I would like to do that but I cannot create an account for the wiki. It seemsthe links are broken there...
http://sipx-wiki.calivia.com/index.php/Help:Contents When I click on "create an account" i get back to login screen... René 2009/7/9 M. Ranganathan <[email protected]> > On Thu, Jul 9, 2009 at 5:25 AM, Rene Pankratz<[email protected]> > wrote: > > I am using SipXecs 4.0.1. > > > > I already disabled all the settings in my X-Lite softphone as described > in > > the document. > > But it seemed the settings did not work until complete restart of X-Lite. > > Now everything works fine. > > > Please share your bluesip settings and any experiences. Please look at > the configuration table on the wiki and post the relevant settings. > > Thanks > > Ranga > > > > > > > 2009/7/9 Tony Graziano <[email protected]> > >> > >> What kind of phone are you using remotely? What kind of firewall? > >> A lot of consumer firewalls need to have the ALG (Application Layer > >> Gateway) for SIP turned off, though you may have to dig through the > advanced > >> settings to find it. If your remote phone is a softphone, you should > make > >> sure you have all the settings (local address/disable ice) configured as > >> described below.. > >> > >> What version of sipxecs do you have installed? > >> > >> >>> Rene Pankratz <[email protected]> 07/09/09 5:10 AM >>> > >> Thanks for your answer, i only set up the settings you described und > went > >> on > >> the steps. > >> There were only left the loopback and th local subnet the SipX and the > >> phones are in in the internet calling settings. > >> > >> But still there is the voice related problem. > >> When calling an internal phone the remote worker's phone is sent sdp > with > >> the internal address (behind NAT) of the called phone. So there is no > way > >> getting RTP into the office. > >> > >> René > >> > >> 2009/7/9 Tony Graziano <[email protected]> > >> > >> > I think you are misinterpreting the instructions. > >> > On that page you simply define your local routed subnets. > >> > Internet calling does not factor for remote worker setup except to > >> > define > >> > your internal subnets so that your system knows to accept those calls > >> > instead of rejecting them for lack of authentication via the proxy. > >> > Define > >> > your subnets (not the one your remote worker is on since it is not > >> > privately > >> > routed) and go to the next step. > >> > > >> > >>> Rene Pankratz <[email protected]> 07/09/09 4:11 AM >>> > >> > Hallo, > >> > after successfully configuring a SIP Trunk with bluesip I wanted to > add > >> > support for remote workers on my SipX-installation (4.0.1-015823). > >> > > >> > I wanted to configure remote workers as described here: > >> > > >> > > >> > > http://sipx-wiki.calivia.com/index.php/Configuring_remote_workers_cheatsheet > >> > > >> > But when I navigate to System->Internet Calling I cannot select the > SBC > >> > that > >> > is already configured for SIP Trunk. > >> > > >> > How can I select the existing or configure another internal SBC für > >> > handling > >> > remote workers? > >> > > >> > At this point remote clients can register, but RTP is handled > incorrect > >> > as > >> > the SDP part shows the internal IPs of the phones in SipX's internal > >> > network. > >> > > >> > Thanks in advance > >> > René > >> > </[email protected]> > >> > > >> </[email protected]></[email protected]> > > > > > > _______________________________________________ > > sipx-users mailing list [email protected] > > List Archive: http://list.sipfoundry.org/archive/sipx-users > > Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users > > sipXecs IP PBX -- http://www.sipfoundry.org/ > > > > > > -- > M. Ranganathan >
_______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users sipXecs IP PBX -- http://www.sipfoundry.org/
