planning stage of setting up a new oVirt cluster, where I would
prefer to use the local disks of the hypervisors for a GlusterFS storage
domain. What is the current recommendation (for version 3.5.x)?
I found this presentation which seems to suggest that it's possbile with
some
Please note I will -not- be using Hosted Engine.
On 6 July 2015 at 13:54, Tiemen Ruiten t.rui...@rdmedia.com wrote:
Hello,
I'm in the planning stage of setting up a new oVirt cluster, where I would
prefer to use the local disks of the hypervisors for a GlusterFS storage
domain. What is the
On 06/07/15 16:01, Tiemen Ruiten wrote:
Also, while I can imagine why fencing might be a problem, what would
be the issue with HA?
/users
Hi,
Fencing is required for HA. If a box hosting HA vms seem to have gone
away, it *has* to be guaranteed those VMs are not running before they
are
Hey,
As for libgfapi, there are several uses for it in oVirt, not all fully
implemented at his point. However, you need to remember that this is an
optimization so whenever it's ready it will be release (as a part of the
relevant version) but not having it is still not lacking any functionality.
Also, while I can imagine why fencing might be a problem, what would be the
issue with HA?
On 6 July 2015 at 16:52, Tiemen Ruiten t.rui...@rdmedia.com wrote:
Thanks Doron,
I would initially start with a 3 host cluster, possibly adding more hosts
later on. Is this enough to ensure integrity
On 06/07/15 15:03, Tiemen Ruiten wrote:
Please note I will -not- be using Hosted Engine.
On 6 July 2015 at 13:54, Tiemen Ruiten t.rui...@rdmedia.com
mailto:t.rui...@rdmedia.com wrote:
Hello,
I'm in the planning stage of setting up a new oVirt cluster, where I
would prefer to
Thanks Doron,
I would initially start with a 3 host cluster, possibly adding more hosts
later on. Is this enough to ensure integrity of the Gluster storage domain,
eg. in case of host failure?
What are recommendations (if they exist) for the type of Gluster volume for
a 3-5 host cluster
Hi.
I am testing oVirt 3.5.2 with 3 hosts (Dell R210). Storage type is
GlusterFS (replicate 3): each host has a single 3TB HDD. When I put one
host into maintence mode, then reboot it and after system has been started,
the glusterfsd proccess takes a long time (more then hours with gigabyte
@ovirt.org
Subject: [ovirt-users] glusterfs takes a long time to syncing after host has
been rebooted
Hi.
I am testing oVirt 3.5.2 with 3 hosts (Dell R210). Storage type is GlusterFS
(replicate 3): each host has a single 3TB HDD. When I put one host into
maintence mode, then reboot it and after
Hi,
i have the same setup and problem. Nothing really happens on my SAN
Network interface. I can only see with iotop a read rate of about
50MB/sec on every node.
So i wonder if it tries to heal/verify checksums of files. Maybe it does
that so slow to prevent over stressing the I/O of the
On 23/04/15 00:47, Will Dennis wrote:
Hi all,
Can someone tell me if it’s possible or not to utilize GlusterFS mounted
as native (i.e. FUSE) for a storage domain with oVirt 3.5.x? I have two
nodes (with a third I’m thinking of using as well) that are running
Gluster, and I’ve
Hi all,
Can someone tell me if it's possible or not to utilize GlusterFS mounted as
native (i.e. FUSE) for a storage domain with oVirt 3.5.x? I have two nodes
(with a third I'm thinking of using as well) that are running Gluster, and I've
created the two volumes needed for hosted engine setup
On 24/03/15 02:43, Punit Dambiwal wrote:
I have 4 servers.
afaik this is a real problem regarding
split brains situation, like in every cluster
you should avoid even numbers of servers in
a cluster, so you have always a quorum.
use 3 or 5 servers, not 4.
HTH
--
Mit freundlichen Grüßen /
Hi,
I want to use Glusterfs with Ovirt 3.5...please help me to make the
architecture stable for the production use :-
I have 4 servers...every server can host 24 SSD disk(As bricks)..i want to
deploy distributed replicated storage with replica =2i don't want to
use the Hardware RAID...as i
: Kanagaraj kmayi...@redhat.com
Para: Jason Brooks jbro...@redhat.com, supo...@logicworks.pt
Cc: Users@ovirt.org
Enviadas: Terça-feira, 3 De Março de 2015 4:43:50
Assunto: Re: [ovirt-users] Glusterfs storage
If you are managing the gluster volume through ovirt, you could just
select the volume
-
From: supo...@logicworks.pt
To: Aharon Canan aca...@redhat.com
Cc: Users@ovirt.org
Sent: Monday, March 2, 2015 8:25:13 AM
Subject: Re: [ovirt-users] Glusterfs storage
Thanks Aharon,
After a couple of hours, the chown 36:36 did the trick, now I have the domain
up.
This is a good way to set those
Canan
int phone - 8272036
ext phone - +97297692036
email - aca...@redhat.com
- Original Message -
From: supo...@logicworks.pt
To: Users@ovirt.org
Sent: Monday, March 2, 2015 5:55:33 PM
Subject: [ovirt-users] Glusterfs storage
Hi,
I have setup up 2 hosts, host1 with hosted
Hi,
I have setup up 2 hosts, host1 with hosted engine, and on host 2, since I have
a spare disk, I want to setup a glusterfs domain storage.
I'm using Centos7 and ovirt 3.5.1.
The 2 hosts and hosted engine are up and running.
How can I configure the glusterfs storage?
I installed glusterfs
phone - +97297692036
email - aca...@redhat.com
- Original Message -
From: Aharon Canan aca...@redhat.com
To: supo...@logicworks.pt
Cc: Users@ovirt.org
Sent: Monday, March 2, 2015 6:00:40 PM
Subject: Re: [ovirt-users] Glusterfs storage
Hi
First, You need to create gluster volume
Assunto: Re: [ovirt-users] Glusterfs storage
Hi
First, You need to create gluster volume. Do not forget to start the volume.
then the chown 36:36 volume directory name
now you need to create new glusterfs domain, and to point to the gluster
server name:/volume name
Regards
- Original Message -
From: supo...@logicworks.pt
To: Aharon Canan aca...@redhat.com
Cc: Users@ovirt.org
Sent: Monday, March 2, 2015 8:25:13 AM
Subject: Re: [ovirt-users] Glusterfs storage
Thanks Aharon,
After a couple of hours, the chown 36:36 did the trick, now I have
Subject: Re: [ovirt-users] GlusterFS Centos 7 unable to mount NFS on gluster
members
On Mon, 2015-01-12 at 20:03 -0700, Donny Davis wrote:
Here is a quick rundown of the system, and the problem.
All hosts on centOS 7 fully up to date
GlusterFS is running on 6 servers, 3x2 distribute
Here is a quick rundown of the system, and the problem.
All hosts on centOS 7 fully up to date
GlusterFS is running on 6 servers, 3x2 distribute/replicate.
CTDB is running on all hosts
I am unable to mount via nfs the exported volume on any of the gluster
server members.
I am able to
On Mon, 2015-01-12 at 20:03 -0700, Donny Davis wrote:
Here is a quick rundown of the system, and the problem.
All hosts on centOS 7 fully up to date
GlusterFS is running on 6 servers, 3x2 distribute/replicate.
CTDB is running on all hosts
I am unable to mount via nfs the
Hi Humble,
Seems this option 'backup-vol-file-servers' work in the beginning of
the setupis this option can automatically try to mount another server
if first one fail such as three months later after setup ??
Is glusterfs w/ libgfapi working for anyone?
Is this still a feature of oVirt?
Thanks, Jason
___
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
On 10/01/2014 06:23 PM, Jason Brooks wrote:
Is glusterfs w/ libgfapi working for anyone?
Is this still a feature of oVirt?
Thanks, Jason
___
Users mailing list
Users@ovirt.org
http://lists.ovirt.org/mailman/listinfo/users
it was disabled due to
The 'referred' mount point is the 'gluster server IP' and the VM behaviour
depends on the Gluster Volume availability as discussed before.
Reg#localhost instead of server IP, I havent tried this, but logically it
should work. You may test it. Also there is an option called
Hi,
but i want the way from the ovirt portal...if possible ??
Yes, its possible.
Also in my case if the mount point HV node goes down...all the VM's will
pause...and once the node come up..i need to manually poweroff the VM's and
manually start again...
I failed to interpret 'mount
Hi Humble,
Thanks for the update...the mount point is the ip address to mount the
gluster volume,so if this server goes down...all the VM's will pause :-
[image: Inline image 1]
Some one from community suggest me to use the localhost instead of the ip
address for HAbut i have doubt if i use
Hi Punit,
If you are using gluster volume for virt store, it is always recommend to
enable /considering virt store use case mentioned here :
http://gluster.org/documentation/use_cases/Virt-store-usecase/
Regarding how to add bricks to the volume , you can refer #
Hi Humble,
Thanks for the updatesbut i want the way from the ovirt portal...if
possible ??
Also in my case if the mount point HV node goes down...all the VM's will
pause...and once the node come up..i need to manually poweroff the VM's and
manually start again...
Someone from community
Hi,
I have 4 node GlusterFS Distributed Replicate volume...the same 4 host node
i am using for compute purposenow i want to make it HAso if any
host goes down .VM will not pause and it will migrate to another
available node...
1. Can any one have any document or reference to do this
I was never able to achieve a stable system that could survive the loss of a
single node with glusterfs. I attempted to use replica 2 across 3 nodes (which
required 2 bricks per node as the number of bricks must be a multiple of the
replica, and you have to order them so the brick pairs span
Hi,
I have some HA related concern about glusterfs with Ovirt...let say i have
4 storage node with gluster bricks as below :-
1. 10.10.10.1 to 10.10.10.4 with 2 bricks each and i have distributed
replicated architecture...
2. Now attached this gluster storge to ovrit-engine with the following
You need to setup a virtual IP to use as the mount point, most people use
keepalived to provide a virtual ip via vrrp for this. Setup something like
10.10.10.10 and use that for your mounts.
Right now, if 10.10.10.2 goes away, all your gluster mounts go away and your
VMs get paused because the
Hi,
Thanks...can you suggest me any good how to/article for the glusterfs with
ovirt...
One strange thing is if i will try both (compute storage) on the same
node...the below quote not happen
-
Right now, if 10.10.10.2 goes away, all your gluster mounts go away and
your
Don't forget to take into consideration quroum, that's something
people often forget
The reason you're having the current happen, is gluster only uses the
initial IP address to get the volume details. After that it'll connect
directly to ONE of the servers, so with your 2 storage server case,
50%
Hi Andrew,
Thanks for the updatethat means HA can not work without VIP in the
gluster,so better to use the glusterfs with the VIP to take over the
ip...in case of any storage node failure...
On Fri, Jul 4, 2014 at 12:35 PM, Andrew Lau and...@andrewklau.com wrote:
Don't forget to take into
Or just localhost as your computer and storage are on the same box.
On Fri, Jul 4, 2014 at 2:48 PM, Punit Dambiwal hypu...@gmail.com wrote:
Hi Andrew,
Thanks for the updatethat means HA can not work without VIP in the
gluster,so better to use the glusterfs with the VIP to take over the
Hi Andrew,
Yes..both on the same node...but i have 4 nodes of this type in the same
clusterSo it should work or not ??
1. 4 physical nodes with 12 bricks each(distributed replicated)...
2. The same all 4 nodes use for the compute purpose also...
Do i still require the VIP...or not ??
Hi Itamar,
i assume this is around gluster deployment/split-brains/etc., since we try
to resume and fail
We are progressing on bz.
Looks like quorum configuration playing a role here. I will follow up on
the same bug report.
--Humble
On Mon, Jun 16, 2014 at 7:10 PM, Itamar Heim
Hi,
that has been fixed since 3.3 with auto-resume paused vm's after EIO
Thanks Itamar .
I had a BZ open about this with some traction, but i forgot to keep up
with the requests and it's fallen behind
https://bugzilla.redhat.com/show_bug.cgi?id=1058300
Even manually, they won't resume.
On 06/16/2014 04:20 PM, Humble Devassy Chirammal wrote:
Hi,
that has been fixed since 3.3 with auto-resume paused vm's after EIO
Thanks Itamar .
I had a BZ open about this with some traction, but i forgot to keep up
with the requests and it's fallen behind
On 06/02/2014 01:10 PM, Humble Devassy Chirammal wrote:
Hi Andrew,
Afaict, there should be manual intervention to resume a 'paused vm' in
any storage domain even if VM is marked as HA..
that has been fixed since 3.3 with auto-resume paused vm's after EIO
Also, I failed to understand the
Hi Andrew,
Afaict, there should be manual intervention to resume a 'paused vm' in any
storage domain even if VM is marked as HA..
Also, I failed to understand the setup you have, that said, you mentioned:
resuming a VM from a paused state on top
of NFS share? Even when the VMs are marked as
Hi Humble,
On Mon, Jun 2, 2014 at 8:10 PM, Humble Devassy Chirammal
humble.deva...@gmail.com wrote:
Hi Andrew,
Afaict, there should be manual intervention to resume a 'paused vm' in any
storage domain even if VM is marked as HA..
I had a BZ open about this with some traction, but i forgot to
Hi,
Has anyone had any luck with resuming a VM from a paused state on top
of NFS share? Even when the VMs are marked as HA, if the gluster
storage goes down for a few seconds the VMs go to a paused state and
can never be resumed. They require a hard reset.
I recall when using NFS to not have
Hi,
did you miss the email's body :-) ?
Thanks,
Gilad.
- Original Message -
From: Gabi C gab...@gmail.com
To: users@ovirt.org
Sent: Wednesday, May 21, 2014 11:28:26 AM
Subject: [ovirt-users] glusterfs quetions/tips
___
Users
ignore :-) saw the later thread...
Thanks,
Gilad.
- Original Message -
From: Gilad Chaplik gchap...@redhat.com
To: Gabi C gab...@gmail.com
Cc: users@ovirt.org
Sent: Saturday, May 24, 2014 11:32:14 AM
Subject: Re: [ovirt-users] glusterfs quetions/tips
Hi,
did you miss
1 - 100 of 111 matches
Mail list logo