Created http://track.sipfoundry.org/browse/XX-10340
Quite likely a release a blocker, but not my call. On Jul 30, 2012, at 14:05 , Kurt Albershardt wrote: > First time running setup script on a freshly built Centos 6 VM: > > > [root@sipx ~]# cat /etc/sysconfig/network > NETWORKING="yes" > GATEWAYDEV="venet0" > NETWORKING_IPV6="yes" > IPV6_DEFAULTDEV="venet0" > HOSTNAME="sipx.domain.com" > > [root@sipx ~]# sipxecs-setup > Network settings: > IP address : 192.168.X.26 > Would you like to configure your system's network settings? [ enter 'y' or > 'n' ] : n > Enter just the host name of this computer?. Example: myhost. [ press enter > for '"sipx' ] : > Enter just the domain name of your network? Example: mydomain.com [ press > enter for 'domain.com"' ] : > Is this the first server in your cluster? [ enter 'y' or 'n' ] : y > Configuring as the first server... > Tip: Use '"sipx.domain.com"' as your SIP domain if you are > setting up for the first time or if you know you are only going to setup one > server. This can make configuration easier. You can always change the value > later. > Enter SIP domain name [ press enter for 'domain.com"' ] : > Enter SIP realm [ press enter for 'domain.com"' ] : > Initial setup, this may take a few minutes... > Finishing system configuration, almost done... > done. > > > In a few more minutes you will be able to access the administration > interface from your web browser at the following URL: > > https://"sipx.domain.com"; > > > > > > > > On Jul 30, 2012, at 13:31 , Kurt Albershardt wrote: > >> Happened the first time I ran the script, FWIW. >> Install was updated 2-3x before I ran setup (due to dependency glitches) so >> it's not a good test case. >> I'll re-install on a clean VM and try again. >> >> >> >> >> On Jul 30, 2012, at 13:26 , Tony Graziano wrote: >> >>> i might venture a guess that re-running the script and taking the defaults >>> are doing this. if so, it would be incorrect and unwanted behavior. i think >>> in order to open a jira, it needs to be tried against a fresh install and >>> all patched up prior to running, then re-running the script. if it >>> continues to happen a jira would be in order. >>> >>> On Mon, Jul 30, 2012 at 3:11 PM, Kurt Albershardt <[email protected]> wrote: >>> Just tried a couple variants of that - first one left the host and domain >>> at default and then I manually typed everything else -- that produced the >>> same result at the end: >>> >>> https://"sipx.domain.com"; >>> >>> >>> Note spurious double quotes show in the proposed defaults: >>> >>> Enter just the host name of this computer?. Example: myhost. [ press enter >>> for '"sipx' ] : >>> Enter just the domain name of your network? Example: mydomain.com [ press >>> enter for 'domain.com"' ] : >>> >>> Re- running but manually entering those produced the expected: >>> >>> https://sipx.murray-hotel.com >>> >>> at the end. >>> >>> >>> >>> thanks~ >>> >>> >>> >>> >>> On Jul 30, 2012, at 13:01 , Tony Graziano wrote: >>> >>>> perhaps re-run the script and manually input the host and sipdomain >>>> (instead of hitting enter) to see if it removes the quotes. >>>> >>>> On Mon, Jul 30, 2012 at 2:59 PM, Kurt Albershardt <[email protected]> wrote: >>>> did not add quotes -- and the URL at the end still has them: >>>> >>>> >>>> [root@sipx ~]# sipxecs-setup --reset-all >>>> This will wipe all configuration data from this server. Are you sure? [ >>>> enter 'y' or 'n' ] : y >>>> Network settings: >>>> IP address : 192.168.X.26 >>>> Would you like to configure your system's network settings? [ enter 'y' >>>> or 'n' ] : n >>>> Enter just the host name of this computer?. Example: myhost. [ press enter >>>> for '"sipx' ] : >>>> Enter just the domain name of your network? Example: mydomain.com [ press >>>> enter for 'domain.com"' ] : >>>> Is this the first server in your cluster? [ enter 'y' or 'n' ] : y >>>> Configuring as the first server... >>>> Tip: Use '"sipx.domain.com"' as your SIP domain if you are >>>> setting up for the first time or if you know you are only going to setup >>>> one >>>> server. This can make configuration easier. You can always change the >>>> value >>>> later. >>>> Enter SIP domain name [ press enter for 'domain.com"' ] : sipx.domain.com >>>> Enter SIP realm [ press enter for 'sipx.domain.com' ] : >>>> Initial setup, this may take a few minutes... >>>> Finishing system configuration, almost done... >>>> done. >>>> >>>> >>>> In a few more minutes you will be able to access the administration >>>> interface from your web browser at the following URL: >>>> >>>> https://"sipx.domain.com"; >>>> >>>> >>>> >>>> On Jul 30, 2012, at 12:43 , Douglas Hubler wrote: >>>> >>>> > Somehow you might have double quotes around your host name. When >>>> > running sipxecs-setup, did you put double quotes around your host >>>> > name? > > _______________________________________________ > sipx-users mailing list > [email protected] > List Archive: http://list.sipfoundry.org/archive/sipx-users/
_______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users/
