I have a question - why do many of you use PET plastic bottles instead of glass to keep the CS in? Thanks, Sally
Dave and Gwlynda Irek <[email protected]> wrote: @font-face { font-family: Tahoma;}...@font-face { font-family: Comic Sans MS;}...@page Section1 {size: 8.5in 11.0in; margin: 1.0in 1.25in 1.0in 1.25in; }P.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}LI.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}DIV.MsoNormal { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt; FONT-FAMILY: "Times New Roman"}A:link { COLOR: blue; TEXT-DECORATION: underline}SPAN.MsoHyperlink { COLOR: blue; TEXT-DECORATION: underline}A:visited { COLOR: purple; TEXT-DECORATION: underline}SPAN.MsoHyperlinkFollowed { COLOR: purple; TEXT-DECORATION: underline}P.ArielOutline1 { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt 0.25in; TEXT-INDENT: -0.25in; FONT-FAMILY: Arial}LI.ArielOutline1 { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt 0.25in; TEXT-INDENT: -0.25in; FONT-FAMILY: Arial}DIV.ArielOutline1 { FONT-SIZE: 12pt; MARGIN: 0in 0in 0pt 0.25in; TEXT-INDENT: -0.25in; FONT-FAMILY: Arial}SPAN.EmailStyle18 { COLOR: navy; FONT-FAMILY: Arial}DIV.Section1 { page: Section1}OL { MARGIN-BOTTOM: 0in}UL { MARGIN-BOTTOM: 0in}Thanks Bo for the reply. Your right I'm trying to make 20 PPM - on the highest setting. I check every gallon of distilled water with my meter before I put it in the SilverGen and the average is 0.2 so I'm pretty sure my water is ok. I brought new PET plastic water jugs for the CS which I have used since day one of making CS. I don't rinse them out between filling them with the next batch of CS - so they should not have any ozonation or minerals from tap water. I will try the next batch on the 12 o'clock setting and see what happens. Thanks so much for your help Gwlynda --------------------------------- From: bbanever [mailto:[email protected]] Sent: Wednesday, October 27, 2004 12:37 AM To: [email protected] Subject: CS> Gwlynda - There are two potential reasons for your yellow batches of CS. Firstly you are probably trying to make a batch in the 15 - 20ppm range. Try turning the dial down to 12 o'clock so you can make a 10ppm solution. This will always be clear. Secondly your water may be contaminated.... make sure the container is clean and the water is only pure distilled water with no ozonation or minerals added. Bob ----- Original Message ----- From: Dave and Gwlynda Irek To: [email protected] Sent: Tuesday, October 26, 2004 8:24 PM Subject: CS> I have been making CS with my SilverGen Pro 9 for about 2 months now. All my 5 gallon batches of CS has been clear until the last 2 - 5 gallons batches. The CS is yellow before I even get it out of the SilverGen. I turn the unit off as soon as it is finished and remove the silver and pump. Let the CS settle for a few minutes then pour it into a PET plastic water jug. Can someone tell me why my CS is turning yellow during and right after the unit turn off? Gwlynda --------------------------------- From: Jim Holmes [mailto:[email protected]] Sent: Tuesday, October 26, 2004 10:27 AM To: [email protected] Subject: RE: CS>question... Barrett is the quack. There is no citation in the medical literature of electro-colloidal silver, made with pure silver and pure water, causing Argyria. I have personally tried to have a dialog with that duck, and he is not willing to have one. Hulda Clark just successfully sued his ass. JOH -----Original Message----- From: sid aust [mailto:[email protected]] Sent: Monday, October 25, 2004 8:19 PM To: [email protected] Subject: CS>question... I am new to the forum and wondering what the side effects of taking CS. I just read one of Dr Barrett's article on how it will turn you grey and all kinds of bad stuff..and of course Dr Barrett is against everything good in alternative medicine..you can fine him on the quack forum... thanks Sid --------------------------------- Do you Yahoo!? Yahoo! Mail - You care about security. So do we.
