CS>Difference between ionic silver and Ag4O4 "SilverSol"

Thu, 09 Apr 2020 16:51:46 -0700


Hello Group,

      I make my own ionic silver at 10ppm using a wonderful Silver Puppy machine.  It's pretty much a set it and forget it device.  Every batch comes out the same with a crystal clear look.  Takes about 8 - 9 hours to make a quart.  My question is this; is there any difference between the solution I'm making  and the much advertised Silver Sol Ag4O4 made by American Biotech Labs?  I get great results using my home made silver but am curious to know if there are any differences physically or therapeutically between the two.  Thanks so  much for a wonderful group.  Just FYI... I take 2 TB daily, 1 in the AM and 1 in the PM, keeping it in my mouth for a few minutes before swallowing to get the ions absorbed before hitting the stomach.  I also nebulize with it for a minute or two a couple of times a day.  Doing that got rid of a terrible bronchitis I had for 7 weeks.  It was gone in less than one!

      Bob
-----Original Message-----
From: Douglas Haack
Sent: Apr 9, 2020 4:05 PM
To: Silverlist Post
Subject: CS>My unique CS maker....with a SIMPLE STIRRING mechanism.

The IMPORTANCE of monitoring the increasing MilliAmps in your Brew cycle....

Years ago "Ole Bob" Berger RIP, designed a CS maker unit of -- 6 x A's and 6 x C's -- in a circular pattern of 4 inch diameter... centre -- have a 1.5 volt motor centered, the protruding axel has a stiff wire (non metal) covering (in my case the hollow covering slips onto the axel and a tiny ring of copper wire is carefully secured/twisted with pliers, thus the copper is stretched to hold the "Stirrer", permanently in place on the axel and it works!!).

I use 34 volts power supply DC (the amps are almost at zero) for my 12 sliver thin rods. The 1.5 volt motor is 15 years old now and I use up to 10/12 volts to spin at fast stirring rate to agitate 6 litres...the motor takes this higher voltage...I use a separate  Wall-Wort dial-able voltage unit...with an attached digital read-put...or U can use D-Cell 1,5 volt battery, I've tried that and works well...


Have a multi-meter (Bob's instructions) in the power circuit, to monitor the Milliamps in real-time (can be switched on and off), this indicates what's happening in the CS brew/distilled water etc -- I dope the 6 litres 2ppm d-water with 200ml of CS used/saved for this purpose to "START" the electrolysis process quickly -- 20 years ago people were using salt as a starter!!! This a dire No-No!!! today we are smarter...

Monitoring the Milliamps as they increase in the brew cycle, allows U to stop the process B4 U "over-cook" (this is trial and error and U will over-cook!! Until U  have "graphed/carefully observed" your voltage and time and find the "ideal brew time" in relation to TIME/Voltage/PPM with your TDS meter) and if the brew turns darker (after a few days), not good and I don't sue it... a nice light white Wine color is OK -- CLEAR is best I find, just my preference...!!!

Bob wrote a small book (he was an Electro Engineer), on his passing I tried to buy the edition from the family -- ahd some great information. simple but technical --- I offered $2K (15 years ago), they refused and the book has disappeared... I have a copy somewhere...It would have kept his name alive...

My contribution after 20 plus years...

In SILvation...Douglas H -- Australia
-- The Silver List is a moderated forum for discussing Colloidal Silver. Rules and Instructions: http://www.silverlist.org Unsubscribe: Archives: http://www.mail-archive.com/[email protected]/maillist.html Off-Topic discussions: List Owner: Mike Devour