I've never had to touch that setting. I think the timer starts when the telco switch connects (as in starts ringing).
It wasn't meant as a comparison. I just never have to fiddle with them once I set them up, so I really don't run into all this stuff. ============================ Tony Graziano, Manager Telephone: 434.984.8430 Fax: 434.984.8431 Email: [email protected] LAN/Telephony/Security and Control Systems Helpdesk: Telephone: 434.984.8426 Fax: 434.984.8427 Helpdesk Contract Customers: http://www.myitdepartment.net/gethelp/ ----- Original Message ----- From: Josh Patten <[email protected]> To: Tony Graziano <[email protected]> Cc: [email protected] <[email protected]> Sent: Thu Jun 10 19:30:31 2010 Subject: Re: [sipx-users] Audiocodes gateways disable voice detection Let's not turn this into a gateway manufacturer comparison Let me rephrase the question: What happens on you Polycom phone when you dial through your patton FXO gateway? Does the call timer immediately start when the phone starts ringing? Does the call timer start when someone answers the phone? If the former, then that is what I want but can't seem to get the audiocodes to do. If the latter, then the Patton is doing VAD to determine when early media should end. Josh Patten Assistant Network Administrator Brazos County IT Dept. (979) 361-4676 On 6/10/2010 6:27 PM, Tony Graziano wrote: > I haven't found anything they don't do that's reasonable. > > My issue with audiocodes is always tje reliabilituy factor. I like the > "ronco-ness, set it and forget it" aspect with Patton. > ============================ > Tony Graziano, Manager > Telephone: 434.984.8430 > Fax: 434.984.8431 > > Email: [email protected] > > LAN/Telephony/Security and Control Systems Helpdesk: > Telephone: 434.984.8426 > Fax: 434.984.8427 > > Helpdesk Contract Customers: > http://www.myitdepartment.net/gethelp/ > > ----- Original Message ----- > From: Josh Patten<[email protected]> > To: Tony Graziano<[email protected]> > Cc: [email protected]<[email protected]> > Sent: Thu Jun 10 19:16:28 2010 > Subject: Re: [sipx-users] Audiocodes gateways disable voice detection > > I assume Patton do the voice detection then? > > Josh Patten > Assistant Network Administrator > Brazos County IT Dept. > (979) 361-4676 > > > On 6/10/2010 6:15 PM, Tony Graziano wrote: > >> I don't know of ANY sip device that will do that. There are "particular" >> things I have found gateways do not do. Send digits after connecting and >> say >> they are connected when they are not. >> ============================ >> Tony Graziano, Manager >> Telephone: 434.984.8430 >> Fax: 434.984.8431 >> >> Email: [email protected] >> >> LAN/Telephony/Security and Control Systems Helpdesk: >> Telephone: 434.984.8426 >> Fax: 434.984.8427 >> >> Helpdesk Contract Customers: >> http://www.myitdepartment.net/gethelp/ >> >> ----- Original Message ----- >> From: [email protected] >> <[email protected]> >> To: [email protected]<[email protected]> >> Sent: Thu Jun 10 19:00:01 2010 >> Subject: Re: [sipx-users] Audiocodes gateways disable voice detection >> >> I'm at my wits end. If I turn off all voice activity detection it simply >> leaves the call in early media (disconnecting it at 60 seconds) >> Is there any way to make the audiocodes show the call as "answered" >> immediately after dialing? >> >> Josh Patten >> Assistant Network Administrator >> Brazos County IT Dept. >> (979) 361-4676 >> >> >> On 6/10/2010 9:30 AM, Josh Patten wrote: >> >> >>> Due to the really crappy copper infrastructure in my area analog phone >>> lines have a lot of issues (mainly with echo and voice cutting out) with >>> audiocodes gateways which is remedied by tuning the incoming and >>> outgoing gain. If the voice gain is too high there is a lot of cutting >>> out and echo. The side effect of going to low on the gain (in or out) is >>> sometimes the "voice activity detector" doesn't ever realize there is >>> someone on the other side of the line, effectively leaving the call in >>> an early media state (the timer on the phone never starts, the call >>> isn't "officially" connected) which eventually disconnects. >>> >>> What I would like to do is disable voice activity detection altogether >>> and have the call connected immediately and the timer started when an >>> outbound call is made, no early media involved. I have tried playing >>> with all sorts of settings in the Audiocodes but nothing seems to make >>> this happen. Could anyone point me in the right direction? >>> _______________________________________________ >>> sipx-users mailing list [email protected] >>> List Archive: http://list.sipfoundry.org/archive/sipx-users >>> Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users >>> sipXecs IP PBX -- http://www.sipfoundry.org/ >>> >>> >>> >> _______________________________________________ >> sipx-users mailing list [email protected] >> List Archive: http://list.sipfoundry.org/archive/sipx-users >> Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users >> sipXecs IP PBX -- http://www.sipfoundry.org/ >> >> _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users sipXecs IP PBX -- http://www.sipfoundry.org/
