On Tue, 21 Nov 2000, russ e rosser wrote:

> Very enlightening, but would any of this apply to 'wall warts', which
> never have a 3rd prong?  --Russ

The GFI's don't measure the current in the ground lead, but react
to the difference in current between the hot and neutral side of the
power line. There should never be a difference between the two - if
there is, it might be flowing through the ground lead, but it might
also be flowing through a human body to the cold water pipe. In either
case, the GFI will trip removing power.

John

> 
> On Tue, 21 Nov 2000 17:40:55 -0500 Marshall Dudley <[email protected]>
> writes:
> > russ e rosser wrote:
> > 
> > > Doesn't a GFI just have an internal breaker that's set at a usable 
> > amp
> > > rating for appliances?
> > 
> > No, a GFI breaker is a "ground fault interrupter."  It senses if 
> > current is
> > going to ground instead of back the other wire, and breaks th 
> > circuit
> > immediately if so.  I am not sure where they normally break, I 
> > thought it was
> > about 5 mA, but this site claims they cut out at 2 mA.
> > http://www.suttondesigns.com/glossary/gfci.shtml
> > 
> > > If so, it would be triggered by the buildup of
> > > *heat* which requires precious milliseconds, if not seconds.
> > 
> > These devices are not sensitive to heat and do not use heat like a 
> > normal
> > breaker.  They work in about 1/50 second although
> > http://www.misterfixit.com/gfi.htm claims they operate in about 10 
> > msec.
> > 
> > > If the
> > > wands were in series with the short, I'm afraid *the body* might 
> > supply
> > > enough resistance (up to 1 Meg ohm, initially) to delay the 
> > breaker
> > > response.
> > 
> > 120 VAC and 1 megohm gives .12 mA.  That is not enough current to 
> > make it cut
> > out, a fuse blow, or to even feel.
> > 
> > > The bottom line, of course, is to stop current flow >5mA
> > > through the wands.
> > 
> > 2 mA is less than 5 mA, if that is a correct figure.
> > 
> > >  Amid any uncertainty as to freak circuits that might
> > > *possibly* arise, a fuse in-line with a wand would *definitely* 
> > eliminate
> > > ANY conceivable shock above its rating.  Cheap, too, BTW.
> > 
> > I disagree.  How fast is the fuse, usually they can take seconds to 
> > melt when
> > near their rating.  Also they don't even approach their rating until 
> > you are
> > far above the 5 mA you indicate you want to guard against.
> > 
> > Marshall
> > 
> > see http://www.addisselectric.com/gfcipage.htm also.
> > 
> > 
> > --
> > The silver-list is a moderated forum for discussion of colloidal 
> > silver.
> > 
> > To join or quit silver-list or silver-digest send an e-mail message 
> > to: 
> > [email protected]  -or-  
> > [email protected]
> > with the word subscribe or unsubscribe in the SUBJECT line.
> > 
> > To post, address your message to: [email protected]
> > Silver-list archive: 
> > http://escribe.com/health/thesilverlist/index.html
> > List maintainer: Mike Devour <[email protected]>
> > 
> 
>