BTW I'm only talking about FXO gateways. PRI doesn't give me this problem, only crappy FXO lines.
Josh Patten Assistant Network Administrator Brazos County IT Dept. (979) 361-4676 On 6/10/2010 6:16 PM, Josh Patten wrote: > I assume Patton do the voice detection then? > > Josh Patten > Assistant Network Administrator > Brazos County IT Dept. > (979) 361-4676 > > > On 6/10/2010 6:15 PM, Tony Graziano wrote: > >> I don't know of ANY sip device that will do that. There are "particular" >> things I have found gateways do not do. Send digits after connecting and say >> they are connected when they are not. >> ============================ >> Tony Graziano, Manager >> Telephone: 434.984.8430 >> Fax: 434.984.8431 >> >> Email: [email protected] >> >> LAN/Telephony/Security and Control Systems Helpdesk: >> Telephone: 434.984.8426 >> Fax: 434.984.8427 >> >> Helpdesk Contract Customers: >> http://www.myitdepartment.net/gethelp/ >> >> ----- Original Message ----- >> From: [email protected] >> <[email protected]> >> To: [email protected]<[email protected]> >> Sent: Thu Jun 10 19:00:01 2010 >> Subject: Re: [sipx-users] Audiocodes gateways disable voice detection >> >> I'm at my wits end. If I turn off all voice activity detection it simply >> leaves the call in early media (disconnecting it at 60 seconds) >> Is there any way to make the audiocodes show the call as "answered" >> immediately after dialing? >> >> Josh Patten >> Assistant Network Administrator >> Brazos County IT Dept. >> (979) 361-4676 >> >> >> On 6/10/2010 9:30 AM, Josh Patten wrote: >> >> >>> Due to the really crappy copper infrastructure in my area analog phone >>> lines have a lot of issues (mainly with echo and voice cutting out) with >>> audiocodes gateways which is remedied by tuning the incoming and >>> outgoing gain. If the voice gain is too high there is a lot of cutting >>> out and echo. The side effect of going to low on the gain (in or out) is >>> sometimes the "voice activity detector" doesn't ever realize there is >>> someone on the other side of the line, effectively leaving the call in >>> an early media state (the timer on the phone never starts, the call >>> isn't "officially" connected) which eventually disconnects. >>> >>> What I would like to do is disable voice activity detection altogether >>> and have the call connected immediately and the timer started when an >>> outbound call is made, no early media involved. I have tried playing >>> with all sorts of settings in the Audiocodes but nothing seems to make >>> this happen. Could anyone point me in the right direction? >>> _______________________________________________ >>> sipx-users mailing list [email protected] >>> List Archive: http://list.sipfoundry.org/archive/sipx-users >>> Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users >>> sipXecs IP PBX -- http://www.sipfoundry.org/ >>> >>> >>> >> _______________________________________________ >> sipx-users mailing list [email protected] >> List Archive: http://list.sipfoundry.org/archive/sipx-users >> Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users >> sipXecs IP PBX -- http://www.sipfoundry.org/ >> >> > _______________________________________________ > sipx-users mailing list [email protected] > List Archive: http://list.sipfoundry.org/archive/sipx-users > Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users > sipXecs IP PBX -- http://www.sipfoundry.org/ > _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users sipXecs IP PBX -- http://www.sipfoundry.org/
